Will try both settings.Quote:
Originally Posted by eva2000
Have someone had any stability problem with them?
Printable View
Will try both settings.Quote:
Originally Posted by eva2000
Have someone had any stability problem with them?
Any news of the socket 939 DFI board?
What are good optimal timmings for this board to really perform? 2-2-2-5-10-16 ?
(I'm trying to get to 30k on 3Dmark2001) Is it necessary to run 1T also ?
@ TinTin:
It seems to look like you have the same version of the 3200+ as me...what is the highest overclock you have gotten on it. I can't get anything over 2.337. I want to get 2.4 or more. I have a strong feeling it is my memory that is the problem though. Please help me out here.
In my opinion 1T is a must. You can try 2T but will need much more mhz to obtain the same bandwidth.
In one of the first pages of this thread bigtoe did said he was running 2-2-2-0
Altough 0 supposed to be the same as 5 the last one was giving hims some stability issues.
After several testings this weekend on the 250-270 FSB range I couldn't get my system PRIME stable with more than 250FSB (tried 1.7vcore and till 2.9vdimm). It ran SuperPI, 3dmark without crashes and while running prime the system was stable (win didn't crash) but prime always failed.
I think the problem is with the mem. Maybe 2 x Double sided 512 ADATA PC4000 is too much for the memory controller.
Now I'm back to 250 with:
2.5-4-3-0 2.7V (2.7 was the minimum stable Vcore)
R/W Queue Bypass 16x
32 Byte Granularity 4 bursts
Newcasttle 2200@2500 1.55V (if 100% stable I'll try less Volts)
IIRC, Tony/Bigtoe says for 512MB sticks increase drive strength to 2 ?
Thought I would give you guys a helping hand reaching ddr600 with the 3200 Plat rev2...this is just a good place to tweak from and should be stable if your dimms are pretty good clockers.
http://www.ocztechnology.com/upload/...0/CIMG0058.JPG
http://www.ocztechnology.com/upload/...0/CIMG0059.JPG
http://www.ocztechnology.com/upload/...0/CIMG0060.JPG
hope that helps you guys clock that little bit higher than you may have already acheived.Remember this is 1 dimm only with 2 dimms 270ish is about the max.
hmm.....thanks bigtoe :)
i'll try them on my 3700EBs :D (2x512MB :wierd: )
so, how i meantion that, lowering bypass max, R/W Queue Bypass, and raising DRAM Drive Strength brings more oc-playground, right? :)
but, what is the DQS Skew Control? :confused:
but ok, i'll set my settings like yours and will see :)
Gee I guess I have another project for the evening :D
You back home yet?
Thanks Tony, Just what we've been waiting for!Quote:
Originally Posted by mad mikee
:toast:
I don't get it...
Put my RAM to 150, LDT to 2x multi to 6x, Vcore to 1.55V, Vdimm to 3.3V, chipset voltage to 1.8V.
Everything else was at auto.
Then i booted at 6x200 and increased HTT w/ ClockGen, brought it up to 270MHZ and tryed Spi 1M, no problem. :)
Then i set 271 and then 272 and it freezes. :confused:
I thought it must be ClockGen so went into bios, set HTT to 300 and it posted!
But then it said "detecting array" and rebooted.
So i went down to 290, same thing, then to 280, same thing but no reboot, had to reset Cmos. :mad:
Is my board maxing out at 271???
I had 2x256 sticks of HyperX pc3200 in slot 1 and 3.
Try using only one stick in slot 1.Quote:
Originally Posted by Zeus
What are your timings @?
I have the same problem, its the bios.Quote:
Originally Posted by Zeus
With the original bios i could boot in windows with 305MHz HTT with AUTO.
Now with 9/12 and 9/14 I cannot boot into windows with 275MHz > HTT (detecting array > reboot)
We need Oskar Wu over here.Quote:
Originally Posted by kakaroto
Mine clocks better with chipset at 1.6 then anything higher.
