Looking Detail Baby Monster "ASUS MAXIMUS V GENE"

[Dumo]

Summarized OC' guide

http://kingpincooling.com/forum/show...1&postcount=29

[OC Nub]

This is my first micro board. This thing seems to be pretty awesome, having fun testing memory for now.

[l0ud_sil3nc3]

This is my first micro board. This thing seems to be pretty awesome, having fun testing memory for now.

you have one too?

I am out of the loop

it is an awesome board, especially with the right cpu/memory.

[Dumo]

Awesome run there OC

Info about LB...



Latency Boundary:

Simply put you can set the biggest value of 14 first to find the limitation of your DRAM/CPU after which you can try setting 6 or 9 (which are good compromises between stability and performance) if you think your setup is able to run it.
LB is tied to secondary and tertiary timings
Setting 1 if your ram can keep up..



Got this with samsung 30nm ram..



BBSE..

[OC Nub]

Thanks Dumo!

The board clocks extremely well. Can boot at 2800mhz+ but my memory has reached its limits, so 2600-2666 is about tops for now.

G.Skill RipjawsZ 2133 16gb kit @2600

[OC Nub]

you have one too?

I am out of the loop

it is an awesome board, especially with the right cpu/memory.

Another few days and retail hits, cant wait! For once I made it to the loop

[Hazzan]

you have one too?

I am out of the loop

it is an awesome board, especially with the right cpu/memory.

+ 1 when you run under cold on chip..............

[l0ud_sil3nc3]

+ 1 when you run under cold on chip..............

I wouldn't know I am playing with a x54 2500k on air

[bwanaaa]

whats the diff between ripjaws z and ripjaws x?

[OC Nub]

^ Im not really sure, these are a quad ch. kit, I thought the X were dual ch.?

G.Skill 8gb 2800c11.

[AVulgarPicture]

these are some serious clocks. looking amazing.

[l0ud_sil3nc3]

whats the diff between ripjaws z and ripjaws x?

heat spreader

^ Im not really sure, these are a quad ch. kit, I thought the X were dual ch.?

G.Skill 8gb 2800c11.

niiiiiceeee OCNub, I take it that is half of the 2133 9-11-10 Hynix kit of Ripjaw Z's?

[l0ud_sil3nc3]

not sure why 6-9-6/7-9-7 do not work, but bclk oc is very nice.

[Dumo]

+ 1 when you run under cold on chip..............

Its gonna be awesome runs om Zan

air...

[stasio]

not sure why 6-9-6/7-9-7 do not work, but bclk oc is very nice.

For my BBSE tRP must be higher (to pass PI32).
Anybody tested BBSE with XMP?
I getting 8-9-13-24.

[l0ud_sil3nc3]

For my BBSE tRP must be higher (to pass PI32).
Anybody tested BBSE with XMP?
I getting 8-9-13-24.

nice to know however I was able to pass 32M with the above settings.

I will try the XMP, I usually never use them so not sure what it sets on Z77.

[Hazzan]

Its gonna be awesome runs om Zan

air...

cool Om Roy....

using E0 or E1 ? my chip E0 very bad IMC

[Leeghoofd]

whats the diff between ripjaws z and ripjaws x?

RipjawsX for SB (mainly PSC /BBSE based )
RipjawsZ for SB-E, quad channel kits usually Hynix and Samsung

[AVulgarPicture]

i cant believe the ETA on these boards is 30th april here in Aust.
reading these results is literally painful.

[aussie-revhead]

Yeah it sux, but they look great, I cant wait to get my hands on one. I might even grab two, one for my water gamer/benching rig and one for dedicated single stage testing/benching.

Good times ahead.

[Eldonko]

0805 still the latest BIOS for this right?

EDIT - Nevermind, looks like 0880 is the latest now.

[kagula323]

Its gonna be awesome runs om Zan

air...

Dumo wich kit exactly do you have? can u post a newegg link to it ? btw: great frequency on that ram

[Dumo]

Dumo wich kit exactly do you have? can u post a newegg link to it ? btw: great frequency on that ram

Thanks kagula
Mem. used Gskill TridentX 2800

[AVulgarPicture]

Is the Asus t- topology built into these boards? Or is it for later gen z77?

I'm keen on a formula too depending on its price vs the sniper3

[OC Nub]

There is so much tweaking that can be done on this board, I can just keep playing around with memory without getting bored.

I put the Samsung 30nm kit back in to try 2600 again. After doing a little reading at KP Forums about the board, I was able to get them benchable at 2600 10-12-12 with Latency Boundary 6, by adjusting the Transmitter, and Receiver Slew. Need to play around with the 2 settings a little, but this seemed to work with this kit. With my GSkill's, the best I can do is LB 8, so the 32m time was a bit slower.