Last edited by Leeghoofd; 02-14-2012 at 03:47 PM.
Question : Why do some overclockers switch into d*ckmode when money is involved
Remark : They call me Pro Asus Saaya yupp, I agree
I had figured since the exploding board issues, this would be an exception. As Leeghoofd said, they should all come with f8 bios now.
Thanks, look forward to seeing you results.
I finally switched to Asus, now you are posting in the Giga threads lol. Have you tested any of the Asus x79 boards?
Will test the UD7 this week, UD3 inbound too... maybe new rev of UD5 too... Asus boards seem more mature, less bugs and far superior bios...
Question : Why do some overclockers switch into d*ckmode when money is involved
Remark : They call me Pro Asus Saaya yupp, I agree
Have you gotten around to testing the UD3? I'm not impressed at all, the board refuses to boot with any strap config whatsoever. I've tried two 3930K's, one C1 and one C2, both stop at 4.8Ghz with any reasonable voltage. Memory OC past XMP is a no go. Been trying for over a month now, looking to get a RIVE...
Intel i7 3930K C2 @ 4700 mhz (100 x 47) 1.4v
EK Supremacy/EK XTC 420+280/EK DCP4.0/PrimoChill 1/2 ID 3/4 OD
Asus Rampage IV EXTREME
16 GB G.Skill RipjawsZ @ 2400 CL10-12-11-1T
Zotac GTX670
Antec Quattro 850W
Intel 330 180 GB + Micron C400 128 GB
LD Cooling PC-V7 B/R
Hi people,
I have gotten my UD5 and 3820 while the forum was down. I could easily get to 4.3 GHz via multiplier overclocking but I must be missing something when using the 125 MHz Bclk strap, the system just won't post.
What else exactly is involved/needed to be set with Strap 1.25? I set Vtt to 1.14V, CPU VCore to 1.34 for 36x125, and set the turbo mode multipliers to 36x for all cores.
xp I am still mentally on my X58 I guess.
On a side note, my UD5 came with BIOS F8 out of the box. Yay...
Maybe anybody could point me out to some BIOS templates with settings?
Last edited by Amurtigress; 02-23-2012 at 08:14 AM.
i7-3820 C2 @ 4500 MHz, Batch 3201B130
Corsair H100
GA-X79-UD5, BIOS F10
4x4 GB G.Skill Ripjaws F3-17000CL11Q-16GBXL @ 2100MHz
ASUS ENGTX560Ti 1 GB @ 960 MHz
Coolermaster Silent Pro Gold 700W
60 GB OCZ Vortex 2 SSD
2 TB WD Caviar Black
1 TB Samsung Spinpoint F1 HD103UJ (FW upgraded)
1 TB Samsung Spinpoint F3 HD103SJ
ASUS Xonar D2X
Question : Why do some overclockers switch into d*ckmode when money is involved
Remark : They call me Pro Asus Saaya yupp, I agree
Intel i7 3930K C2 @ 4700 mhz (100 x 47) 1.4v
EK Supremacy/EK XTC 420+280/EK DCP4.0/PrimoChill 1/2 ID 3/4 OD
Asus Rampage IV EXTREME
16 GB G.Skill RipjawsZ @ 2400 CL10-12-11-1T
Zotac GTX670
Antec Quattro 850W
Intel 330 180 GB + Micron C400 128 GB
LD Cooling PC-V7 B/R
Hi there,
just to mention it, as I posted in another thread, I got the 1.25 strap working by reducing BCLK to 90 MHz. Overclocks are going up to 4.7 Ghz now...however that causes a number of other problems.
1) In RAID mode there is a 50-50 chance of my OCZ Vertex 2 60 GB SSD to not be detected.
2) onboard LAN shows a drastic decrease in network performance. Upstream bitrate is limited to 200 kbits/sec, in LAN and internet. Goes away immediately when returning to BCLK 100/Strap 1.00
Prolly unrelated to the 90 Mhz BCLK: A memory stick that holds my Windows 7 install disk worked well on my old X58A-UD7 does not boot at all. Despite trying all emulation modes (HD, Floppy, forced floppy, CDROM and auto)
BIOS F9 at least solves the Razer mouse problems in the BIOS Setup and the bootup stalls in AHCI mode.
Last edited by Amurtigress; 02-25-2012 at 05:52 PM.
i7-3820 C2 @ 4500 MHz, Batch 3201B130
Corsair H100
GA-X79-UD5, BIOS F10
4x4 GB G.Skill Ripjaws F3-17000CL11Q-16GBXL @ 2100MHz
ASUS ENGTX560Ti 1 GB @ 960 MHz
Coolermaster Silent Pro Gold 700W
60 GB OCZ Vortex 2 SSD
2 TB WD Caviar Black
1 TB Samsung Spinpoint F1 HD103UJ (FW upgraded)
1 TB Samsung Spinpoint F3 HD103SJ
ASUS Xonar D2X
Bookmarks