Search:

Type: Posts; User: kolombo; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    7,791

    Try serial gpu rig. The flow in any gpu bloks...

    Try serial gpu rig. The flow in any gpu bloks will be higher then in parallel .
  2. After cleaning the loop pomp can`t move water !...

    After cleaning the loop pomp can`t move water ! Try to drain air, if any into the pomp. Can`t see any other problem but this.
  3. Replies
    11
    Views
    1,554

    Pomp>RES , not good idea . The air will dampf...

    Pomp>RES , not good idea . The air will dampf quite enough pomp pressure, i think. Thus entire flow capacity will be awkward.
  4. Replies
    13
    Views
    2,331

    Timing pomp - the old new face of WC teror.:rofl:

    Timing pomp - the old new face of WC teror.:rofl:
  5. Replies
    13
    Views
    2,331

    Yea.. , same old story,and another negative...

    Yea.. , same old story,and another negative comment
  6. Replies
    9
    Views
    955

    Two loops, fine , but one loop with 2 pomps in...

    Two loops, fine , but one loop with 2 pomps in serial is more safety without comprpmise cooling ability.
  7. Replies
    24
    Views
    4,291

    Adding some xtra hardware to achieve no failure...

    Adding some xtra hardware to achieve no failure improvement , is like building tower of cards in open window room.
    Remember Murphy`s law ..New systems generate new problems...., funny isn`t it?
  8. Replies
    21
    Views
    4,738

    Let see some results .This idea is too old and...

    Let see some results .This idea is too old and abandoned.
  9. Replies
    3
    Views
    833

    always serial

    always serial
  10. Replies
    33
    Views
    2,798

    how bad is the reality

    did anybody really put this dilemma on the operating table ?-and completely be overjoyed of single loop.
  11. Replies
    33
    Views
    2,798

    parallel - not good idea!

    If you want to optimize flow the best option is to place the pumps in parallel, as long as you size the pumps appropriately to the system this the best way to get maximum flow for the lowest cost.
    ...
  12. Replies
    5
    Views
    974

    two pomps in series

    IMO better way, than two separate loops . More secure scenario in case any pomp failure , and about 30% more flow rate in the loop.
  13. Replies
    116
    Views
    16,918

    litle locksmith`s job

    Shoud use some shim, cos procesore core was too small and fragile
  14. Replies
    116
    Views
    16,918

    almost forgotten

    :up:
    s.A SOLTEK -75DRV2 , ATLON THUNDERBIRD 1.0 -1.5GHz
  15. Replies
    116
    Views
    16,918

    not first ,but second

    http://img713.imageshack.us/img713/1019/dmc0028t.th.jpg
  16. Replies
    13
    Views
    1,188

    dust clean up

    On my rig have no pro with cleaning the dust from the rad , in case of pulling fan config. In other case - push rad fans, this mission could be very unpleasant and dusty.
  17. Replies
    43
    Views
    2,425

    Marry Christmas and best wishes from BULGARIA.

    Marry Christmas and best wishes from BULGARIA.
  18. Replies
    10
    Views
    1,185

    Loop/Rad/Pump Config. Issue

    Did You tiltover the case aside for a while , presumably to evacuate air through outlet barb of the rad when pomp`s on. You should add some more liquid into the rig, guess.
  19. Replies
    5,777
    Views
    5,494,802

    my basket

    Always money short for my watercooling plans

    http://img231.imageshack.us/img231/2179/p8230028.th.jpg
    http://img18.imageshack.us/img18/1016/p8010033small.th.jpg...
  20. Replies
    30
    Views
    1,565

    air gap maybe

    No way to squeeze water after pomp outlet so mutch. No way allso to lose water into the rig. Probably air gap has been collected into the rad ? Must check.
  21. Thread: WC setup?

    by kolombo
    Replies
    1
    Views
    367

    Wc Loop

    Take a look some pics at WC case gallery , and will find any anlightenment.
  22. Replies
    27
    Views
    1,252

    HAPPY BIRTHDAY, AND BEST WISHES FROM ALL...

    HAPPY BIRTHDAY, AND BEST WISHES FROM ALL BULGARIAN FENS :bday:
  23. bong cooler

    you have no idea how wrong is this way you chase (bong cooler).At first glance of a quite simple task to nave be done, you will start to play djumandjy.good luck.
  24. Have anybody played or thought about impeler...

    Have anybody played or thought about impeler diameter and rpm . Without increasing the velocity genereted from the impeler , looks to me mission unpossible . At first place and the easyest way to me...
  25. what`s the diference?

    same surface aria , less restrictive is the real advantage of X-flow - if the barbs are the same as each ather , and beter flow rig. :shrug:
Results 1 to 25 of 30
Page 1 of 2 1 2