add this stepping
Chip: Venice 3000+ LBBLE 0517APNW @ 2772MHz - 1.65V -> Water
Mobo: Dfi Lf nf4 ULTRA-D @SLI-D
Ram: Twinmos SP 2 x 512 2-2-2-6 @250MHz
Stable: 9 x 308 = 2.72 GHz
reaches: 9 x 315 = 2.83 GHz
Printable View
add this stepping
Chip: Venice 3000+ LBBLE 0517APNW @ 2772MHz - 1.65V -> Water
Mobo: Dfi Lf nf4 ULTRA-D @SLI-D
Ram: Twinmos SP 2 x 512 2-2-2-6 @250MHz
Stable: 9 x 308 = 2.72 GHz
reaches: 9 x 315 = 2.83 GHz
i think this chip got potential for more ocing. it's weird that i can run superpi 32M at 2850Mhz, but i can't play game or anything else. folding at 2850Mhz didn't last long either. i wonder if it's the memories that's holding me back. i just got these 2 sticks of dual channel ocz pc3200 rev. 2 plat. i'm using dfi bios 510-3fix. i have no idea what memory chips are on the sticks, so i can't use the proper bios. i'm assuming it's tccd chips. another thing is, i can run memtest at 280 and 285 with 1:1 mem timing, but windows doesn't like 1:1 timing and i have to use divider :(.
what cooling ?Quote:
Originally Posted by Dani
Here's a suicideshot with my venice.
IHS was removed because load temps were way to high (49-50° load, while 30-31° idle). Guess that the IHS didn't make good contact with the core.
Anyway, here's the screenie (just a 1M run, 32M would crash to the desktop after 2 minutes).
http://users.skynet.be/MetalHead/300...031superpi.png
http://users.skynet.be/MetalHead/300...validation.png
VapoQuote:
Originally Posted by TEDY
here is my new venice 0517dpmw :banana:
http://img129.imageshack.us/img129/7...dpmw2zk.th.jpg
anyone here running ocz pc3200 rev. 2 platinum dual channel 2x512MB on a dfi lanparty sli-dr and 3200 venice? i have this setup and my venice can oc pretty well. the problem i'm having is that the ocz mem can't run 270-290 htt with 1:1 sync with 1T timing. any ideas? if someone has a similar setup, please let me know. thanks in advance.
Had exactly the same problems dng29 with my 3200 0520 BPMW using bios 704-3, try disabling dynamic counter and tweak other ram settings
I ended up changing to 702-1 and much better now though I am sure you can fix the problem with ram tweaks but I have not got the perfect settings yet but sooooon :)
my 3200 venice is a week 19 with this code lbble 0519bpew. so far i can boot into winxp at 2900Mhz on an xp-120 on my dfi board. i can run superpi 1M fine, but that's about it. with 2850Mhz, i can pass 32M superpi and that's about it too. 2800Mhz is stable for gaming and folding and anything i throw at it. all these speeds were ran on a mem divider. i rather run 1:1 sync than async. I'd tried several bioses like 510-1fix, 510-2fix, 510-3fix, 704-3, and 510-3. none of these bioses will let me run 1:1 sync with htt at 270, 275, 280, 285 or 290 :(. i'll give 704-1 a try. i'm sure the chips on these sticks of ocz are tccd, but i'm tempted to take out the heatspreader and void the freaking warranty.
Have you ever seen a ybble 3000+/3200+ Venice?
i have not seen a ybble code, but i would like to see oc results. get cranking my good man :). have fun, good luck and hope it will oc like a rocket.
I just found one check out this post
http://www.xtremesystems.org/forums/...ighlight=ybble
Thx ;)Quote:
Originally Posted by njkid32
I have seen two ybble and they seem bad (max 2400 mhz), but that seems good.
