kayl, What refrigerant was used. I went through the topic but couldn't find any info on it.
They are superb temps and the Case looks great. Any pics of the front of the case mate. I love black cases, look the best IMO.
kayl, What refrigerant was used. I went through the topic but couldn't find any info on it.
They are superb temps and the Case looks great. Any pics of the front of the case mate. I love black cases, look the best IMO.
Last edited by kayl; 12-03-2006 at 04:48 PM.
The cascade is all finished and leaves tomorrow finally, no leaks for weeks now so happy to send. Last night of benching I finally managed to add the vcore mod with the thinner wire and run 1.8v. this wire made the vmod a little easier, a mag lamp would have been handy though.
Seems that my E6600 at 4.1ghz is quiet a lot colder than 920D at 5.1gmz so cascade should handle any vcore and cpu.
Results here, X6800 at 4.9ghz -97c load
http://www.xtremesystems.org/forums/...ht=bob%28nz%29
Last edited by kayl; 02-13-2007 at 07:02 AM.
Last edited by kayl; 02-28-2007 at 06:06 AM.
Wow, that a tight fit in those last two pictures
Originally Posted by Jack
yes, its very very tight, i really hope i can get it all in there hey
It is going to be hot inside the case. Perhaps you should build an aircon unit to cool ityes, its very very tight, i really hope i can get it all in there hey
Last edited by kayl; 03-01-2007 at 07:22 AM.
Looks good buddy!
Best Regards,
Xavier
"I prefer to fly alone... when alone, I perform those little coups of audacity which amuse me..." Col. René Fonck (1894-1953), the Ace of Aces.
thanxs before
Brazed the cascade up over the weekend, vacuumed both stages and charged first stage with r290 for now and second stage with a tad of r290 and the rest ethylene.
Fired it up last night and it ran fine. Nice little ice show, evap head sat at around -90c with 5psi low side for load handling and 200psi on second stages high side.
Static charge was around 150psi. I then shut everything down and let the ice melt. I finished the remaining insulation and attached the load tester and then started the first stage.
Once down to temp I started the second stage, then there was nothing. I reset the mains at my power board and tried again, same result. So I either have a dead second stage compressor or some electrical wires that havn’t been insulated properly damit. Ill Check that tonight and hopefully get some quad core benching. That or destroy the cascade and find another compressor. I really hope it’s the wiring or connection come loose.
well i cant tell you what is what but good luck with finding the problem. Hopefully its just wiring.
My Custom Pressure/Temperature Charts for Various Refrigerants
QX6700 @ 3900 | EVGA 680i |2 GB Corsair 8500 Dominator | 7800 GT SLi | Silverstone 1KW | Seagate 7200.9 Barracuda RAID 0 + Hitachi Deskstar 2TB RAID 0 | SS Phase w/ Cryostar Evap | MIPS Full Motherboard cooling
My Fake Quad Core is better than your real Quad Core! **cough**Barcelona**cough**
Lian Li Cube Case with Phase and Water DONE!!
thanxs TopherTony
i managed to get it going, it might have been the safy on my mains??
Didnt get much time to bench. so far idle around -80c and load with 1.84vcore -75c
best validation was 4583.99MHZ and with 1mB SPi run 11.45sec at 4452MHz.
I need to shorten both stages capillary lines and see if i can get some better temps.
http://valid.x86-secret.com/show_oc?id=174856
Last edited by kayl; 03-08-2007 at 03:16 AM.
Really nice kayl
regards
------------------------------------------------------------------------------------------------------------------------------------------------
My Work: LittleDevil's SS Cases, LittleDevil's SS Worklog, LD CPU-R1 Dice/LN˛ Pots, LD GFX-R1 Dice/LN˛ Pots,
LittleDevil LD PC-V10, LittleDevil's K-Type Temp Display, |EMAIL: ldphasechange@gmail.com
LD PC-V8 Watercooling Cases: LINK
LD PC-V8 ATX/HPTX Watercoolig PC case with 10 expansion slots: LINK NEW!
-------------------------------------------------------------------------------------------------------------
www.ldcooling.com
Find US on Facebook
thanxs LD, not bad effort hey, cascade start to finish over the weekend Just got to clean it up a little and put the case on. Ill look at tuning it over the next few weeks though got some other units i have to work on.Originally Posted by LittleDevil
Last edited by kayl; 03-06-2007 at 08:46 PM.
Some more pics. also manged some higher overclocks wprime and few others.
4607MHz validation on the QX6700 at 1.81v or so.
http://valid.x86-secret.com/show_oc?id=176006
and around 4.3ghz benchable for Wprime.
I hope none of our friends (or anyone) is feeling the wrath of cyclone George or the cyclone coming in behind George.
Are things okay for you kayl?
thanxs Runmc , im ok and same with family & friends, the 2 cyclones were on my side of Australia but further up the coast, we had a massive heat wave around the same time 42c for a few days, but thats the worst it got. Actually yesterdays bench session in the shed was in 35-40c temps ran the casacade for around 4 hours
Last edited by kayl; 03-10-2007 at 06:57 PM.
i put my pentium 4 925D in and managed 5.7 validation
5.46GHZ 32m SPI run
5.46ghz 1mb SPI @21.17328sec
Before i put the cpu in i put the cascade on the heatload tester, seems that vmoded 1.8vcore on QX6700 is alot hotter than 255w.
the 925 is hotter though than the QX6700, i had to drop vcore to 1.76v to get it stable at higher OC. this was still hotter than my quadcore which i find interesting.
http://valid.x86-secret.com/show_oc?id=176062
Last edited by kayl; 03-10-2007 at 09:14 PM.
Very nice Kayl, I`m still impressed by your OC results, cascade too
yes i agree luke
kaly is one of the few that likes to bench as well
thanxs luke, they are some nice numbers arnt they.
Bazx yes there arnt too many big builds that are into overclocking big. I really like your bench setup/workshop though, one of the best i have seen.
What kind evap temps you got with that QX @ 4.4Ghz~ and 925D @ 5.4Ghz under load?
-70c with the QX6700 with wprime and other applications.
-60c lowest seen so far on the 925D, shes really hot hey compared to Qx6700. I havnt run quad prime though and wont bother at these voltages dont want to kill any cpus/motherboards.
only -60-70*c with those CPUs and ethylene ??
http://WWW.PIOTRES.COM
My productions (phase-change and containers) : Click here to see links...
Phase-change units, cascades, chillers and Ln2/DI containers builder - contact : piotres@piotres.com
Bookmarks