Call me crazy 26+ fans 1 case

Been building pcs for a few years now ANY TIPS comments IDEAS Constructive criticisms are appreciated.

User Name: DAVE1210

CPU: i7 960
Motherboard: x58 E760 by EVGA
CPU Overclock Speed: Stock
Video Card & Quantity: 1 x 7800gtx -> ?
Videocard Overclock: ?

Watercooling:YES
CPU Block: XT Swiftech
NorthBridge Block: EK-FB-EVGA-X58-classified acetal-nickel
SouthBridgeBlock: see above
Mosfet Block: see above
Videocard WB/WBs: ?
Radiator & Quantity: 4x XSPC RX360 3x120
Radiator Fans & Quantity: S-Flex E x ~26
Radiator Location:FRONT and REAR
Radiator Fan Direction: IN & UP
Reservoir: 2 x T-VIRUS
Tubing & Size: Primochill White 1/2" ID / 3/4" OD
Barb/Fitting Size: 13mm/19mm
Pump & Quantity: {FUTURE} 3 x DDC 3.25 18W
Pumps-Series/Parallel: SERIES & 2 LOOP

The only case I could find to hold this much crap...
EXTENDED ASCENSION 2'x2'x18" by MountainMods

Way too much tubing 1/2" ID 3/4"OD Primochill but more than enough

some Feser ONE clear (decided on colored rather ...white tubing instead of dye)

no major gpu yet waiting possibly for eterity

two loops decided cpu on one gpus on the other

I figured i'd divy up the rads as 1 for the cpu/chipset and 3 for the gpus seeing where these GTX 480s are

going (that isn't that bad...right?)

the ascent RAM coolers are really good NO RAM WATER

power is a silverstone zeus 1200w to be unisleeved over time as it is modular and I have a spare

I am going to be using compression fittings any advice?

I'm also going to incorporate as few quick disconects as I can they may be needed for pending upgrades near

future

I'll be getting one vid card at a time so quick disconnects MAY save some hassle.


well that is the grand master plan

to start though I'll just be cooling the cpu with 1 rad 1 res(probably not the T) 1 future pump (yes I need a

pump) of course a block maybe a trio of fans to cool it if the thing doesn't leak then ... oh then I might

install the water cooling system into the case power the pump for another 24 then power up the pc providing

no signs of leaks.


I am sorta new to liquid so ..
CorsairH50 was my first

am I in over my head ???

Again ANY TIPS comments IDEAS Constructive criticisms are appreciated.

a basic water cooler would probably cost you less than 26 scythe fans
and MM case is big enough to install the compressor and radiator inside it!
just a ghetto chiller, no 0 celsius overkill, but it's way more compact and quiet than 4 rads with 24 fans

My MM case have 29 Fans, all at 800RPM. :D

crazy

Quote:

---

Originally Posted by kone

My MM case have 29 Fans, all at 800RPM. :D

---

I have a nice industrial grade rheo to control 50 watts these use less I think and the RPMs will be nice a low

I bought the fans all at a price less then 10 bucks a piece bulk so saved a lot there usually these are in the 15-20 range

pedastal is a nice option I chose to actually make my case exhaust out the top which works great in terms of positive pressure, and I will be filtering slightly to keep pet hair out.

oh

DID I MENTION I am a liquid cooling newbie

any flaws in either my master plan or my current plan of action.

I know where the links are just looking for a little more tips.

yes I am nuts when it comes to building big

Just a useful bit of acoustic information. If you take a sound of lets say 10 case fans you double the decibel level. Its a fact for anything.

already tested these fans out in the case and the db levels are good no extraneous sounds and no vibrations

Nice idea! Personally, I like your choice of fans! Luckily you have more than enough case to handle all that equipment. Be sure to keep us up on how things go with the build.

Discounts or no that's a ton of money spent with no 980x! Maybe go 920 until the cheaper 32nm later this year? 970?

http://i787.photobucket.com/albums/y...OWPOKE/mx3.png

This is mb/cpu/gpu all on 1 loop. 1 pa120.3 and 3 s-flex F's. 480's are really hot but I don't believe they are 3x 360 rad worth, are you getting 3 of them? (if so maybe 3 rads).