Now I confront step...
can you give us a screenshot dng29 with you week 19 @ 2900 ?? with all the relevent settings like mine below, I have not tried 2900 yet but will soon, also I am running sync with the 702-1 :D
http://img215.imageshack.us/img215/5...0finish7ve.jpg
i'm at work right now, but i'll update you with my screenshots and settings. 2900Mhz is not 100% stable for me. 2850Mhz is somewhat stable since i can fold for hours. right now the pc is doing cpu burn-in and the room is freaking hot 28+ degree C :(.Quote:
Originally Posted by alpha0ne
Thanks m8
Heres a shot I thought I would never see, 2800 at last, with more to come
http://img68.echo.cx/img68/8416/pi3228000eu.jpg
sorry this took so long, but here's my suicide shot at 2900Mhz. it's not 100% stable, but i can use firefox and do light work in winxp :).
http://img289.imageshack.us/my.php?i...suicide7we.jpg
sorry the picture doesn't look great. my first time using imageshack :).
Good Luck men.Quote:
Originally Posted by dng29
I use OCZ rev2 v1:1 (TCC5) and work well for me.
http://img157.echo.cx/img157/8484/1079696qd.jpg
:toast:
Quote:
Originally Posted by LANero
wow that's an awesome 3000 venice you got there :). it beats my 3200 venice. i have 2 sticks of that ocz rev.2 ver 1.1 TCC5 too :). how the heck did you get it to run at 317htt? is this 1:1 sync ratio or divider? i see you're using bios 510-1. could you show me your bios settings for memories please. again you got a really nice chip :). my ocz rev 2 TCC5 will go any higher than 270htt with 1:1 ratio.
got my venice 3000+, was a week 17 BPEW, from chiefvalue. a low spinning fan on it. stock volts on CPU, 2.6Vimm, this is what i got:
ran prime for 7 hours, no screenie, i was too pissed on my keyboard for typing 2 letters instead of 1, rebooted the pc, hoping i won't have to find a store open on sunday, was wrong :(
- ram is TCCX, ramguy said.Code:Submitted by DyJohnnY
Submitted on Sat, 09 Jul 2005 22:04:45 +0200 with CPU-Z 1.29
CPU : AMD Athlon 64 3000+ (*1)
CPU PSN : AMD Athlon(tm) 64 Processor 3000+
CPU EXT : MMX (+) 3DNow! (+) SSE SSE2 SSE3 x86-64
CPU Cache : L1 : 64/64 KB - L2 : 512 KB
Core : Venice (0.09) / 0xFF0 / E3
Freq : 2519.78 MHz (279.98 * 9)
----------------------------------
MB Brand :
MB Model : nForce
NB : nVidia nForce3 250 rev A1
SB : nVidia nForce3 MCP rev A2
----------------------------------
RAM Size : 1024 MB
RAM Freq : 280 MHz
RAM Type : DDR-SDRAM Dual Channel
RAM Ratio : CPU/9
RAM Timings : 2.5-4-4-8
----------------------------------
Slot 1 : 512MB (PC3200)
Slot 1 Manufacturer : Corsair
Slot 2 : 512MB (PC3200)
Slot 2 Manufacturer : Corsair
won't push it any further cuz i'm happy with it at 50degrees on load and i'm not into OC for the sport.
Hello.Quote:
Originally Posted by dng29
for 320HTT 1:1
BIOS: 510-1
RAM: OCZ Plat. Rev2 (TCC5)
DRAM Frequency: 200MHz
CPC : Enabled
tCL : 2.5
tRCD: 4
tRAS: 7
tRp : 3
tRC : 14
tRFC: 16
tRRD : 3
tWR : 3
tWTR : 2
tRWT : 3
tREF : 3072
tWCL : 01
Dram Bank Interleave: Enabled
DQS Skew Control : Auto
DQS Skew Value : 255
DRAM Drive Strength : Lvl 8
Dram Data Drive Strength: Auto
Max Async Latency : 8
Read Preamble Time : Normal
Read Preamble Time : 5
Idle Cycle Limit :256
Dynamic Counter: Enabled
R/W Queue Bypass : 16x
Bypass Max: 7x
32 Byte Granulation: Disable
Ram @ 320mhz
CnQ off
LTD 3x
LTD Voltage : 1.3 V
Chipset Voltage : 1.6V
Ram Voltaje: 2.8V
I hope that this can help it. Also I recommend to read this post:
http://i4memory.com/showthread.php?t=327
Until Soon
Quote:
Originally Posted by LANero
wow i didn't know that TCC5 can run at that high speed with 1:1 ratio sync. thanks for the setting. i'll try it on mine and see if my memories will like it. thanks for the link too.