I'm pretty confused on that setting. I think 4 should be the most agressive 1 the more relaxed. No idea about AUTO. I'll try with 2 but is it 2 for 512 and ALSO for 2x512 ???
I think this would be the case of gamers that enjoy benching & OC ing
Running 2-2-2-5 with 3.3V but mem never came above 215MHz or so, shouldn't be a prob.Quote:
Originally Posted by RansoM
Mem does 260 easy with 3.3V
Man, that's a slam in the face, expected at least 300.Quote:
Originally Posted by kakaroto
Why is it whining about an array, i don't even have an array!
The original bios sux. :(
I want more HTT! C'mon bios doctors! :D
http://www.dfi-street.com/forum/show...&threadid=1597Quote:
Originally Posted by Zeus
From Oskar_Wu
Quote:
There are a lot of chances for bios code to access and write the cmos space ... No body knows what will happened to these cmos space when we are doing serious overclocking ... Once the system is not very stable but still try to write the cmos space data , the cmos data may be lost and cause the cmos checksum error ... Once the cmos checksum error , the bios code have to reset all setting to default in order to prevent a wrong cmos data cause the system never able to boot up again ...
Currently the HTT frequency is programmed after the RAID bios rom finish initializing ... The RAID bios rom will always try to initialize and see if there is raid setting in bios ... If there is RAID setting in bios , you will see the RAID bios screen ... If not , the system bios will quickly clear the screen , most of the times you will not see it ... But if you see the system stop at the raid bios screen when you overclock , that means the HTT programming sequence hang up and not able to clear the screen ... the system will reset it after a few seconds ... after three times of fail , there will be a prompt screen " Press F1 " ....
Guyz, I really appologize if this is off-topic a bit...
But my DFI board will be here this week, and I can't seem to find any PC-3700 EB ram !!! I'm starting to panic !! :(
Any suggestions or comments are appreciated...
I'd really like to get the most out of my 3200+ mobile A64, and this even if she feels like going to 2.7Ghz... just in case.. :)
find some BH-5 or ocz EL pc3200 rev 2 platinumQuote:
Originally Posted by SunTzu69
also the ocz pc3700 gold rev3 is good.
3500 and 3700EB has gone EOL unless we find IC's that clock as well as the C die we were using...if you can find it snap it up ;)
We do have a new 3500part coming which handles cas2 quite well but does not clock as well as the 35 and 3700EB...it is quite nice though ;)
If you are looking to run a gig on this board i would recomend the 3200Plat rev2 as this does clock well with 2 dimms, and exceptional with 1 but its not quite as fast as the EB with tight timings.
Would PC-3500 EB be as good or close to 3700 ? Please explain what I'm looking at if I want to get a 10x multiplier processor to 2.7 Ghz (3200+ mobile A64). I'm affraid I'll be limited with the 3500 and I might not get quite as high on the FSB as I need to get for my cpu to fly...Quote:
Originally Posted by bigtoe
I can get the 3500 EB, but i need to act fast. Thanks for your support.. I hope to contribute to what you are doing in here real soon !
:toast:
So this is the place where all the :banana::banana::banana::banana: happens!?
Nice 2 be a member of this great community ;)
--------
Can one of u guys please gimme a short overview about the Pros/Cons the
DFI posseses according to your experiences?
Maybe its time to sum a few things up cause this thread is overwhelming my brain a little and even my time ;)
3500eb is fine get it now. You can always resell if you don't like it.Quote:
Originally Posted by SunTzu69
Will the fact that I have to use a divider with PC-3500 EB kill me ? I see you guyz run 1:1 as much as possible... I thought it wasn't an issue with the A64 but it seems that it is to some extent. I plan to need top performance for gaming especially...
If you guyz say go for the 3500 EB now !! I will...
