XS Yonah T2600ES competition !!!

[4ng3ldust]

I cheated Used a boxed one

[runmc]

Nice runs there Tyrou You don't have a cold boot problem with your mobo when run with phase?

@runmc....Hows the board so far?

Getting better with vcore mod ram is @ 4-4-4-12 @ 2.05v Patriot 5300 I can't tighten it up any at this v setting. I'm still on air with some left in it.

Thanks for the help with hdw. Dumo and Fugger

[NapalmV5]

Getting better with vcore mod ram is @ 4-4-4-12 @ 2.05v Patriot 5300 I can't tighten it up any at this v setting. I'm still on air with some left in it.

Thanks for the help with hdw. Dumo and Fugger

nice!! wats vcore @? dats wat im hoping for with higher v.

btw, like ur sig runmc - Jesus - sweet saviour

[runmc]

nice!! wats vcore @? dats wat im hoping for with higher v.

btw, like ur sig runmc - Jesus - sweet saviour

Vcore was 1.57 in bios for my fastest run. The vcore mod made all the difference. If you have bios set to 1.50v and your trimmer set to 100kohms you will get 1.64v. You don't need to adjust the trimmer at all.
NapalmV5 - you will be happy with a vcore mod - good luck

BTW - I have a IHS on my chip.

[railer]

Getting better with vcore mod ram is @ 4-4-4-12 @ 2.05v Patriot 5300 I can't tighten it up any at this v setting. I'm still on air with some left in it.

Thanks for the help with hdw. Dumo and Fugger

Now this is impressive score and clock on AIR. Damn 18's on air. If anyone would tell me this 2 monts ago it would be science fiction. Now these crazy Yonah's

[Joe Camel]

Vcore was 1.57 in bios for my fastest run. The vcore mod made all the difference. If you have bios set to 1.50v and your trimmer set to 100kohms you will get 1.64v. You don't need to adjust the trimmer at all.
NapalmV5 - you will be happy with a vcore mod - good luck

BTW - I have a IHS on my chip.

about how much better? (OC)
(rough B4 and after #'s?)


(guess it doesn't matter, i couldn't solder a 0 gauge wire on the side of a barn if my life depended on it. .. )

[GoriLLakoS]

GoriLLakoS - 18.547 - Core Duo T2600 ES @ 3.356 MHz - SS - Memory 258.2 but 3:4 4-4-4-7



GoriLLakoS - 18m 36s 844ms - T2600ES Core Duo - 2.16 @ 3315Mhz - SS - 3:4 - 13x255 4-4-4-7

[Sloppy]

runmc and gorilla, those are the yonahs from fcg right?

[GoriLLakoS]

YEap...we got step 4..

Runmc...we got the same pi time..:P:

[M.Beier]

Step 4
2*1GB Ballistix

231*13, 20.031sec, no memset used yet.... - I'll submit picture once I hit 19.xxx sec, btw, I use stock fan

[runmc]

I made some single stage runs tonight @ 1.60v. I had no problems booting, my problem was I couldn't get back into the bios to set my vdimm volt higher. Well I could have but i would have had to shut down for a minute or two and I was too hyped up. Next time I'll set vdimm higher before I turn on phase. I'm almost sure I can run 270fsb maybe more.

Single stage was holding at -45c

The cpu is from FCG, so it's an early release. The board is from pccriminal via Dumo.

[Rol-Co]

I made some single stage runs tonight @ 1.60v. I had no problems booting, my problem was I couldn't get back into the bios to set my vdimm volt higher. Well I could have but i would have had to shut down for a minute or two and I was too hyped up. Next time I'll set vdimm higher before I turn on phase. I'm almost sure I can run 270fsb maybe more.

Single stage was holding at -45c

The cpu is from FCG, so it's an early release. The board is from pccriminal via Dumo.

why is clockgen on 1600 mhz clock? and not on the 3400

.

[G H Z]

After I figured out to remove red jumpers

BIOS 1.03
Mushkin XP6400
Tuniq cooled
No mods



900/900+ XTX action tomorrow

[kiwi]

What red jumpers you are talking about?

[Rol-Co]

After I figured out to remove red jumpers

BIOS 1.03
Mushkin XP6400
Tuniq cooled
No mods



900/900+ XTX action tomorrow

Nice bios 1.03? is it better then the previous one? still got 1.02 here, do i need the update?

[G H Z]

32m



kiwi,

The red jumpers that limit the Aopen board to 166-199fsb only.

[CAL930]

by Kubokubo

32m New WR!!!!

CPU: Intel Core Duo T2600 (2.16G) QKHK ES
M/B: AOpen i975Xa-YDG (Rev.00A) (BIOS： R1.03)
MEMORY : Corsair TWIN2X1024A-5400UL V1.5 512MB x2
VGA: ATi Xpert98XL 8M (PCI)
HDD: HITACHI HDS722580VLAT20 (80GB, 7200rpm, 2MB)
CPU Cooling: KURIPRO4+ DICE
PowerSupply: Zippy 600GE (600W)

OS: Windows Server 2003

KUBOKUBO'S SYSTEM

[Gamer]

damn, will need to vmod this board to get higher clocks I guess.

nice results.

[guess2098]

http://www.iamxtreme.com/cpu/t2600/cpu060420_04.htm

I just did some more compare between 2.16, 2.6, 3, 3.3G benchmark and also some FX60 @ 3G score

SUPER PI 32M
LOWER IS BETTER


CPU MARK
HIGHER IS BETTER


3DMark03
HIGHER IS BETTER


3DMark05
HIGHER IS BETTER


3DMark06
HIGHER IS BETTER


Sandra CPU Arithmetic Benchmark
HIGHER IS BETTER


Sandra CPU Multi-Media Benchmark
HIGHER IS BETTER

[guess2098]

so i think Yonah is like FX60
XD

only pi is faster but other tests shows Yonah @ 3G is only a little bit better than FX60 3G

[jmax_oc]

Very nice

[dogsx2]

Nice charts Denny. With a better mb on Yonah would most likely come better results, Aopen is not an Intel BA mb.

[wwwww]

Nice charts Denny. With a better mb on Yonah would most likely come better results, Aopen is not an Intel BA mb.

The Aopen is fine in performance - 975X chipset - beats those 945GM chipsets...

[fredyama]

By Tarosa

New modPI 1.5 XS 1M WR: 16.297s @3655.1MHz (FSB 281.2MHz x 13)

[SoF]

congratz on this insane 1m to teamjapan - outstanding as always