Like you I built an ascension and felt the need to jam it to the brim and fill every slot. I have 22 s-flex's, before that 22 noctuas. I had 3 loops at one time. I don't believe you need a comprehensive exhaust strategy when watercooling. 2 120's out the back is more than enough for me. From my build I've learned that if you decide to watercool everything in your case the need for moving a lot of air inside isn't pressing. If you're doing some hybrid where you wc the cpu and air cool the gpu that's completely different, but in a roomy ascension rads on all intake fans and just 1 or 2 exhaust fans out the back is fine.

Some ascension specific advice, take the front panel off and install everything to just that panel and then attach to frame. Even with its huge size working inside the case gets very tricky. Doing it that way allows you to route your million front fan cables between your drive bays, easy way to toally hide all those cables.

My ascension has the following:
22 s-flex F
2x pa120.3, 1x pa120.4
2 xspc single pump bay res with mcp350/mcp355
5970+ek block, 5870 + ek block
gigabyte ud7 + ek block
980x + ek supreme hf block
9 ssds, 1 platter drive
6 bay devices besides the res's: lcd,dvd burner,2 fan controllers,x-fi front panel,multicard reader/usb hub

power is enermax galaxy 1250

After having it run for a couple months I see now I could do with 12 fans and would have gotten only half the bells and whistles and put it all in a mm ufo instead.

Filling an ascension is more work then you think, but it's a good problem to have as problems go.

Good luck. :)

Quote:

---

Originally Posted by =[PULSAR]=

Just a useful bit of acoustic information. If you take a sound of lets say 10 case fans you double the decibel level. Its a fact for anything.

---

Umm? What?

Quote:

---

Originally Posted by nikhsub1

Umm? What?

---

If you take a fan that is 30db and you run 10 of those fans the sound level would be 60db roughly. It was an acoustics test I did roughly 10 years ago.

my math says it would be roughly 40db. you have to double the number of fans for each 3db increase. however, every 10x in acoustic power it will "sound" twice as loud.

I have had a lot of fans in one case before. only have 31 in the Drunken Monkey right now, but if I went back to a push/pull setup, it would be a crap load of fans.. running 500-800RPM fans keep noise down, my power supply has been modded, so it is silent now, but the damn DDC 3.25's are LOUD. I have 2.5" accoustic foam above them, and some sound deadening pads all around them, but still very loud. If it was not for the damn pumps, you can hardly tell when the PC is on, or off.
There are a few 980x's out there for dirt cheap, if you look around the various forums, a lot of people are calling their new 980x's DOA, but the problem is, their BIOS is not new enough to run the 6 cores, and the RMA them.. Risky, but I am happy with mine. :yepp:

Quote:

---

Originally Posted by defect9

my math says it would be roughly 40db. you have to double the number of fans for each 3db increase. however, every 10x in acoustic power it will "sound" twice as loud.

---

That is pretty much my understanding as well. To be clear;
IF:
1x = 30dBa
2x = 33dBa
4x = 36dBa
8x = 39dBa
so on and so on.

more fans have been used ;)
http://www.tgdaily.com/games-and-ent...s-%E2%80%9Cday

You asked for it... you're crazy!

Well, it's a lot. It's certainly not the most, but it's more than commonly used.

My only real comment is:

CPU: i7 960
Motherboard: x58 E760 by EVGA
CPU Overclock Speed: Stock
Video Card & Quantity: 1 x 7800gtx -> ?
Videocard Overclock: ?

Radiator & Quantity: 4x XSPC RX360 3x120
Radiator Fans & Quantity: S-Flex E x ~26

Really?

4 triple rads with push/pull 6 fans each (I'm assuming), for a STOCK speed 960 and a single lower-grade GPU?

Way, Way, Way overkill.

So much so that you aren't even beginning to use that much radiator space.

An awful lot of wasted potential (and cash) there. Of course, you'll be pretty much future-proof for quite a while.

Quote:

---

Originally Posted by Soulwind

Well, it's a lot. It's certainly not the most, but it's more than commonly used.

My only real comment is:

CPU: i7 960
Motherboard: x58 E760 by EVGA
CPU Overclock Speed: Stock
Video Card & Quantity: 1 x 7800gtx -> ?
Videocard Overclock: ?