Keep in mind not all ram sticks are created equal ;)
But thanks for the settings Lanero, if my ram works that high i could cast off my 166 divider and say hello to bandwidth :)
Alrighty. I received a 3500+ CBBLE 0512 DPAW yesterday. So far so good. I can pass 8M Super Pi up to 2.9ghz (290x10 1.55v) If it passes 8M then it will do everything I need without a hiccup. 32m is just to damn long!;)
I can get a suicide shot at 3ghz but I can't do much other than browse. Not to bad for a second hand cpu that I bought here for a great price!!! I have only had one other 2.8ghz+ cpu and it was a 3500+ claw that ran to damn hot. I am psyched to finally get a low voltage cool running 2.9ghz cpu!;) :toast:
There is no problem.
It is the configuration that better result has given me, can not reach results such but I believe that it can help to improve a little.
It is a pleasure to be able to help.
Until soon friends
3500+ LBBLE 0519DPHW results for this one isnt promiseing . did 2300mhz at stock voltage. required 1.47 to do 2400mhz . 2500 failed prime even up to 1.55 which is max limit of this board. max temp at 1.55 was 54c under load ,
Jen
I've always wondered if part of the reason some cpu's do so much worse than others is because of really bad IHS contact. I know that isn't the whole story but it may play a part.Quote:
Originally Posted by Jen
Could be when i took the IHS from my cpu there was a spot of 2x2mm on the center of the core that was without any thermal grease and the temp are much lower now + it OC about 50mhz more with the same voltage :toast:
I just took the IHS off my chip the other night and noticed that there wasnt any thermal grease in the middle of the core. But by removing the IHS I was able to go from HTT 326 to HTT 334 my heat dropped that much it went from 34-35c idle to 30-31c and doesnt even go over 40c under load. I also put some as5 on the chipset and it sits at 41c instead of 48c.
http://valid.x86-secret.com/show_oc.php?id=26948
hmm I think I have the same issue as you...was it hard to take it off, how did u do it. and is it easy to crack the core, cuz i got a big heatsink.
good work 007!!! very nice
Quote:
Originally Posted by njkid32
Thanks guys, it was a pain but I took my time and just worked a razor back and forth till I broke through the glue.
I have the Big Typhoon and it may be big but its not heavy and doesnt really put extra stress on the core. I was just careful how much I tightened it down. It was the best thing I have done yet.
WOW men.Quote:
Originally Posted by njkid32
Great job.. :clap:
Congrats.
I have the same week GPBW venice. Right now, maximum 3dbenchable is about 2.86 @ 1.63 volts with Big Typhoon cooling. I'll try removing the IHS and see if I can get the same excellent results.Quote:
Originally Posted by njkid32
wow njkid, nice processor, nice clocks and good job with the IHS. That really makes me want to remove my IHS. With only 1.58 volts i'm getting load temperatures of 53C and my cooling isn't a slouch.. soon it's going to be water but then it would still help. I'd kill for +50 Mhz! :D
I've just built my first A64 rig
3000+ LBBLE 0521APMW
Abit AN8 Ultra
Corsair 4400C25
9 x 278MHz 1:1, 1T, Stock HSF with stock volts :toast:
Is it stable you ask? look here ----> http://www.xtremesystems.org/forums/...482#post950482
Congrats bugeyes :)
It seems to me that you do not need a week 17 to get up there :D
Yeah it's all luck, I never go out and look for a so called magic stepping / week.
