**Official ABIT IP-35 Pro Review/Overclock/Guide Thread**

Quote:

---

Originally Posted by fatal_error

damn, just did the heatpipe mod and added a 80mm fan on top of the pwm area, 20mm fan on both the pwm and NB heatsinks. Now my PWM temps are improving, but the NB runs about 44c idle and 50~51 when im playing games like MOH airborne... Would that be ok for the NB chip or it may dmg it? =S

---

May I ask how you know the NB temp? Is that the system temp?:confused:

Quote:

---

Originally Posted by Knight

May I ask how you know the NB temp? Is that the system temp?:confused:

---

ya i believe so

Quote:

---

Originally Posted by Soulburner

No problems here, my main drive is a 150gb Raptor.

Ace, that's a damn good clock at stock voltage. I can't believe you have a quad doing that while my E6850 won't go over 3500 without upping the juice.

What's your Super Pi 1M at that speed?

---

i wish that was true!:) ...i think you read the vid from coretemp or cpuz 1.4 ver which is not the actual vcore...look at uguru..it was reading between 1.49 - 1.50v there about.

Quote:

---

Originally Posted by Knight

May I ask how you know the NB temp? Is that the system temp?:confused:

---

i believe the system sensor is in close proximity to the NB.

Quote:

---

Originally Posted by AstroCreep

Really? :( That sucks! I recently bought a Raptor X when they were on sale at Best Buy.

---

I got my two 74GB Raptors (16MB) early this year for $119 was gonna get 4 but thought i should get something else so I messed up there

Quote:

---

Originally Posted by Ace-a-Rue

2nd, i heard via the grapevine that WD Raptor drives are subject to errors on this newest version of the ICH9(R) chipset(s)....if you can swap out the drive with another type other than a Raptor, you might just get a higher overclock.

---

I get a RAID error now because I froze up w/ uguru and cpu-z:down:

Quote:

---

Originally Posted by Knight

May I ask how you know the NB temp? Is that the system temp?:confused:

---

no its not, the system temp is your overall case temp.

no way the nb runs at 28c lol

Quote:

---

Originally Posted by Alik4041

Having a problem that has been recently stated. Set my memory timings in bios to 4-4-4-12-1t. CPU-Z shows 2t. Memset doesn't have a command rate option which I'm surprised off. Does beta 12 support ACTUAL T1 command rate? Any information is greatly appreciated

---

I'm experiencing this too (1T set @ bios = 2T @ CPU-Z) with beta12.

I believe it's a coding glitch in beta12.

what bios are u using strange|ife? are you using HZs?

Quote:

---

Originally Posted by largon

I'm experiencing this too (1T set @ bios = 2T @ CPU-Z) with beta12.

I believe it's a coding glitch in beta12.

---

Well there is no performance gains either I don't think. In this thread, someone tested the difference between 2T and 1T on this board and the scores were identical...I'm blaming abit's bios right now :shrug:

Quote:

---

Originally Posted by Ace-a-Rue

a couple things that i would recommend:

3rd, try boosting your ICHIO 1.5v to 2.0v for a short time along with boosting your MCH to 1.7v for a short time to see if that steadies your overclock or allows you to go higher...if it does allow for a higher overclock or makes it very stable then you can back it down a notch at a time to find the sweet spot.

---

We just may have gotten somewhere now. I tried your settings and got an instant shutdown when enabling them in uGuru. So I backed the MCH to 1.65 and the ICHIO to 1.81 with vCore at 1.425 which gives me 1.36 at load ( I really need to do the volt mod ). These settings got me 7 minutes of Small FFT's before Core 2 crapped out. So I upped the vCore to 1.4925 and got an instant shutdown upon firing up Prime. This thing just hates high voltages. So I just went to bed ans tossed and turned thinking about it. This morning I got up and went back to the first settings of MCH 1.65, ICHIO of 1.81, and vCore of 1.425. But this time I set the CPURef's to 70% instead of 67%. I am now almost 2.5 hours into Small FFT's without a whimper from it this time. I am beggining to like this thing now :up: Thank's Ace for the suggestions.

Pntgrd what FSB are you at...I have found that the stock 1.25v is enough juice for the NB up to 460fsb 1:1 (DDR2-920) and 400fsb 4:5 (DDR2-1000). I haven't tried any higher so I really don't know at which point you need more vMCH.

Quote:

---

Originally Posted by Soulburner

Pntgrd what FSB are you at...I have found that the stock 1.25v is enough juice for the NB up to 460fsb 1:1 (DDR2-920) and 400fsb 4:5 (DDR2-1000). I haven't tried any higher so I really don't know at which point you need more vMCH.

