DFI NF4 None Expert Series Bios Timing For TCCD series, FF,LA,LE,LC,LD ete.

[GSKILL TECH]

the following timing is for DFi Ultra-d, SLi-D, SLi-DR
Can NOT use for Expert, Venus

F1-3200DSU2-1GBFX
2.6-2.8V; HTT=5; FSB=200
Dram Frequency Set: 200 (1:1)
Command Per Clock: Enable (1t) (2T if not stable using 1T)
Cas: 2
Trcd: 2
Tras: 5
Trp: 2
Trc: 7
Trfc: 13~18
Trrd: 2
Ter: 2
Twtr: 1~2
Trwt: 2~3
Tref: 3684
Twcl: 1
Dram Bank Interleave: Enable

Dqs Skew Control: Auto
Dqs Skew Value: 0
Dram Drive Strength: 7 (or Best Value For Your System)
Darm Date Drive Strength: 3 (or Best Value For Your System)
Max Async Latency: 6~7ns
Darm Response: Normal
Read Preamble Time: 4~5ns
Idlecycle Limit: 256
Dynamic Counter: Enable
R/w Queue Bypass:16
Bypass Max: 7
32 Byte Granularity: Disable

F1-3200DSU2-1GBLA
DDR400
2.6-2.8V; HTT=5; FSB=200
Dram Frequency Set: 200 (1:1)
Command Per Clock: Enable (1t) (2T if not stable using 1T)
Cas: 2
Trcd: 2
Tras: 5
Trp: 2
Trc: 7
Trfc: 13~18
Trrd: 2
Ter: 2
Twtr: 1~2
Trwt: 2~3
Tref: 3684
Twcl: 1
Dram Bank Interleave: Enable

Dqs Skew Control: Auto
Dqs Skew Value: 0
Dram Drive Strength: 7 (or Best Value For Your System)
Darm Date Drive Strength: 3 (or Best Value For Your System)
Max Async Latency: 6~7ns
Darm Response: Normal
Read Preamble Time: 4~5ns
Idlecycle Limit: 256
Dynamic Counter: Enable
R/w Queue Bypass:16
Bypass Max: 7
32 Byte Granularity: Disable

DDR600
2.6-2.8V; HTT=3; FSB=300
Dram Frequency Set: 200 (1:1)
Command Per Clock: Enable (1t) (2T if not stable using 1T)
Cas: 2.5
Trcd: 4
Tras: 8
Trp: 4
Trc: 7
Trfc: 13~18
Trrd: 2
Ter: 2
Twtr: 1~2
Trwt: 2~3
Tref: 3684
Twcl: 1
Dram Bank Interleave: Enable

Dqs Skew Control: Auto
Dqs Skew Value: 0
Dram Drive Strength: 7 (or Best Value For Your System)
Darm Date Drive Strength: 3 (or Best Value For Your System)
Max Async Latency: 8~9ns
Darm Response: Normal
Read Preamble Time: 5~6ns
Idlecycle Limit: 256
Dynamic Counter: Enable
R/w Queue Bypass:16
Bypass Max: 7
32 Byte Granularity: Disable

F1-3200DSU2-1GBLE
DDR400
2.6-2.8V; HTT=5; FSB=200
Dram Frequency Set: 200 (1:1)
Command Per Clock: Enable (1t) (2T if not stable using 1T)
Cas: 2
Trcd: 2
Tras: 5
Trp: 2
Trc: 7
Trfc: 13~18
Trrd: 2
Ter: 2
Twtr: 1~2
Trwt: 2~3
Tref: 3684
Twcl: 1
Dram Bank Interleave: Enable

Dqs Skew Control: Auto
Dqs Skew Value: 0
Dram Drive Strength: 7 (or Best Value For Your System)
Darm Date Drive Strength: 3 (or Best Value For Your System)
Max Async Latency: 6~7ns
Darm Response: Normal
Read Preamble Time: 4~5ns
Idlecycle Limit: 256
Dynamic Counter: Enable
R/w Queue Bypass:16
Bypass Max: 7
32 Byte Granularity: Disable

DDR550
2.6-2.8V; HTT=3; FSB=275
Dram Frequency Set: 200 (1:1)
Command Per Clock: Enable (1t) (2T if not stable using 1T)
Cas: 2.5
Trcd: 3
Tras: 5
Trp: 3
Trc: 7
Trfc: 13~18
Trrd: 2
Ter: 2
Twtr: 1~2
Trwt: 2~3
Tref: 3684
Twcl: 1
Dram Bank Interleave: Enable