Quote:
Originally Posted by SunTzu69
I have that same processor and I can't get that thing past 2650 on water. If you are using phase, maybe you'll see 2.85 stable. but I wouldn't coun't on running past 2600 with good water. My EB 3700 can do 268mhz with 3.1v at 3-3-3-10 1T. The timings kinda suck though. I'd rather run 250mhz 1:1 with BH-5 at 2-2-2-6 1T
Can u guys say somethin about the overclockability of various A64 Steppings?
r there any Steppings which r highly-recommended
In my optinion the oc-potential of the a64 differs 2 much to say something general about it what do u think?
i still have a alot of bh5 sticks flying around here so do u think 2x512MB r able to achieve 250MHz @ 1T ?
It comes down to voltage with bh5. with this board and the beta bios, you can do up to 4.0vdimm, but you need a psu with an adjustable pot so you can raise the 3.3v line. or a modded 3.3 line on a psu.Quote:
Originally Posted by KingZer0
from what I've seen, this board was made for BH5
@trans am
thx a lot man :) glad 2 hear that
for me its more important how much i can achieve with out-of-box settings which means a vdimm not above 3,3Volt.
since the 1GB OCZ 3700 EB have been discontinued, what´s the best memory I can get for this board to replace the ocz one ?
Buy some now, its good stuff, to bad its EOL.Quote:
Originally Posted by Loque
no longer available here... so, whats the best I can get now ? Crucial Ballistix ?Quote:
Originally Posted by The Mofo
Try to catch them via Ebay or @ local stores otherwise i would recommend
Crucial Ballistix
i have the same prob. here....
if i put 429/31fsb (i don´t know what apenned to 430), it appears "detecting array"... :mad: ... and i can´t go to windows!!
help :(
Since some of the memory is becoming hard to find what is some really good RAM that will provide some really nice high Bandwidth/Performance scores? I am not looking for Dual Channel kits...just 512 Sticks. That aren't too too high on the price. Sorry this is off topic.
Guys we have a 3500part coming soon (I hope) that is VERY similar to 3500EB and does clock quite well to 500 or so, it also does cas2 where EB was tuned for cas2.5...this may be worth waiting for and as soon as I can i will test and post results.
Crucial seemed to have sent some real good clocking sticks to anand. The :banana::banana::banana::banana: i bought doesnt clock worth a damn.
I would recommend the new OCZ PC3200 REV 2 stuff, seems to clock real high with tight timings.
this place has it (PC3700 EB ). i don't know whether their price is good or bad. by the way, they are in Canada, but ship to the US.Quote:
Originally Posted by SunTzu69
http://www.bytewizecomputers.com/products/7/10/363/6303
Quote:
Originally Posted by serlv
Also, it appears to be available, fairly widely, in the UK. So... if you have friends there. :)
Alright I will wait for that then. Thanks bigtoe you are a big help as always man :p: . I know it is my memory that is holding back my overclocks and I want more!!! :DQuote:
Originally Posted by bigtoe
Also, this place is listing it, too. In stock. I believe they are in the US.
http://www.computerhq.com/OCZ_512MB_...id-430473.html
To bad its only a 512mb kit
And this place...
http://www.microstorm.com/memory/par...id-862097.html
Quote:
Originally Posted by The Mofo
Well, yeah... So, ya get two ( those are 512 sticks ). Was just curious if I could find any. Had to go deep into google pages. There are a few places.
I'm using Mushkin BH-5 for now, myself. But will be checking out my new 3500 EB afterwards. I'm not gonna get 3700, too. :cool:
Here is a nice HTT for me so far. Not a high overclock.
And I decided to take it out of the case :D
I didn't want to ruin my DFI box so I used my old MSI K8T Neo box lol
Edit! 400x5.0 I don't see why some people can't even hit 300 on HTT.
This place has single and dual channel EB listed in stock. It is in Canada - not sure if they ship intl.
http://www.shoprbc.com/ca/shop/?cid=162&p=4
I think I am going to wait for the new OCZ to come out that bigtoe is talking about. I want to see what it can do and around about how much it is going to cost.