Radiator & Quantity: 4x XSPC RX360 3x120
Radiator Fans & Quantity: S-Flex E x ~26

Really?

4 triple rads with push/pull 6 fans each (I'm assuming), for a STOCK speed 960 and a single lower-grade GPU?

Way, Way, Way overkill.

So much so that you aren't even beginning to use that much radiator space.

An awful lot of wasted potential (and cash) there. Of course, you'll be pretty much future-proof for quite a while.

---

maybe he is going to solder on the 960 proc to the GPU?

Quote:

---

Originally Posted by DarthBeavis

maybe he is going to solder on the 960 proc to the GPU?

---

Heh, now that would be interesting to see. :D:D:D


It's his money, of course, and he's more than welcome to piss it away however he wants.

I just kind of cringe when I see folks wanting to spend major cash like this.

~550 on a 3.2 ghz 960 as opposed to ~260 on a 2.66 ghz 920 that could be easily oc'd to 4+ ghz with that cooling system. A massively overpowered setup for the rig he's proposing. etc

I don't like to "bad mouth" or criticize anyone for making odd choices (lord knows I've done/tried a LOT of wierd and/or stupid ideas with my machines), but it does seem that a lot of folks trying to get into WC spend more time figuring out how big they can go on the setup and not enough time on the rest of the rig.

Quote:

---

Originally Posted by nikhsub1

That is pretty much my understanding as well. To be clear;
IF:
1x = 30dBa
2x = 33dBa
4x = 36dBa
8x = 39dBa
so on and so on.

---

Yes, every 3dB gain in acoustic output generally requires a doubling of power. So if one were to go from the typical 5 -7 fans in a case to 20-something fans, that would likely be an increase of at least 6dB or even 9dB or more of fan noise at the same RPM, etc.

Quote:

---

Originally Posted by Soulwind

Heh, now that would be interesting to see. :D:D:D


It's his money, of course, and he's more than welcome to piss it away however he wants.

I just kind of cringe when I see folks wanting to spend major cash like this.

~550 on a 3.2 ghz 960 as opposed to ~260 on a 2.66 ghz 920 that could be easily oc'd to 4+ ghz with that cooling system. A massively overpowered setup for the rig he's proposing. etc

I don't like to "bad mouth" or criticize anyone for making odd choices (lord knows I've done/tried a LOT of wierd and/or stupid ideas with my machines), but it does seem that a lot of folks trying to get into WC spend more time figuring out how big they can go on the setup and not enough time on the rest of the rig.

---

Could not agree more. a single 240mm rad would be more than enough for what the OP is looking for (stock speeds and quiet).

Quote:

---

Originally Posted by kone

My MM case have 29 Fans, all at 800RPM. :D

---

Only 27 here :( :up:

First, welcome to xtremesystems! Second, you should do a project log as this will be awesome. You will love the MM case, I personally prefer going horizontal on the MB as it is easier work on IMHO. I have done a triple loop before, GPU's in one, NB/SB and mosfets in another and the CPU on it's own. The MCP355 pump will be enough for each loop and if you are going this big I would do three independent loops, if you can why not, right? Anyway, I would direct the air flow over the rads into the case. That case is big enough to have exhaust ports to let it equalize. Quick disconnects are nice, been using them for about a year and every time I take them out I end up putting them back in. I would consider doing a pump/res combo to make it easier to set up, but I like the T-virus, looks very cool. If you haven't already gotten the 960, I would skip it and either get a 920 or go for the gold and get the 980x, either way you will not be disappointed. I have had the 975, the 960 and the 920 and the 920 will perform as good if not better than the other two unless you are doing extreme cooling. As far as doing a chiller, sure you could, but then you have to either be able to control the water temp or insulate, done that one two and it was fun, but I went back to just water. I would do a phase unit before I would do a water chiller, more compact and and better temps. Like it has already been mentioned, having the front off while installing your gear makes things easier. If you plan on doing SLI with two or three GTX480's, then rethink the PSU, maybe something slightly larger. Better to do it now and not need it then not have it and need it. Install a fitting with three ports towards the bottom of each loop so you can install a drain. I use a QD there so I can just plug in and drain, easy, peasy. The last thing to remember is to have fun with it. Don't be afraid to change things once you get it setup, this is a hobby and should be fun.