havent seen any DFI boards yet. *EDIT* just posted right before me with the board i was looking at getting. Would like to see some AIR results from that board with 2x2gb ram.
Printable View
havent seen any DFI boards yet. *EDIT* just posted right before me with the board i was looking at getting. Would like to see some AIR results from that board with 2x2gb ram.
CPU stock with 1.20 Volts
http://img264.imageshack.us/img264/6...18vcorery7.png
nice honda whats the stock voltage? cause it looks like you are running pretty stable with a .15 undervolt. what was your difference in the temps?
Stock is 1.35.. here the the temps during that run
http://img111.imageshack.us/img111/5...h18cpu1ja9.png
what are your temps on stock clocks, stock voltage?
Just got my Phenom 940 in, stepping cacvc ac 0850bpdw. Have it hooked up to the Vapochill LS, gonna play around once I'm sure everything is good.
Everything I've done is with my vapo plugged in. Classes start Monday so I don't exactly have the room at the dorm to fidget around with setting up a vapochilled pc after working with some air cooling. Right now I need to go and find the new entries for the list, and can you guys please remember to at least post your steppings when you post everything? Its a pain to understand the results unless you include it because we're trying to see what steppings are best.
@ Sgt.McRuff - I need a screen of Prime95 or OCCT to put it in the stable list
@ iandh - I just need your stepping if you have it handy. Your stock voltage is actually low, its supposed to be 1.35v unless you just got a really good chip or something. I think you may need an upgraded bios before your troubles are over.
I think I :banana::banana::banana::banana:ed up my paste job and temps are killing me. This chip has more in it--it was prime stable until temps were above like 63C for half an hour. I tried 3.75GHz.
Anyway, I have a Prime95 stable result for you. I ran it overnight at a conservative set of settings to establish a baseline:
8h54m (user canceled)
3610MHz (225 x 16)
1.45V vCore
NB 2025MHz
Load temps were about 48C. You should really, really, really track load temps in your chart btw. If people with lower temps are doing the good results, that's really significant information.
load temps are nice but they can vary from cooler to cooler, from different ambients, etc.
http://www.abload.de/thumb/piicqrx.jpg
on my way xD
i have to set up xp32bit for ocing.. vista 64bit really is holding me back..
Oldguy932 I will post stepping when new hardware arrives...
Well, this doesn't make sense. I just insulated the socket with paste. Before the core temp would never move from 0C, but now its sitting at 2-3C. I'm thinking that the paste needs to set on top of the cpu, or I didn't get enough on the cpu itself. Socket temp according to speedfan is the same as it was. Maybe it needs to cure or something, I don't know, but I don't like it.
I'm also retrying 256x16 @ 1.575v right now. Core 2 gave me an error after 1:04 so I'm hoping that it was because I hadn't insulated.
@chew - The number was 154, so its not a cherry chip, but its also not like one of my 3xx ones that I have sitting around of other cpu's. Should be pretty good.
2hrs prime stable.. is that enough for the list?
http://www.abload.de/thumb/primev199.jpg
stepping is in my sig.
cpu is watercooled.
windows vista ultimate x64
unfortunately core 2 errored at 2hrs6mins. will try this with a little more vcore.
I think you might want to try with a little less vcore. Unless you got one that was like on the edge of the wafer, it should take 1.4v at most for that. Also, don't try for stability with anything above the 17.5x multi on that board, it just doesn't work yet.
Updating in the next few minutes.
Edit: Nevermind that, I forgot you were running x64.
iīve got no probs with the 18multi so far. too bad that my ram doesnīt do more than 1066mhz, so ocīing thru htt isnīt a good option, unless i let my ram run under 1000mhz.
either x64 is really tough, or my chip really is a dud that wants to be fed with high vīs ;)
Clearly I'm not grasping all these new K10 variables right. I thought I'd hit a limit if I put everything else down and upped the bus speed. I reached 300 with no issues. :(
http://halk.pwp.blueyonder.co.uk/300bus.gif
Impressive bus speed that's for sure. Tbh it's a lot like the base clock on i7 chips, it doesn't really do much to help peformance so most people keep it below 250.
Most of us are just doing straight multiplier overclocks since its unlocked
For the record Im having issues with multipliers as well except for me its anything above 16x, oddly enough it feels like the lower I put the multiplier the more stable the chip is for some odd reason...as 15x versus 16.5x seems stable with .5v less at the same speed which is weird.
That aside this chip refuses to go above 3.7 no matter what I throw at it, thankfully I'm content to just leave it there for now and play with the HTT clocks. I havent tried with 15x yet Im going to go do that now and see what happens.
EDIT: No go, sadly my ram isnt going to cooperate with this little experiment. Either I drop the multi of it down and then my board wont post 300+ or I go out of spec of my ram and it BSODs. :(
This K10 architecture is new to me and it's a long time since I overclocked anyway, so I'm stabbing in the dark. I'm trying to follow old methods, which is to turn all the knobs down and then turn one knob up to find the max. I do not think the 300 is realistic when I turn the other knobs back up though, not from the other clocks I've seen. But what do I know :)
anyone know a good bios for the K9A2 plat, im stuck with 10x NB multi on the 1.6 and i dont know of any flasher besides their Live update one, which only gives me the 1.6