Some of the GEIL is doing pretty nice but what I would really like to get my hands on is some Mushkin Level II Black. That was some really nice RAM there. But I have also been seeing the Cosair doing nicely as well. But we all will see in time who is going to come out on top. :p:
Bit of info on Codered's A64Tweaker vs DFI in bios tweaks :)
Seems A64Tweaker even at same settings as DFI bios, is slightly faster and more stressing on system then DFI bios.
i.e. DFI Bios is more stable than A64Tweaker set settings but slightly slower
9x 260HTT at 1.5v vcore
2x 256MB KHX3200K2/512 BH-5 @ 260mhz at 3.28v vdimm with timings of:
2-2-2-6-8-12-2-2-2-2 with
Read Write Q Bypass 16x
Bypass Max 7x
Max Async Latenecy 6ns
Hexus Pifast
A64Tweaker = 51.41s
DFI Bios set = 51.47s
Sandra SP2b Buffered
A64Tweaker = 4037/4038 MB/s
DFI Bios set = 4032/4034 MB/s
Sandra SP2b Unbuffered
A64Tweaker = BSOD unstable
DFI Bios set = 2435/2468 MB/s
DFI bios set allows me to be prime95 and stresscpu stable while A64Tweaker set settings are faster but unstable - apps generate errors too i.e. loading cpuz, a64tweaker, etc
FYI, @260mhz 2-2-2-6-8-12-2-2-2-2 memtest86+ v1.26 reports bandwidth = 1945 MB/s
Interesting.Quote:
Originally Posted by eva2000
The same settings with A64 Tweaker and the BIOS should generate EXACTLY the same results. It would then appear that some of the other settings are being adjusted by the BIOS to improve stability.
There are quite a few settings that I did not provide in A64 tweaker since they did not improve performance, maybe I should re-enable them to allow people to tweak for stability too. I deliberately left out Drive Strength, DQS Strobe tweaks, 32-Byte Granularity, DRAM scrubber controls and a few others.
EDIT: Eva can you post a WPCREDIT screenie of Bus 0, Device 24, Function 2 as set by the BIOS.
yeah re-enable them all :)
wpcredit i haven't used in ages so not sure how to do it heh.. i'll figure it out later :)
Anyone try high vdimm yet, say over 3.5v via 3.3 modded and beta BIOS?
5x400 :slobber:Quote:
Originally Posted by ugp
How many sticks of RAM? 1?
Which bios?
Settings?
CodeRed, I think you should provide a rough guide to include with A64Tweaker. Tell people which settings improve performance, and which are for stability, etc, just general stuff?
Thanks
Some quick results no screenies yet still benching but
i'm at 10x 260HTT with 1:1 ram @260mhz 2-2-2-6 at 3.28v on this board now :)
1T 8-12-2-2-2-2 7x, 16x
Sandra 2004 Pro SP2b
Buffered = 4033/4036 MB/s
Unbuffered = 2428/2484 MB/s
SuperPi
1M = 33s
2M = 1min 17s
4M = 2min 51s
8M = 6min 30s
Everest Home
Read = 4037 MB/s
Write = 1721 MB/s
Hexus Pifast = 47.11s
Memtest86+ v1.26 = 1953 MB/s bandwidth
Yeah I know ...Quote:
Originally Posted by HKPolice
I really need more types of memory to test on. My BH5 runs with the most aggressive timings so thats all I know. I havent a clue what the best settings are for each and every brand/type of memory ... people have to test.
Is anyone using OCZ EL Gold PC3700 rev3 with the DFI board? What FSB have u managed to acheive, and what timings/voltage??
Cheers
yeah i have 2x 512MB OCZ PC3700 Gold rev3 here will get around to testing them.. but may take quite a while hehQuote:
Originally Posted by ColdFusion
Eva, what freq is your cpu running at?
There is something that doesn't match when I compare your results and mine.