I still have room to push it a little more, just don't want to give it more than 1.4 vcore untill I get better cooling. I just love these cheap 3000+ and getting a free 700+MHz
second that, we all do! ;)
http://img99.imageshack.us/img99/9076/3015mhz5mt.jpg
More Mhz but needed a lot more volts for it
:(
NEED WATERCOOLING...
Is it safe to remove IHS and put XP90 on it ?
Or should i leave 7000B-alcu ?
I did a burnin last night and now I am able to run 1.68v instead of the high 1.76v to get 3GHz. I didnt expect to be able to drop it so much. That makes me think I didnt need that much to begin with. Do you guys think if I go with a dangerden water setup I will be able to go farther?
Nice OC Absolute_0 I was able to boot at HTT 336 but I dont know how stable she was. I just tried it to see if I could do it. But your lookin good there will low volts!!
Can anyone tell me if is this a good stepping ?
3000+Venice CBBLE 0521-CPDW I just got it about an hour ago, but before open it and test it, I like to make sure I got the good stepping, Thank you !
si tu le teste pas tu ne pourras pas savoir si c'est un bon step ou pas. car même dans les meilleurs step ils ya des bon et des mauvais... regarde les 0517BPEW par exempleQuote:
Originally Posted by AMDfan
if you don't test it you couldn't know if it is a good step or not.
good step can be good or not like 0517BPEW...
:owned:Quote:
Originally Posted by starostise
:banana:
french users :toast:
Thanks alot HomeBoy ! I don't know if we can write in French overhere :( :confused:Quote:
Originally Posted by starostise
Mine was lacking TIM in the center too so i saw about the same temp drop...Quote:
Originally Posted by njkid32
It takes 1.8v+ for me to bench at 3ghz though, still doesn't hit 40c though :cool:
unless you guys translate into english also I think it should be alright ;)
How many volts are you using for 2.94 and 3.06?Quote:
Originally Posted by njkid32
What about the hieght drop from removing the ihs, do you need to shave the socket, i have an xp90 and it has a big base that sits over the socket.
I was running 1.54v at 2.94 after a 24hr burnin. Originally I was running 1.76v at 3.06 but now I have lowered to 1.68v but I am not sure how stable she is right now with the volts that low so I am going to run some tests and see. She was prime stable at 1.76v (which I didnt get a ss) but I am not sure about now. I am going to run prime again. Also what kind of volts are people running is running 1.76v way to high? For Air...Quote:
Originally Posted by Absolute_0
It looks like its almost resting on the socket but not quite. Its on there tight but I didnt go crank it down or anything.Quote:
Originally Posted by 4rory
Right now its about 110 here in Arizona and I have the a/c on 78 and my comp is still running at 32-33c. NICE
1.76V is a lot for air, not something i would try, even with good temps.
Really, I thought if the temps were good then you could go over 1.7v but not to far over.Quote:
Originally Posted by Absolute_0
1.76 is high voltage, and on air it's really high. Most people agree not to go over 1.7 on air cooling. Most likely the chip won't die but over 1.7 is the danger zone. I was only at 1.664 when i did that suicide shot because i don't want to do more voltage until i get my watercooling. Anyway, i was completely unstable at 3015 and when i tried the next setting in clockgen, 302x, it blue screened. However, i am fairly sure it was my memory giving out and not my CPU, as i forgot to loosen my memory timings so my OCZ was doing DDR550 at 2.5-3-3-7 and i have to run 2.5-4-4-8 for those speeds.
hello guys
This is my 3200+ 0519 EPKW with stock cooling.
http://img153.imageshack.us/img153/7...vstable4of.jpg
Nothing wonderful, but is not the worse one either than I have had.
I hope that with Big Typhoon it can improve it.
