Micron GTS on dice

[Nanok]

Hade some dice left from bench, and decided to abuse my OCZ 1600 7.6.6
They are my best kit out if 5 or 6 iv hade, bench stabel at + 800 6.5.5.16 2.1V

Pot with some g.skill 8000HZ



5.4.4.15@2.45V




6.5.5.15@2.45V


Superpi 1m was stabel around the same speed as everest

[Mafio]

good work mate...1000+ cas6 is awesome

which mobo did you use???

[Kabauterman]

Everest says Rampage Extreme

[Nosfer@tu]

Great Job Nanok

Like always you deliver power

[Sam__]

Great work!!

[teurorist]

nice rampage
good work

[Shahryar_NEO]

great work mate .

[iddqd]

now try the same thing without dice

[tech]

oh no???....
good result..!!!

[audigy]

excellent, Cas 6 1000mhz

[Nanok]

now try the same thing without dice

Without extreme cooling is not posibel sure.

[saaya]

very nice
did your mem degrade at all after that session?

[Mean Machine]

Nice frequencies... Might I just ask, how do you insulate your pot? I have one of your pots, wrapping them in paper doesn't seem to be enough. (Mobo is of course insulated around the mem sockets)

[WaterFlex]

Very well done

[Gautam]

Badass, awesome work.

[Nanok]

very nice
did your mem degrade at all after that session?

The ram did not degrade at all, i did not want to "push" to hard becourse it was my best, and only kit.
The mainboard was Insulated with eraser, around the dimms.
The rampot was Insulated with Armorflex tape, i can make pic. later and post if you want.
By the way, i wold like soo see your result with rampot Mean Mashine !

[zanzabar]

what kind of timings dose a good gts kit normally do with 800mhz on an x48 on air

[Hyperhorn]

Nice RAM-OC from you again. I like that you prefer tight timings and no lazy MHz hunting. Congrats, awesome results!
Maybe I should finally use your RAM-pot (same model, bought 2nd hand), I`m just watching it for months. Atm my limit for my 2 x 1 GiB D9GTR are 2.03 V for reasons of safety^^, but that`s good enough for >800 MHz 6-5-5-13 @ SPi 32M (or 6-5-5-14 @2.00) at least. 5-4-4 should give an very nice extra boost for my lowclock competition.

[Mean Machine]

The ram did not degrade at all, i did not want to "push" to hard becourse it was my best, and only kit.
The mainboard was Insulated with eraser, around the dimms.
The rampot was Insulated with Armorflex tape, i can make pic. later and post if you want.
By the way, i wold like soo see your result with rampot Mean Mashine !

I'm more than happy to oblige. Crucial Ballistix PC16000 9-9-9-24 these are, 2.48V. Just a pretty quick test. D9GTS as well.

http://valid.canardpc.com/show_oc.php?id=584940

That was at about -75c. The weird thing is that the mems run absolutely fine even at -130c, I never went below that. There's probably some more to gain, I think the NB was the limiting factor.

[iddqd]

Without extreme cooling is not posibel sure.

should be. capacitors are the limiting factor, right? so as long as you can cool them down enough to prevent failure, you should (theoretically) get the same results.

[Nanok]

Cooling on ram works, or else everybody would run at those speeds.

[M.Beier]

Impressive work John, however, I cant help wondering whats wrong with the 1060mhz, the BW seems very low, might be PL or strap
5.3ghz and 1060mhz ram 6-5-5- I would have expected above 16GB/s

[Nanok]

pl9 strap 400

[dejanbinladen]

omg this is brutal latency on that freq

[iddqd]

Cooling on ram works, or else everybody would run at those speeds.

I'm still curious what this ram can do without dice