I also have Sandra SP2
My timmings are far from yours -> 2.5-4-3-3 1T 2CMD
2x512 ADATA PC4000 running at 500DDR
I got about 37xx Mb in the buffered test but If I do the unbuffered test I get about 30xx Mb! :confused:
The option to do the unbuffered test is the "Enable Buffering/block Prefetch benchmarks" one? What's wrong? I'm sure that mine should be lower than yours at the unbuffered test
My CPU is also far of your superPI time. Mine takes between 1:26 and 1:29 on 2M
:(
you're running unbuffered incorrectly you need to uncheck 9 boxes shown here
http://www.fileshosts.com/AMD/DFI/60...mem-unbuff.jpg
loose mem timings = slower superpi times
http://www.fileshosts.com/AMD/DFI/60...superpi-2m.jpg
http://www.fileshosts.com/AMD/DFI/60...superpi-8m.jpg
http://www.fileshosts.com/AMD/DFI/60...uperpi-32m.jpg
so u guys "r" searching for samsung TCCD chips?
XMS-PC3200 XL rev 1.1 (2-2-2-5)
Samsung 4ns TCCD
DDR PC3200 Platinium Edition rev2 (2-2-2-6)
Samsung 4ns TCCD
A-data Samsung TCCD PC4800 DDR600 ram
new A-Data DDR 600 :D
u could also go for the 3500 and 3700 EB on oc-wear.de i think the ship every where ( in european room)
hope my dfi come this week :D to hit the shi/t out of my hardware :P
if u want good bh-5/6 and cheat search ebay for it because so many people didnt get it that they ve got bh-5 they bought their memory far ago... :D so its good for us !
seEn andL
PS: yeah do it codered its a must to stabilizise ur tweaker with more options ( very very great tool ! really! )
Thanks for replying so quickly to my OCZ EB RAM questions...
I'm wondering why you all aim to hit a 1:1 ratio on your FSB/RAM with the A64? Some have suggested that this does not matter for the A64 because it is always using a divider with the on-board memory controller.
Is there really a performance advantage to running 1:1 on an A64 ? Or is it solely an achievement one strives for in the benchmarking world ?
Thanks !
AMD64 performance all depends on how high your mem speed goes at tight timings, using high HTT with dividers on mem = lower performance unless with dividers mem is at higher speed than what mem would of been at 1:1
well that's what i have read
The bios released some days ago says:
Fixes - Temp reading wrong(on some)
Are your temp readings fixed?
When posting, people could say if their mobo now reads the temps OK or not.
Just a way to see if there is too many ppl like me or not cause mine is not fixed
u ll get better performance on 1:1 than on others on the same mhz!
so ull be faster with 240x10 1:1 than 300x8 with divider its strange but it gains u little bit i tried it....
:confused: ...eva2000!That almost word for word is the exact results that I see first hand. "Memory" is still the very most important consideration and always has been. There is plenty of slight of hand to make impressive HTT numbers appear but when you run a real calculation or application like SuperPi that is an application and not some bench> if you don't see a 'decrease' in the time to run SuperPi then somebody is kidding somebody.Quote:
how high your mem speed goes at tight timings, using high HTT with dividers on mem = lower performance unless with dividers mem is at higher speed than what mem would of been at 1:1
My particular memory will run 240 straight up 1:1 and superPi is 36secs. In fact right out of the box. Been playing the slight of hand divider game and finally have an HTT of 335 and a so-called memory frequency of 260 both as shown in Cpu-Z but superPi has not come back down to 36seconds yet. Hehehehehe. Smoke and mirrors and still the "memory" and as fast and as tight as you can get it is the answer to big benches except where AGP performance is taken into account. This board and likely most boards that seem to slide AGP transfers to the HTT bus can really smoke.
As always if you have super memory = super benches that have been used normally on previous platforms. My guess is that as far as real applications go the A64 will run way ahead of the NF2 style platforms but to see that something besides 3dmark and memtest will have to be run and then the real horsepower of the A64 will show itself for those things that do data transfers using the HTT communications channels. Memory and it faster is still the biggest and baddest key to running fast. Has not changed a bit.
