Here's A Special WR (P4 650).........

for all you doubters of Cryo-tek who said it wasn't possible to hold a high load @ low temps on an autocascade http://img255.imageshack.us/img255/3536/5680zd.gif. If you're wondering what I'm talking about, check here - http://www.xtremesystems.org/forums/...ad.php?t=97265
BTW - I have absolutely NO IDEA what I'm doing on this Asus P5wd2E-Premium so please excuse the poor results of the benches.....at least until I figure out what all the settings on this mobo do.....;)

The CPU:

http://img152.imageshack.us/img152/1...ated6500lt.jpg

Initial Boot:

http://img209.imageshack.us/img209/529/1213cy.jpg

The Screenie - I hope it counts since I hadn't yet updated my CPUZ so my validation file isn't allowed :(

http://img92.imageshack.us/img92/9742/cpu60595rg.jpg

This is what matters though...an 8m @ a HIGHER SPEED than the previous WR. Vcore was actually drooping on the shot (I didn't bother adjusting my droop mod :p:). Running Vcore was around 1.70v. ~-100C Evap temps LOADED....not bad for a single compressor and a heater on the back of the mobo, eh? That makes this unit 2 for 2 -> 2 CPU's, 2 WR's :cool: Now to figure out how to get 1.9Vcore...:D

http://img146.imageshack.us/img146/7236/340x178m4yj.jpg

Special thx to FCG for loaning me this setup to test my unit (and of course to Cryo-tek for modding it) :toast:

Nice!

VERY nice! I`m also loving the "smiley" right at the start of the post!! :D:D

Kenny

Nice work Steven :toast:

What settings? This is cake compared to a DFI setup your so used to. Btw, your supposed to show us a pic with the temp probe shown while the 8M is running ;) :D

Sorry I couldn't resist, we'd all love to have a cooling unit like that. Congrats to Cryo on a real feat, and a nice number on that 650 :toast:

Quote:

---

Originally Posted by G H Z

What settings? This is cake compared to a DFI setup your so used to. Btw, your supposed to show us a pic with the temp probe shown while the 8M is running ;) :D

Sorry I couldn't resist, we'd all love to have a cooling unit like that. Congrats to Cryo on a real feat, and a nice number on that 650 :toast:

---

Hehehe...if only you've ever seen the bios of one of these Asus boards ;) I haven't heard of over 1/2 of these settings. My probe is sitting atop my autocascade and I can't get a pic of it in the same shot as the monitor...just gotta take my word for it ;) Probe on the die of the cpu shows a deltaT of 7C from idle to load. Try that with your DI container and you'll see just how hard that is to achieve :p:

Thanks for the suppory guys...I'm gonna try 1.8V+ on another board this week :D

Interesting to see you trying something new, figured you would have to with that autocascade. Nice work :toast: .

nice clock and nice unit :toast:

Nice.. not sure what to think Kev on 930 and now you on 650 lol

I am not surprised at all, I will try to get WR for 930;)
bring it on for 1.9v vcore,
Nice insulation work bro;)

Can't wait to see higher vcore results. Nice job !

nice result indeed!

can u take the insulation off after youre done with the mobo?

Yes you can put the sealstring of but it's an hard job :p:

Nice result

Quote:

---

Originally Posted by Onepagebook

I am not surprised at all, I will try to get WR for 930;)
bring it on for 1.9v vcore,
Nice insulation work bro;)

---

oh man you're going torture that poor 930 hehe

pics of your autocascade ? :slobber:

Quote:

---

Originally Posted by Supertim0r

pics of your autocascade ? :slobber:

---

I'll get a few when I'm done with the mods, but I've got a couple with the work in progress:

Evap(s) ;)

http://img155.imageshack.us/img155/3...adparts5ey.jpg

Torn to bits :D

http://www.xtremesystems.org/forums/...1&d=1146526984

Heads Done :cool:

http://www.xtremesystems.org/forums/...1&d=1146941060

oooh narrower evap base to mount on LGA775 boards ?

Quote:

---

Originally Posted by eva2000

oooh narrower evap base to mount on LGA775 boards ?

---

Hmmm...dunno about that...but it seems to fit fine

http://img153.imageshack.us/img153/4272/7752xc.jpg

im being thick but one evap head cools the cpu wat does the other one do? gpu ? chipset? pretty tastey setup mate. im gonna build my first dual cascade in the summer( havent built a single stage before but my cousin works repairing industrial fridges so hes gonna help me get started).congrats on the work !!!

nice.. what's the diameter measure of the evap copper based ?

well his cascaDe is so powerful i'd imagine he could cool 2x cpus for 2 systems at the same time LOL

Quote:

---

Originally Posted by eva2000

nice.. what's the diameter measure of the evap copper based ?

---

They're [modified] chilly1 evaps ;) -> 1.5"

Quote:

---

Originally Posted by s7e9h3n

Heads Done :cool:

---

Thats pretty trick but it needs one more ;)

Ha, ha, ha.....s7e9h3n gets into "dark side" day by day - more and more.... :D :toast: :p:

this cooler is huge !
nice stuff...Intel...:D
conroe soon ?

Quote:

---

Originally Posted by hipro5

Ha, ha, ha.....s7e9h3n gets into "dark side" day by day - more and more.... :D :toast: :p:

---

Yes...the force is strong with him :p:

Grats s7e9h3n....that should quell the storm of doubters. Next they'll be asking you to run a Smithfield XE :rolleyes:

Anyway, sick speed there for sure!