http://www.xtremesystems.org/forums/...35#post2777435
someone can try this mod?
http://www.xtremesystems.org/forums/...35#post2777435
someone can try this mod?
changed the nb cooler for an enzotech
will try the U120 Extreme soon (I prefer the Tuniq of course)
Have you tried giving them the voltage they need?? I had to set mine to 2.1vQuote:
Originally Posted by Dr. Wakeman
I had soem boot problems until I got the RAM up to 2.0v.Quote:
well maybe give it a try with a decent thermal paste.
btw does the board have bootbug ?
The problem is that the Cellshock Kit doesn't boot with default settings after a cmos clear. Can't change the ram voltage with a black screen.Quote:
Originally Posted by xploit
Boot with just the one stick by chance? Im guessing not..
1st. try with both sticks.Quote:
Originally Posted by eXclusive
2nd. try with one stick.
Result: no booting :(
I'd hate to say I'd get a known booting stick @ 1.9v in these boards and just getit off the egg.. I'm sure a single 1gb or 512mb stick even wouldn't cost more than $35. If you gotta friend that'd be better. I'm sure you could borrow his mem :p
hello.. i have problem to pass 510 fsb with this mobo..at 500 is full stable... but if i try to pass 515 te board doesn't boot. i have a 8400 that can do fsb 540 with mi asus p5k..
so i think that is the board the problems....can you tell me wich settings do you have used for 530+ fsb from bios?
thanks
CPU VTT 1,28V
Vdram 2,1V
CPU PLL 1,6V
NB 1,45V
DRAM timings auto other settings in Genie BIOS on AUTO
Beware my CPU is E6300 and supports a little more voltage then your E8400.
here we go...Q6600@3.8GHz (475x8) 110% primestable
14h and still running, good enough? :P DFI at his best!
System bench setup
CPU: Q6600 L740B269
Mobo: DFI LanParty DK P35 T2RS
Ram: Team Elite 2x2Gb PC6400
GPU: Oldschool Vanta LT (aka RivaTNT2)
HD: Seagate 7200.10 250Gb Single-Plate
PSU: LCPower Arkangel 850W
Cooling: Thermalright Ultra-120 eXtreme lapped and "coin modded" + Scythe S-Flex SFF21F 1600rpms / ADDA fans for prime only
http://img120.imageshack.us/img120/5...67largecv5.jpg
Prime configs:
Q6600@3.8GHz 1.42/1.37v load
TeamElite 950MHz 5-5-5-15 1.92/1.90 load
http://img207.imageshack.us/img207/1433/prime13hby2.png
As u can see all bios parameters are default, including FSB VTT e NB, really good, since is the first time i saw on DFI DK, 100% stability for >450fsb on default :up:
Very nice overclock Prelim :up:
This is one of the first quad oc's that replicates what Windwithme initially did. You have a very good low volting cpu there. ~0.05V vdroop nice. What I find interesting is that you say that all BIOS settings are default.
Could you post your BIOS settings?
Does your RAM use Micron D9GMH IC's?
yes, but this one absolutly stable....not 30min prime with large FFT :PQuote:
Originally Posted by Sailindawg
i have my doubts 500fsb is possible, having it primestable. My board doesnt even boots 500fsb on default settings :(
my bios settings:
http://img411.imageshack.us/img411/8...argenu2.th.jpg
http://img442.imageshack.us/img442/7...argewl8.th.jpg
http://img442.imageshack.us/img442/1...argeno6.th.jpg
http://img442.imageshack.us/img442/5...argeil7.th.jpg
i forgot to change one parameter, only now i check it; FSB VTT default is 1.2, my mistake. maybe is stable too at 1.2v :up:
my ram isnt micron D9, if so i was at 4-4-4 :P
team elite can have many dif IC´s, such as Epida and low volt chips. dont know exactly that i have, since i never pull out the spreaders :/
well , after my "peasant" MSI P35-FIR i have Dark T2 ;] so far ....
http://img352.imageshack.us/img352/6048/55911675iy1.jpg
Yes, excellent work! That's what caught my attention. 475 fsb with a quad is about as good as it gets.Quote:
yes, but this one absolutly stable....not 30min prime with large FFT :P
Thanks for the screenies!
Well look what have done with DFI and Quad
Dude....that's freakin noice!! Can you run blend and keep it stable? I have seen others run small FFT just fine but when they try blend it reboots on them.Quote:
Originally Posted by Prelim
THAT is sick!Quote:
Originally Posted by Vivio
disabled two cores.....how is that a quad? clock it with all four cores.Quote:
Originally Posted by Vivio
LOL. Good eye.Quote:
Originally Posted by jimmyz
good eye jimmy!
my pic is 14h Prime Blend :up:Quote:
Originally Posted by GripS
Can you host SG pack? Its' really nice and esy to readQuote:
Originally Posted by Prelim
Thanks
:)
SmartGuardian skin here:
http://freenet-homepage.de/Demoria/S...background.rar
enjoy :up:
I have set in BIOS VTT 1,22V, but if I test the CPU in Orthos, the VCPU is 1,28V. So the board overvolts about 0,06V. How can I make the board to not exceed the value I've set in BIOS?
How can I limit the Vcore? In BIOS there's CPU VTT and CPU special add, there are more settings related to Vcore?
Do you have similar problem?