Sincerely, RGone... :cool:
My volt reading has gone totaly mad!
Tried to reflash bios but does not work.
What to do ?
*edit* Changed psu and still same weird volts *
measure with a digital multimeter ;)Quote:
Originally Posted by Ubermann
smartguardion /ihdoctor app underreports voltages and isn't accurate so ignore
Same reason why i brought a new powersupply. :rolleyes:Quote:
Originally Posted by Ubermann
Ok but cpu temp that use to be 39c is now ~53 ?Quote:
Originally Posted by eva2000
It was 1 Stick and I always run it in DIMM3Quote:
Originally Posted by Zeus
RAM Divider was set at 1/2 I didn't mess with it anymore after that last night though. CPU was alittle hotter, ran about 37 Idle but at 275x8.0 right now it is at 30 Idle which I like very much.
It was just a plan and simple clock at 400x5.0 which the Vcore at 1.8 and the Chipset was only at 1.8 as well.
temp measurement in software is buggy = ignore :)
i get same idle temps in that app at 12x 200 = 2400mhz stock and at 11x 245mhz = 2695mhz at 1.75v !
Is your CPU really at 54? Mine reports mine acuurately. Mine idles at 30C and depending on if the Air is on it idles at 25-27 on air. Which isn't bad at all I think.
Is there any news on the 939 DFI LanParty board? I haven't been following this thread and I can't read all 39 pages as I am on dialup still! Stupid internet!
Quick question because I want to shoot for more out of my HTT...is there any real risks of burning the CPU out settings the HTT higher than 400. I want to try 450x5.0 But I am not sure on the dangers.
no way it's at 54C, according to infra-red thermometer my waterblock is only at 26-28C and same cpu on AN50R was 25-30C idle and 36-39C loadQuote:
Originally Posted by ugp
The temps was okej yesterday.Quote:
Originally Posted by eva2000
The volts was a little below.
But today everthing is :banana::banana::banana::banana:ed!
Quote:
Originally Posted by masterofpuppets
nope....nothing.....
In this thread on OCUK forums DFI rekon it'll skip the NF3 939 and we'll have to wait till xmas for the NF4 939. Bet it'll be pushed back even more than that. Hope it aint true.
http://forums.overclockers.co.uk/sho...eadid=17291585
So one stick has got to be the key to ridiculous high HTT. :idea:Quote:
Originally Posted by ugp
Your chip probably didn't run hot because of the high HTT but because of the 1.8Vcore.
What is RAM divider 1/2, is it 150? (thought that was 3/4)
Do you run the modified bios 9/12 and what RAM do you use?
With 1/2 at 400HTT the RAM is at 200. Unless you mean something else.Quote:
Originally Posted by Zeus
Yes I have the 4.0-Volt Mod BIOS and I am only using Infineon PC3200. I have clocked it at 247.5 so far. But the RAM is holding my clocks back.
I was playin' a bit today, and hit 300 HTT with 2x512s, but I noticed the bandwidth sucks. Seems for BH-5, it's best to run 1/1 for bandwidth, but you can get better CPU clocks with 5/6. I'm still not familiar with the LDT multi, not sure how it fits in. :confused: Also, @ 1/1, I can get 255 MHz., but not totally stable at all, and raising vdimm doesn't seem to help. :confused: I've used 3.4v so far, might try higher if I can figure out what's holding me back. One more thing, on my Mobile 3000+, the 8 & 8 1/2 multi show up as 9, so my only options are from 7 1/2 down or 9. :(
Yeah just found out there is a 1/2 option as well.
I really don't know why i can't get high HTT to work. :confused:
Tried one stick in slot 3, still it maxes out at 270. :(
Did you have 1T disabled by chance, so that you ran 2T?
Do you have Apic enabled or disabled in bios?