Until soon
That's pretty good on stock volts. You'll be able to increase the voltage with the Big Typhoon and make it fly.
very good for week 19 :toast:
my 0517DPMW on stock voltage, it was stable OCCT at 2700MHz at 1.34V, i just tested two sp2004 at the same time.
one with small fft and one with large fft:
http://img301.imageshack.us/img301/6...dpmw8ut.th.jpg
now i'll test at 1.34V primestable :banana:
EDIT: prime do not pass at 1.34V
EDIT: i tryed blend mode :
http://img305.imageshack.us/img305/1...pmw29ok.th.jpg
OC looks really nice! Volts are really low you may just have to bump it up a little bit.
thanks boys :toast: .
In ahead I need there to increase 0.025v by each 50mhz:slapass: .
I will continue proving and raise results.
@ starostise
That if it is an excellent chip :slobber: .
Congratulations man. :clap:
i have a 3000+ LBBLE 0516DPJW seems i cant boot past 2.5ghz maybe its the mobo anyone else having problems with this stepping?
I had a 0516CPBW that needed 1.5v for 2.4GHz :stick:
And still some people say week 16 is good... at least I know how good they are...
I'll tell you guys that at first I wasnt able to boot at HTT 334 but went back into the bios and changed the tref setting and pow no more bsod's. For some reason I had to change from 2048 to 4672 in order for it to boot. That should tell you something. Its all about the mem timings. At least I think so.
Thanks njkid32, that's really good to know. When i was doing really high HTTs a while ago i would get lots of BSODS, maybe that will help.
Your welcome! Its funny I found a list of tref settings and cant get any of them to work. I tried all of them and bsod's all day. So what I did was lower everything and start in the bios at the first tref setting and worked my way down. When I was able to get into windows I opened A64 Tweaker and looked at the setting. After testing and testing I found that 166 7.8us (4672) was the fastest for my ram but memtest didnt like it. But it only gave a few errors and the funny thing was that windows loved it. That setting made windows more stable. But I am still testing so we will see what the outcome is....
0388= 100mhz(15.6us)
0516= 133mhz(15.6us)
0648= 166mhz(15.6us)
0780= 200mhz(15.6us)
---------------------
0908= 100mhz(7.8us)
1032= 133mhz(7.8us)
1168= 166mhz(7.8us)
0016= 200mhz(7.8us)
---------------------
1536= 100mhz(3.9us)
2048= 133mhz(3.9us)
2560= 166mhz(3.9us)
3072= 200mhz(3.9us)
---------------------
3684= 100mhz(1.95us)
4196= 133mhz(1.95us)
4708= 166mhz(1.95us)
0128= 200mhz(1.95us)"
Week 16 is pretty bad for me... it applies to Winnies and Venices.
[]'s
Thanks for the info njkid32 :toast:
My 3200 0520BPMW will not, under any circumstances go over 290 HTT :mad: , I have tried every bios available with no joy so either it is the mobo, my TCCD or the CPU and after reading your post, maybe Tref, so I will try your advice :)
This excellent 3000+ 0517EPMW which I just bought has good performance I have ever seen.
3000+BP 0517EPMW 16E50463
300*9 1.360v
cooler: Tt Sonic Tower 12CM fan*1
idle: 34~36c
full load: 39~41c
please write vcore set in bios not cpu-z or smartguardian !
going to bench my venice from week 12 again. Got another waterblock and i think my ramtimings :banana::banana::banana::banana:ed up my oc.
well folks here's a little update on my adventure in ocing my week 19 3200 venice. I finally decided to run prime95 because previous tests in prime95 failed miserably. This time around I didn't use the regular prime95, but the modified prime95 with the green GO box. I hope you know what I'm talking about. To my surprise this prime95 ran fine for 6+hours at 2850Mhz with mem divider at 180Mhz and vcore of 1.68 as reported by bios. Here's the kicker, i set ldt to 4x so with mem divider my memory is 259 as reported by cpuz. if i do the math right here 259x4x2 = 2072Mhz htt. That's slight over the specs of 2000Mhz htt. i used pretty tight timings for memories. btw, these are g.skill dual channel sticks. I got a screenshot of prime95 and will post when i get home from work. I'm thinking of dropping the vcore down a bit and see what will happen.