Dqs Skew Control: Auto
Dqs Skew Value: 0
Dram Drive Strength: 7 (or Best Value For Your System)
Darm Date Drive Strength: 3 (or Best Value For Your System)
Max Async Latency: 7~9ns
Darm Response: Normal
Read Preamble Time: 5~6ns
Idlecycle Limit: 256
Dynamic Counter: Enable
R/w Queue Bypass:16
Bypass Max: 7
32 Byte Granularity: Disable

F1-4800DSU2-1GBFF
DDR400
2.6-2.8V; HTT=5; FSB=200
Dram Frequency Set: 200 (1:1)
Command Per Clock: Enable (1t) (2T if not stable using 1T)
Cas: 2
Trcd: 2
Tras: 5
Trp: 2
Trc: 7
Trfc: 13~18
Trrd: 2
Ter: 2
Twtr: 1~2
Trwt: 2~3
Tref: 3684
Twcl: 1
Dram Bank Interleave: Enable

Dqs Skew Control: Auto
Dqs Skew Value: 0
Dram Drive Strength: 7 (or Best Value For Your System)
Darm Date Drive Strength: 3 (or Best Value For Your System)
Max Async Latency: 6~7ns
Darm Response: Normal
Read Preamble Time: 4~5ns
Idlecycle Limit: 256
Dynamic Counter: Enable
R/w Queue Bypass:16
Bypass Max: 7
32 Byte Granularity: Disable

DDR550
2.6-2.8V; HTT=3; FSB=275
Dram Frequency Set: 200 (1:1)
Command Per Clock: Enable (1t) (2T if not stable using 1T)
Cas: 2.5
Trcd: 3
Tras: 5
Trp: 3
Trc: 7
Trfc: 13~18
Trrd: 2
Ter: 2
Twtr: 1~2
Trwt: 2~3
Tref: 3684
Twcl: 1
Dram Bank Interleave: Enable

Dqs Skew Control: Auto
Dqs Skew Value: 0
Dram Drive Strength: 7 (or Best Value For Your System)
Darm Date Drive Strength: 3 (or Best Value For Your System)
Max Async Latency: 7~9ns
Darm Response: Normal
Read Preamble Time: 4~6ns
Idlecycle Limit: 256
Dynamic Counter: Enable
R/w Queue Bypass:16
Bypass Max: 7
32 Byte Granularity: Disable

DDR600
2.6-2.8V; HTT=3; FSB=300
Dram Frequency Set: 200 (1:1)
Command Per Clock: Enable (1t) (2T if not stable using 1T)
Cas: 2.5
Trcd: 4
Tras: 8
Trp: 4
Trc: 7
Trfc: 13~18
Trrd: 2
Ter: 2
Twtr: 1~2
Trwt: 2~3
Tref: 3684
Twcl: 1
Dram Bank Interleave: Enable

Dqs Skew Control: Auto
Dqs Skew Value: 0
Dram Drive Strength: 7 (or Best Value For Your System)
Darm Date Drive Strength: 3 (or Best Value For Your System)
Max Async Latency: 8~9ns
Darm Response: Normal
Read Preamble Time: 5~6ns
Idlecycle Limit: 256
Dynamic Counter: Enable
R/w Queue Bypass:16
Bypass Max: 7
32 Byte Granularity: Disable

[kakaroto]

Very usefull, thanks G.STechnician!

[adidassler]

Hi There G.S Tech, Have followed those settings and timings with my DFI Expert and 1GBFX but whenever i ran the Memtest, thousands of errors occuring in test 6 of the memtest. I run 1t and 2t but still have thousands of errors in test six.

Pls help. Thanks!

[GSKILL TECH]

Hi There G.S Tech, Have followed those settings and timings with my DFI Expert and 1GBFX but whenever i ran the Memtest, thousands of errors occuring in test 6 of the memtest. I run 1t and 2t but still have thousands of errors in test six.

Pls help. Thanks!

please check the title.. it is for Ultra-D. Sli-d, Sli-DR
not for expert, venus!!

[adidassler]

Sorry for that G.S.Tech...
Will Really Appreciate if you can post also settings and timings for my Expert. Pls..... Thanks a Lot!