All I had set on the memory timings was at 2.5-3-3-10. Everything else was on AUTO. I haven't messed with much of the RAM settings. I am about to try for 425x5.0 hehe Wish me luck
I was unable to hit 425 or 450x4.0 but I will mess with it alittle bit and as soon as I get some new memory I will get some higher clocks but until then.
How 'bout Apic, do you have it enabled or disabled?
I'm leaning towards the idea that the SPD chip on my mem is overruling bios settings so that divders won't work.
The SPD forces it to run PC3200 speeds.
That might be the reason for not going higher than a mere 270MHz. :mad:
Even with one stick of RAM, 1/2 divider, multiplier 6x and 1.7V chipset i cannot run high HTT.
What's holding me back?
Thought Clawhammer could run very high HTT?
Is there some magic limit at 320FSB and running 1T ?
Can't get thru it without system hangs.
Any idea's ?
do u mean 320MHz FSB(DRAM-Frequency) or HTT?
because, i don't think, that u would get with your PC3200-RAM 320MHz even with 5V VDIMM :rolleyes: ;)
I passed 320 with 2.9 Volt.
But kinda hard to get system stable above 305 =(
Need help :confused:
Will the ocz booster make more stable volt even if i dont use it to get higher volts ?
Running Aspire psu.
The ClawHammers will hit high HTTs. Just try this... load it at 400HTT with a 5.0 multiplier a 1/2 Divider to start with relaxed timings on the RAM. And then boot and see if it loads. If it does then start tweaking the other settings until you find something that really works. All I did was go straight for 400x5.0 and it worked lol. I need to work on trying to figure out how to get 425 though. Anyone want to loan me a stick of OCZ EB? hehe
I need to get a newer version of SiSoft. So I can compare to other processors. I am currently downloading the newest and I will post some new pics when I get the chance. I got tomorrow off so I cna stay up all night and play. YAY! :D
@ Ubermann you should be able to hit some really high scores with that memory. I don't see what is going on with your system. Please post what settings you are running (Timings, Dividers, Multipliers, Voltage, etc...) Anything that you have changed. And another problem you have is that you have an Aspire PSU. I had one that came with my X-SuperAlien case and it blew up and shorted out on me and never put out the right voltage and hurt my overclocking.
Im running high timmings 3-4-4-10 so its not that good i think compared to low timings.
There will be NO s939 nF3 250 board,the first s939 board that will come out from DFI is one with nF4 and that will be at around Xmas.Quote:
Originally Posted by masterofpuppets
Thats what a have read on a forum from a guy how send an email to DFI,en the answer was that it will be out on xmas.
W0000T!!
Did what UGP did, went into genie bios, selected mem speed 100 (1/2 divider)
Selected multi 5x and 400HTT.... it bloody booted!!
Tested with SuperPi 1m, stable!! :banana:
Right, let's have some more i thought, 410HTT, same thing, 420HTT, same thing, 430HTT, instable, giving "detecting array" message.
So 425, unstable unfortunately...back to 420 and running Prime 95 for a laugh.
As i type this @420x5 it's priming away for over 20 minutes now! :D
Finally it seems to do what i wanted it to do, thanks UGP. ;)
ooooh me going to try this too :)
I had to try also =)
Bandwidth sucked..
(Its with 2T)
I doenst work for newcastles :'(
lol, guys, nothing then 1:1 makes any sense on a A64-rig....your HTT could be 1000MHz.....when u would have a 1/5-divider your sandra-benchies would be @ normal 200MHz-results :rolleyes:
HTT (async-driving), doesn't bring ANY boost....so, just forget that und drive 1:1 and enjoy ;)
Who said it must make sense ?
It was just fun =)
i tried some divider tests at 200HTT just to figure out what each divider sets memory at but in windows cpuz 1.24, 1.23 show mem speed blank and sandra and memtest86+ report mem as 1:1 ???
using 14/09/04 4v modded bios
any ideas ?