Printable View
Quote:
Originally Posted by Leeghoofd
I just like to get the 'hang' of the board before benching it Leeg. "You can only see the scratches in your car once you wash it yourself" :yepp:Quote:
Originally Posted by zsamz_
So far the board is very steady and darn fast. Tested 600x8.5 yesterday and passed 3hrs Prime95 with my new settings.
So I moved on to 600x9 :devil: Let's see how this will fair.
Here some more stability tests:
Keep in mind my Load-Line Calibration is disabled and your CPU may require less volts all around then mine.
Here's the BIOS [E8600x5100Mhzx600x8.5xStable]:
Code:Extreme Tweaker
Ai Overclock Tuner [Manual]
OC From Memory Level Up [Auto]
FSB Frequency [600]
CPU Ratio Setting [8.5]
* CPU clock skew [Auto]
* NB clock skew [Auto]
FSB Strap to North Bridge [266]
PCIE Frequency [102]
DRAM Frequency [1805]
DRAM Command Rate [Auto]
DRAM Timing Control [Manual]
1st information
CAS# Latency [7]
RAS# to CAS# Delay [7]
RAS# PRE Time [6]
RAS# ACT Time [21]
RAS# to RAS# Delay [Auto]
REF Cycle Time [Auto]
WRITE Recovery Time [Auto]
READ to PRE Time [Auto]
2nd information
READ to WRITE Delay(S/D) [Auto]
WRITE to READ Delay(S) [Auto]
WRITE to READ Delay(D) [Auto]
READ to READ Delay(S) [Auto]
READ to READ Delay(D) [Auto]
WRITE to WRITE Delay(S) [Auto]
WRITE to WRITE Delay(D) [Auto]
3rd information
WRITE to PRE Delay [Auto]
READ to PRE Delay [Auto]
PRE to PRE Delay [Auto]
ALL PRE to ACT Delay [Auto]
ALL PRE to REF Delay [Auto]
DRAM Static Read Control [Auto]
DRAM Dynamic Write Control [Auto]
> DRAM Skew Control :
DRAM CMD Skew on Channel A [Auto]
DRAM CLK Skew on DIMM A1 [Auto]
DRAM CLK Skew on DIMM A2 [Auto]
DRAM CTL Skew on DIMM A1 [Auto]
DRAM CLT Skew on DIMM A2 [Auto]
DRAM CMD Skew on Channel B [Auto]
DRAM CLK Skew on DIMM B1 [Auto]
DRAM CLK Skew on DIMM B2 [Auto]
DRAM CTL Skew on DIMM B1 [Auto]
DRAM CTL Skew on DIMM B2 [Auto]
Ai Clock Twister [Auto]
Ai Transaction Booster [Manual]
Common Performance Level [9]
Pull in of CHA PH1 [Disabled]
Pull in of CHA PH2 [Disabled]
Pull in of CHB PH1 [Disabled]
Pull in of CHB PH2 [Disabled]
(-- Manual --)
EPU II Phase Control [Auto]
*** Please key in numbers or select voltage!***
CPU Voltage [1,743]
Load-Line Calibration [Disabled]
CPU PLL Voltage [1,60]
FSB Termination Voltage [1,40...]
CPU GTLVref(0) [+40]
CPU GTLVref(1) [Auto]
CPU GTLVref(2) [Auto]
CPU GTLVref(3) [Auto]
NB GTLVref [Auto]
North Bridge Voltage [1,72]
DRAM Voltage [2.14]
NB DDRVref [Auto]
DDR3 Channel A Vref [Auto]
DDR3 Channel B Vref [Auto]
South Bridge 1.5 Voltage [1,57...]
South Bridge 1.05 Voltage [1,09...
