Bolt-on RAM/VRM sinks for 4850/4870?

[Creig]

Well, it has been over a month past the time that iandh said his 4850/4870 sinks should be available and there's nary a sign of them in the usual shops (Sidewinder, Petras, etc). Is any other source planning on making bolt-on ram/vrm sinks for the 4850 or 4870? D-Tek Uni-Sink, perhaps?

[Sparky]

I just ordered a 4870 recently, it is on its way. I'm waiting for iandh's sinks at this point

[Boyu]

made it my self:

just need a little polishing n anodized it maybe.

[Petra]

You mean these?

[Sparky]

You mean these?

http://www.petrastech.com/other/4870iandhTease.jpg

I ordered a set 5 minutes ago
Was I the first to order? Was I was I?

[Petra]

Was I the first to order? Was I was I?

Yes, yes you were...

[roofsniper]

nice those look good i might order some. hope they perform well.

[bigslappy]

You mean these?

them prutty !!! ... Got some for 4870X2 MaYbE ???

[babalouj]

Those don't look nearly big enough for the vrms but i'm not gonna count them out until I see results.

[evilrad]

You mean these?

FINALLY!!!! Just ordered a set. My new build will finally be complete.

[evil-98]

OMG WOW lol when b/c i need them now!

EDIT

NVM ordering now!

[twwen2]

Hmm nice. Me likey the red .

I must say though,

Full-cover.....FTW!

[Omastar]

$40? Srsly.

[iandh]

nice those look good i might order some. hope they perform well.

Those don't look nearly big enough for the vrms but i'm not gonna count them out until I see results.

I've been testing them for several weeks on two different 4870's. So far the highest VRM temp I've measured is 90C, which is not abnormal. I've seen temps in the 80-90 range on 8800GT's even.

edit: FYI one card is using an Accelero S1 with a Yate SL running full speed (haha sleeve bearing already starting to go out , and the other card was running with an MCW60 and two front mounted stock Lian Li fans running undervolted at 1100RPM). Bottom line is that in both cases the card had good airflow.

That said, good case airflow is a must with this card, regardless of what cooling you use on it. The sinks could be gigantic and the VRM's would still overheat in a case with poor airflow. Even high surface area forged copper sinks like the swiftech/enzo's are no more effective than a square block of copper when you are not moving air through the pins. They actually will radiate into each other, reducing the effective surface area. That is why the fins are so widely spaced on my sinks... too high of a fin density and you can actually lose effective surface area.

$40? Srsly.

That's what the last few models have sold for as well. It's just the cost of having them made entirely in the USA, entirely in California for that matter, and the cost of business here is higher than other states. The benefit though is that I am able to be directly involved in production. The shop I have these made at actually is making these under their normal hourly rate... also, although they sell fairly well they aren't exactly what I would call a high volume item.

[Utnorris]

Do you make them for the 4850? And do they come in blue, FTW?

Utnorris

[iandh]

Do you make them for the 4850? And do they come in blue, FTW?

Utnorris

Not yet... that one is still up in the air as we have had less demand for the 4850's. I have to move a certain amount of them or my shop doesn't even break even on the tooling cost.

Red is the only color we are doing at the moment, trying to keep the finishing cost down for the moment since we are not sure how these will sell yet.

[noobzed]

too little vrm hs, no ?

[Omastar]

That's what the last few models have sold for as well. It's just the cost of having them made entirely in the USA, entirely in California for that matter, and the cost of business here is higher than other states. The benefit though is that I am able to be directly involved in production. The shop I have these made at actually is making these under their normal hourly rate... also, although they sell fairly well they aren't exactly what I would call a high volume item.

I know...I frequently debated whether or not investing $40 in a pretty much one time use RAMsink solution was worth it, or if just reusing the same EnzoTech sinks made more sense. I also figured it was a low volume item, but at $45 for an MCW60 and $40 for these, I could nearly buy an FC block...but that'd be an even worse fiscal decision. I admire the craftsmanship on these, for sure, but I'd like to see your sinks become a higher volume item, carried on more etailers and such.

[Sparky]

I know...I frequently debated whether or not investing $40 in a pretty much one time use RAMsink solution was worth it, or if just reusing the same EnzoTech sinks made more sense. I also figured it was a low volume item, but at $45 for an MCW60 and $40 for these, I could nearly buy an FC block...but that'd be an even worse fiscal decision. I admire the craftsmanship on these, for sure, but I'd like to see your sinks become a higher volume item, carried on more etailers and such.

For me, I already had the MCW60 from a while ago when I first built my loop, so it worked out fine.

[leo_bsb]

yeah, the idea behind this is to reuse the old GPU only block so you will keep the costs down for each video card upgrade.
I already bought the full cover from koolance, it is working really well BTW.
The cost for a new watercooling user will be the same, since I bought the koolance block for $92 but you will save in the long run. The advantage on the full cover is a nicer and easier tubing routing and it is easy to set it for SLI or crossfire.

[Pansuu]

too little vrm hs, no ?

Yep, way too small vrm sink

DIY and just enought:

[dymONE]

too little vrm hs, no ?

YES !! toooo little

[Sparky]

I'll give a rundown how well they work when they arrive. If they end up being too small (which I doubt since iandh has used them no trouble so far) then I'll have to return them or something and get something else. But I'm not too worried since he's used them up to this point with no issues.

[Yozzman]

I'll give a rundown how well they work when they arrive. If they end up being too small (which I doubt since iandh has used them no trouble so far) then I'll have to return them or something and get something else. But I'm not too worried since he's used them up to this point with no issues.

+1 Looking forward to see temps!

[iandh]

too little vrm hs, no ?

Yep, way too small vrm sink

DIY and just enought:

YES !! toooo little

I don't mean for this comment to sound rude, but did any of you read the thread up until this point?

They are only too small if you have poor case airflow.

I'll give a rundown how well they work when they arrive. If they end up being too small (which I doubt since iandh has used them no trouble so far) then I'll have to return them or something and get something else. But I'm not too worried since he's used them up to this point with no issues.

If there is any trouble with the VRM sinks once these get out, I'll make a larger version and supply them for free to anyone that bought the sinks. I am already afraid that there will be problems because (1) People are pushing this already hot running card with benches like furmark that IMO they are not designed to handle, and (2) Everyone's definition of "good" airflow is different (3) For some reason some people seem to be getting absurdly hot running cards, while mine and other's are just "normal" hot. This could come back to the case airflow thing, or it could be due to bad VRM's... there was a thread about that a short while back.

I personally haven't had a single problem yet... I am typing on a system that is running one of the cards (the air cooled one) right at this moment. The watercooled system was sitting in much less airflow and I would run Crysis for hours on end on that system.

It isn't like I just randomly guessed, oh, I'll make these things stupidly tiny so that I fry everyone's cards. I made a prototype first, and it worked fine so I designed these from it. I don't want to fry my card, and I run these on it so take that as you may... keep in mind that I designed these and they were in production before all the VRM hotness hype/scare hit the internet. If I had designed them yesterday I would have made them gigantic just so I didn't have to hear it from anyone.