[GSKILL TECH]

i will try but expert, venus is really hard to have a "fix char" for everyone
DDS and DDDS is really different from person to person

[adidassler]

Hi there G.S. Tech

Currently, im having a new mobo DFI RS482 Infinity.

Pls do help me with mem timings for its is far different from my current rig (SIG below) in bios. not familiar with those new terms.

Many Thanks

[over@locker886]

F1-3200DSU2-1GBFX
Settings: DFI Ultra-D/SLI-D
2.6-2.8V usually some like more; HTT=3; FSB=300 or more
Dram Frequency Set: 200 (1:1)
Command Per Clock: Enable (1t) (2T if not stable using 1T)
Cas: 2,5
Trcd: 4
Tras: 7
Trp: 3
Trc: 7
Trfc: 13~14~19
Trrd: 4
Ter: 2
Twtr: 1~2
Trwt: 2~3
Tref: 100Mhz 7,8us/1,95us or 200Mhz 15,6us
Twcl: 1
Dram Bank Interleave: Disable

Dqs Skew Control: Auto
Dqs Skew Value: 0
Dram Drive Strength: auto
Darm Date Drive Strength: auto
Max Async Latency: ~9ns max 10
Darm Response: Normal
Read Preamble Time: ~5,5-6ns
Idlecycle Limit: 256
Dynamic Counter: Disable
R/w Queue Bypass:16
Bypass Max: 7
32 Byte Granularity: Disable
32M max


1M max


I think was the fastest Gskill FX forever..

[Modulok]

well it's about time I have somewhere to look for tested settings for my 1GBFF kit. THANKS GS TECH

Just got a new opteron 148 and I couldnt get stock to run well...had a hunch that it was my ram settings. Running ddr400 2-2-2-5 now and its going well. Hope to start OCing soon.

ps, is there a mailing list that we could get on depending on our register gskill ram? Like I got an email from alice about new ddr2 ram, it would be nice to get emailed these settings...I probably would never have found them if it wasnt for seeing this thread posted in another forum...just a suggestion.

[LordofDoom]

Thank you so much GST!!! For both the RMA and everything! My system is up and running again and stable so far on DDR600/2.7ghz.

[GSKILL TECH]

Thank you so much GST!!! For both the RMA and everything! My system is up and running again and stable so far on DDR600/2.7ghz.

i hope my hand writing is not too hard to read

happy to see the thing solve

[LordHanderson]

I've an X2 3800+ that runs @ 2,8Ghz vCore default with async mem (ddr @ 400) + DFI LanParty UT NF-4 Ultra-D (last official DFI bios) + G.Skill 4800FF (2x512). There're stability problem if I want to use my 4800 @ DDR 550 or @ DDR 600. I don't found the perfect stability with my hw; when i try to set my 4800FF to DDR 550 (275x10) or @ DDR 600 (300x9). I've problem with the boot or instability after the loginf of WinXP Pro (SP2).

I've read your guide but I've the same problem.
Please G.S Technician or someone help me to solve this problem!


Thanks

[LordHanderson]

I've an X2 3800+ that runs @ 2,8Ghz vCore default with async mem (ddr @ 400) + DFI LanParty UT NF-4 Ultra-D (last official DFI bios) + G.Skill 4800FF (2x512). There're stability problem if I want to use my 4800 @ DDR 550 or @ DDR 600. I don't found the perfect stability with my hw; when i try to set my 4800FF to DDR 550 (275x10) or @ DDR 600 (300x9). I've problem with the boot or instability after the loginf of WinXP Pro (SP2).

I've read your guide but I've the same problem.
Please G.S Technician or someone help me to solve this problem!


Thanks

Is there someone?

[GSKILL TECH]

I've an X2 3800+ that runs @ 2,8Ghz vCore default with async mem (ddr @ 400) + DFI LanParty UT NF-4 Ultra-D (last official DFI bios) + G.Skill 4800FF (2x512). There're stability problem if I want to use my 4800 @ DDR 550 or @ DDR 600. I don't found the perfect stability with my hw; when i try to set my 4800FF to DDR 550 (275x10) or @ DDR 600 (300x9). I've problem with the boot or instability after the loginf of WinXP Pro (SP2).

I've read your guide but I've the same problem.
Please G.S Technician or someone help me to solve this problem!


Thanks

which bios you use? try to use old bios if possible

[LordHanderson]

which bios you use? try to use old bios if possible

I'm using the 6.0 PG (date 4/06/2006), the last official DFI.

what version do you suggest?