******************************************
CPU Spread Spectrum [Disabled]
PCIE Spread Spectrum [Disabled]
Some SS's or it didn't happen:
http://img526.imageshack.us/img526/6...95small.th.jpg.........http://img692.imageshack.us/img692/7...600occt.th.jpg.........http://img685.imageshack.us/img685/6...test100.th.jpg
I did manage to work on a nice 5.4Ghz (600 x 9) config and it's working out great so far, problem is to Prime this I need better cooling:
http://img526.imageshack.us/img526/9...0spi32m.th.jpg
very impressive Jor3lBR, makes me want to get another REX+dualcore for some fun:D
Thanks Radaja! Man where is that god like E8400 of yours man?!Quote:
Originally Posted by radaja
very nice Jor3lBR. it's rare to see a 5ghz+ chip not crashing on a stability test. what was the cooling?
Thanks WhiteFireDragon :up:Quote:
Originally Posted by WhiteFireDragon
Cooling used was a modest OCZ Cryo-Z single stage. This is more for 24/7 use I'm moving on to a Dual Stage just for benching and the Cryo-Z is up for SALE.
i sold it allQuote:
Originally Posted by Jor3lBR
i got his chip, but my dfi doesnt want to play and ant i dont have the money for an rex but damn i want 1Quote:
Originally Posted by radaja
REX retails at 170 euro's at Alternate mate, what the heck are you waiting for !!! Sell the DFI and don't look back :p
your ut should do 4.5 easyQuote:
Originally Posted by kamieldehond
just try with 2x1 memory ;)
Quote:
Originally Posted by Leeghoofd
Ill give my dfi 1 last try and if it still will not play ball ill sell it and get me a REX :) Doubt ill get much money fot it tough
What is the best memory for the REX? I want to run 4gb
wanna trade:DQuote:
Originally Posted by kamieldehond
what do you have in mind? plz send me a pm if you are seriousQuote:
Originally Posted by zsamz_
Very nice work Jor3lBR, the REX is the most fun board I have ever used bar none. You will have a great time with it for sure. Makes me want to dust off mine and buy a PSU for it so I can bench again.......
Thank you Cryptik don't hear from you in a while!Quote:
Originally Posted by CryptiK
A lot of your posts here and on i4memory helped me to get this board 600x8.5 prime stable :up:
Too bad I run out of cooling power to try to go further, it's a very solid board and easy to use. I will get it cold this month and put some results under it's belt before I part away with all my 775 stuff.
That makes two of us. :DQuote:
Originally Posted by CryptiK
I never went back after mine died though, got a refund and went AMD again which is lots of fun clocking too but not as much as the RE.
Pushing FSB and memoryclocks on this board is addictive stuff. :)
Good to hear some of my info came in handy. You are going very well so far, will be very interested to see how you go with a better phase unit or LN2.Quote:
Originally Posted by Jor3lBR
I've been away from things for a few months now, had to build a PC for my GF out of some gear I used for benching and haven't replaced it. Built an i7 system to use which I don't bench, and have been pursuing some other things. I still drop in from time to time to see what's happening here though, I do miss it.
That's too bad, you were going really well with it too before it died. It's good that you're enjoying the AMD stuff though, and that's what's important.Quote:
Originally Posted by Zeus
http://www.upload.ee/image/336373/08.01.linx.png
some twiks and 490FSB stable.great mobo!!!!
Nice work there rurik. The hard part will probably be getting Prime Large FFT's stable at high FSB with 2 x 2GB. Your NB is on water though, so you should have a good chance.
and Prime95 too.:)Quote:
Originally Posted by CryptiK
http://www.upload.ee/image/336918/26.12.prime.png
Exactly my feelings, AMD is fun, BUT S775 is even more fun.... so, should I buy a REX? :DQuote:
Originally Posted by Zeus
DON for the E8600 is a must and 9x600 stable and 10x600 with the proper cooling is possible :DQuote:
Originally Posted by Don_Dan
Daniel, if i had to choose a S775 board, this would be the one without a doubt!
Flip back a few pages and you see why i liked it so much. ;)
Go for it bud!
Quote:
Originally Posted by Jor3lBR
Thanks for the input, I'll buy one after my exams, Alternate has them for a ridiculously low price. :)Quote:
Originally Posted by Zeus
Very nice work there :up:Quote:
Originally Posted by rurik
If you have never played with a REX, absolutely, get one. They are really great boards.Quote:
Originally Posted by Don_Dan