A64 3200+ ClawHammer

[burn88]

hello to all! here what for hour they are successful to obtain from my CPU



temp CPU: 25°C!

[UTF Nightmare]

You must get more out it with that temp. Maybe more Vcore if it's possible ?
What is the FSB? Cant't see it
What kind of cooler you use?

[burn88]

the computer was on the balcony! and the vCore is to 1,8 V

[UTF Nightmare]

And you can't get more then 2586MHz?
That's not really impressive

[Gautam]

Depending on the date of the proc it could be pretty nice. I hit 33.9 or so at 253x10...highest mine could go on cold air. Of course back when I had that proc, I matched what plenty had on phase...times change and so do the clocks.

You should probably look into getting some better RAM.

[burn88]

I would have to try! as soon as the cold returns

[burn88]

Depending on the date of the proc it could be pretty nice. I hit 33.9 or so at 253x10...highest mine could go on cold air. Of course back when I had that proc, I matched what plenty had on phase...times change and so do the clocks.

You should probably look into getting some better RAM.

between much time I would not have to change ram

[Backbone]

Here is one from me
2540 on 1.6V

and one sucide shot 2700 mhz on 1.7

The stepping of mine is CAA2C(I think everyone know about this stepping)

[Gautam]

I sure do.

[madman2233]

try doing that with a CO revision

[burn88]

I sure do.

freq ram?

[Gautam]

255MHz 3-2-2-1.5.

@madman: I've never owned a C0, but had a very early CG back from when most still had C0's, which is what I was talking about earlier.



Ancient nForce3 150 board (remember those)? Good times...probably could've done 2.6+ in the DFI.

Week on this puppy is 0405, nearly two years old. The C0's sometimes ended up below this on single stage.

[Zeus]

(remember those)

I do.



Ancient C0 revision (one of the very first S754ClawHammers) and an ancient Shuttle AN50R.

[Gautam]

Very nice. Must have been quite a lucky one. Most didn't seem to hit 2.4 on air regardless...remember quite a few maxing out below 2.7 on phase. Nicely volted too, I like that.

[TurkeyFace]

Here is one from me
2540 on 1.6V

and one sucide shot 2700 mhz on 1.7

The stepping of mine is CAA2C(I think everyone know about this stepping)

how did you raise the multi to 13x with that +3000?

[Gautam]

I don't see any one using a 13x multi...

Btw, backbone, I'd say something is up with your score...should be quite a bit faster.

[TurkeyFace]

I don't see any one using a 13x multi...

Btw, backbone, I'd say something is up with your score...should be quite a bit faster.

look at the top picture that I quoted...it doesnt look like 9 to me...if it isn't a 13 then it looks like a 10 on the CPU Z screen shot

[Gautam]

Double click the picture to expand it to full-size, heh. It's 10x253.9 in the first one and 9x300 in the second.

[TurkeyFace]

omg...I'm so stupid...CLAWHAMMER...not winchester...I'm stupid

[Backbone]

I don't see any one using a 13x multi...

Btw, backbone, I'd say something is up with your score...should be quite a bit faster.

I use a memory devider becouse my memory hate Clawhammers's mem.controlers.
This stepping is for FX - but I can't change multi

[learners permit]

My 3400 co would do only 2420 on air.

[burn88]

new result!

[i found nemo]

And you can't get more then 2586MHz?
That's not really impressive

dude, don't be such a jerk, these chips don't o/c like the new venices and fx's i think it's pretty decent o/c but the pi time is off a bit try to tighten your timings a little

[i found nemo]

it was a 10* multi cuz the 512 cache, lower cache, amd raises the multi to compensate

[Zeus]

dude, don't be such a jerk, these chips don't o/c like the new venices and fx's i think it's pretty decent o/c but the pi time is off a bit try to tighten your timings a little

He probably never have had one, the ones who do know how hard 2,5GHz+ was to get with these.

Saying it's not impressive is a bit harsh, unless you've owned one up to 2.6GHz or higher on air or water.

Spi time is bad because of RAM speed/ timings.