---

At what multiplier though? I can do 8x400 easy at stock volts. It's 9x400 where I have stability issues. Anything above 3.2 to 3.3 requires more voltage. My chip has a Vid of 1.2125, what's yours? That could make a difference. There can be all kinds or reasons. I still think I may have an issue with the heatpipe maybe being too tight. I know I cannot go very high on voltages as I just get a shutdown. I should have the fans I want to try on the Gemeni II on Monday. I am going to remount the heatpipe when I do the hs change just to make sure. I did the mod before I ever installed the board so I don't know what it could do before the bolt job. I even changed psu's thinking I that maybe i was having voltage supply issues from the symptoms. I now wonder if my OCZ was not to blame. I can't find out now as I ahve already swapped it out for 2 more sticks of 1066 Tracers, whick I need to install also. Or it could be that I just have a pickier board than most. Must be a female, huh.

E6550 @ 460x7 1:1 on IP35 and E6850 @ 400x9 4:5 on IP35 Pro. I did not have to raise vMCH in either case, all I needed were vcore and vdimm. This is not the max for either system so I am not sure what point I would need more volts to the MCH.

Actually raising the MCH seemed to cause instability for me.

Could also be a difference in the Quad needing more that you Dual :shrug: . I just know I am glad to see it finally Prime stable at 3.6. I bumped the ram up to 1:1.2=960 and tightened the timings to 4x4x4x12 and it's been Priming away for 2.5 hours now. I will start lowering the voltage to find the sweet spot after redoing the heatpipe and changing the hs. I want to see the effect of the Gemini on the getting much more airflow around the top of the board since it sucks so much with the Ultra120. If it doesn't work I will go back to the Ultra.

I think I need 1.33v MCH to get it stable at 8X400 FSB :confused:

Alright, well i am back with my HDD problems. I tested the harddrive i was going to RMA and that was not working direct sata into my board, in a hdd external enclosure and it worked fine!
I was able to transfer at normal speed and do everything as I should.


I also took the drive out of my external and put it direct sata into the board and it was showing the same problems as the supposed broken one!

Now I think it may be the board!! what should I do, is there any way to try and configure something in bios??

Quote:

---

Originally Posted by Soulburner

E6550 @ 460x7 1:1 on IP35 and E6850 @ 400x9 4:5 on IP35 Pro. I did not have to raise vMCH in either case, all I needed were vcore and vdimm. This is not the max for either system so I am not sure what point I would need more volts to the MCH.

Actually raising the MCH seemed to cause instability for me.

---

What type of instability were you experiencing?

Quote:

---

Originally Posted by strange|ife

no its not, the system temp is your overall case temp.

no way the nb runs at 28c lol

---

NO...we said the temp sensor is probably in the vicinity of NB...before i did the heatpipe mode the temp was a lot higher for system since the heat coming off the NB was not really entering the pipe system..it was staying right there and permeated the surrounding area.

I can't for the life of me get these 6400HZ sticks to post I am SO PISSED OFF! I have tried everything - do you think I should RMA good sticks?

Quote:

---

Originally Posted by TheGoat Eater

what bios are u using strange|ife? are you using HZs?

---

Bios 11

yes i have 4x1gb pc6400 GBHZ

being bored this weekend, i decided to load up everest memory READ/COPY. with 1T enabled over 2T. I could have sworn last time i did this test i gained 600 or so points..maybe it was something diffrent, it was a while ago. anyway i took some screencaptures.
iam running 451x8 memory@902mhz 4-4-4-12

2T:READ&COPY
http://www.imagehosting.com/out.php/t1143942_2T.jpg
http://www.imagehosting.com/out.php/t1143943_2Tcopy.jpg

1T:READ&COPY
http://www.imagehosting.com/out.php/t1143944_1tREAD.jpg
http://www.imagehosting.com/out.php/t1143941_1Tcopy.jpg

as you can see very very marginal gains to be had with 1T right :rolleyes:
now:rolleyes:
maybe everest isnt the best program to use?? for this sorta of thing.

3DMark2001 is still the best benchmark I have found to test different CPU/FSB/DDR configurations. Watch the framerate results for car, dragothic and the lobby tests, they are very sensitive to these changes.

Synthetic benchmarks don't carry much weight.

Quote:

---

Originally Posted by Knight

What type of instability were you experiencing?

---

In a couple cases I wasn't able to pass cleanly through Orthos until I lowered the vMCH on my IP35. That was at 460x7 1:1. Maybe every system is different, but neither of my boards needed more MCH volts. It may be the difference between a dual and a quad, I'm not sure.

Hi,

Sorry to hijack this topic but I'm having a little problem with my IP35 PRO/Q6600. Whenever I overclock (400X8 for example or even less. I know it's stable up to 420X8) and then run Everest to stress the system, my computer locks up when I run CPU-Z. If I don't run CPU-Z, everything is fine and I can browse the internet, etc. Has anyone seen this problem before and if so, any suggestions to fix it? Oh yea, I was on 11 bios when I saw this problem then flashed to 12 beta and still same problem. Thanks.