My AMD Athlon64 3800+ CBBLE 0504EPMW Watercooling
http://img.villagephotos.com/p/2004-...7/SuperPI2.JPG
Real nice OC sdkevin! What are your temps and is this the limit of your chip or can you go higher? I almost picked one of those up a couple of weeks ago is why I ask.
sdkevin: try to tighten your memory timings, 29s is not bad, but it can be better. i get 29s with 1M superpi with my 3200 venice at 2900Mhz. is this 24/7 stable or just for show?
Summer here and it's hot so BIOS temp around 43C load, I'm using it for 24/7 I don't mind to bother tighten the memory timings since I need to wait my OCZ PC5000 back from RMA
anyone given the 0523 week venices a shot yet?
i finally found a shop close to my home where they wanne chk the stepping for me
they just received about 10x 0520 GPEW Venice 3200+ CPU's...
been lookin/googlin around, but cant find much about this stepping yet... anyone know if theyre any good?
is there also some other code of the stepping that i should pay attention too? (since they all have the same 0520 GPEW code allready :/)
If you can Mastakilla try and find one same as my 3200 in my sig, bloody awesome :D
2.8 Gig torture+ stable with only ~ 1.51 Vcore reported in windows :woot:
the first post 3000+ Venice stepping seem like no update pass 2months ago...
:(
yea it's been a while since teh last update :(
Just got my 3200+ LBBLE 0519 APAW 10 minutes ago i'll slap it in and report back.
got alot of testing to go and some ram issues but ill do my best.
this will be water cooled.
i dont see any week 19 in the list if anyone has any results thus far for these post'em
Gl :)
2.5ghz 1.39v
250mhz 1:1
3x HTT
30 Idle
37-ish load under Prime95
did the big Overclocking god FINALLY smile on me ? Did i get a good one ? ohhh let us pray on this and return in a while with some more results!
GJ Lestat
Waiting for more Mhz! :toast:
With those temps you certainly have alot of headroom for voltage.
GJ Lestat I hope you got a good one! Maybe 3GHz on air;) Just take it slow! I know when I got my chip I was going higher and higher on the first day but it really didnt like it. It took me at least 1mo to get a good oc.
yeah i was just thinking about the whole "break in period" i figure tonight i'll Fold and/or Prime and let her get beaten up real good ;)
2.6ghz 1.45v
260mhz 1:1 but really loose ram cuz this OCZ stuff needs more volts and the board only gives 2.85 and i cant afford a ddr booster right now.
speaking of ram, this is something ive never asked anyone. and i know the answer or atleast i would like to think i do.
1:1 you need to raise the voltage as you go (atleast on non TCCD stuff) but when you run it on a multi say 166mhz the voltage dont matter does it until you get your ram back up to its rated speed.
so basically dropping the ram to 166 i can pretty much throw the lacking vdimm out the window for a while cant i ? since yout not really running the ram at lets say 260mhz its actually... errr ... 212 ? i think the math calculates out to ?
i was hoping i wouldnt have to make such a jump from 2.5ghz to 2.6ghz in cpu voltage but hey its still much less than my newcastle which wouldnt even do 2.6ghz.
I'd go with a blood sacrafice of a Noob to guarantee an awesome overclock. Why take a chance on quiet prayer when your victim's screams would be so much louder? ;)Quote:
Originally Posted by Lestat
i couldnt agree more.Quote:
Originally Posted by gundamit
well the ol lady is on the rag so there's blood there.
ok well T.M.I. HAHAHA i love being the sicko of the bunch.
ok well i am having an issue here and i must assume its the mobo.
right now it appears as if 2.6ghz isnt Pi stable. im getting Not convergience error. so i upped the voltage to 1.475 then 1.5v
ok now the bug... i have the bios set to 1.475v yet its only 1.45v in windows. i though ok just goofy reading. so i am at 1.5v yet its still being reported as 1.45v in windows by speedfan cpu-z and core center.
wierd this board has never had issues going up to 1.7v ... hhmm..
Is this some sort of a Venice bug ?
CPU-Z is actually jumping from 1.425 to 1.45 i HATE seeing that but seems like my Vcore is locked ?
If i apply the vcore with clockgen it wont change either.
im having the same problem. i just flashed to the latest bios too... wierd. anyone else??Quote:
ok now the bug... i have the bios set to 1.475v yet its only 1.45v in windows. i though ok just goofy reading. so i am at 1.5v yet its still being reported as 1.45v in windows by speedfan cpu-z and core center.
wierd this board has never had issues going up to 1.7v ... hhmm..
Is this some sort of a Venice bug ?
CPU-Z is actually jumping from 1.425 to 1.45 i HATE seeing that but seems like my Vcore is locked ?
If i apply the vcore with clockgen it wont change either
peace perc,
Are you testing with a Digital Multi-Meter? Don't trust anything else.
Perc i found the issue.
once you hit 1.45v you need to use the % over VID like 3% 5% and so on.
so right now i am at 1.5v + 3.3% over VID
cpu-z says its like 1.55 ... maybe im using 5% i forget.
CPU-Z is showing some really floaty voltages i really dont like that. 1.52 then it goes 1.536 then 1.55
im also at 2650 1:1
32c idle 44c Prime95 load
i need a better 939 AGP based board. grr anyone got any suggestions.
dfi nf3 ultra-d or msi k8n neo2 platinumQuote:
Originally Posted by Lestat
i got the NEO2 not near enough vdimm
i was looking at the ultra d last week but wasnt having much luck find alot of good stuff to say about it. It's like a mobo DFI put out and not many people have it.
ill have to look around some more.
seems like up to 2.5ghz im ok with default voltages but anything above that i really gotta crank the voltage.
but then again i just got it 8 hours ago so there is alot of break in period left.
what do you guys suggest i use to really pbreak it in properly just let prime run non stop or fold non stop ?
Has anyone else found the burnin effect to actually work with Venice chips :confused:
When i first started with this 0517DPMW it would hardlock at 2775Mhz in 2 systems.
After 1 day of stressCPU @ 1.55v 2700Mhz, it is now stable at 2820Mhz and hardlocks at 2830Mhz
After 2 further days of stressCPU/SuperPI and 1.55-1.65v, the CPU now does 2930Mhz SuperPi with no sign of hardlocking :stick:
http://users.bigpond.net.au/aokman/wowie.jpg
3000+ APJW aircooled
http://img.photobucket.com/albums/v7...03-2-hours.jpg
Quote:
Originally Posted by orig3n
maybe i'm not looking carefully, but could you pleaes give us the specs on your venice. 3000 or 3200? week? code? cooling? the reason i'm asking is I'm trying to do what you're doing with stresscpu. my 3200 venice can do 2800Mhz fine, but can't go any higher. i can boot into winxp at 2850Mhz and run some superpi benches, but it's not 100% stable. I can also run it at 2900Mhz and run 1M superpi and that's it. this is on an xp-120. right now i got the cpu burning with stresscpu at 2800Mhz. i'm at work and hope that it doesn't crash when i get home tonight. 2900Mhz 100% stable will be a dream come true for me if this method works :).
Its a 3200+ 0517DPMW :toast: 1.64v above 2.8Ghz
Quote:
Originally Posted by orig3n
could you please pm me your bios settings :). is that 2930Mhz 100% stable 24/7 for you?
2900Mhz fully stable now, 2930Mhz superPI :banana: