G.Skill Welcome everyone posts her/his review in here, old, new, doesn't matter.
G.S.T
G.Skill Welcome everyone posts her/his review in here, old, new, doesn't matter.
G.S.T
Feel free to contact ustech@gskillusa.com or use our G.Skill Q&A Sub-Forum, if having any questions about G.Skill products
Check out our items on NewEgg
Here's my gskill GH Winbond UTT 512mbx2
269mhz @ 1.5-2-2-0 at 3.7vdimm at 1T with SuperPi4 million
http://img466.imageshack.us/img466/9...7vdimmsupe.jpg
Allendale E6300@2380mhz @1.28vcore(Vostok water cooling kit)
Asrock 775Twins-HDTV (ATi Xpress 300)
OCZ value 512mb x 2 @ 340mhz @ 4-4-3-5
IDE Hitachi 80gb 7200rpm 2 mb
Inno3D 7900GT
AOpen Combo 52x 32x RW 16x DVD
Panasonic Floppy
OCZ Power Stream 520 watt
icute casing with front blue CCFC, 2 80mm rear casing fan and 1 80mm casing fan on top.
G.Skill 2x512MB PC4400FC
Warning for extreme use only!
Several days ago I received a set of G.skill PC4400FC’s. The new, bright yellow design on the heatspreaders reminded me that this is a new generation of G.Skill. G.Skill is known for their extreme, high end TCCD, so I couldn’t wait to try these out.
The PC4400FC’s are rated for 2.5-4-4-8 (PC4400) @ 2.7-2.9v. According to G.Skill, all the new sets are going to be solely TCCD based, and just to make sure I took a little peak and sure enough they are Samsung TCCD 0516. There had been rumors that TCCD was being phased out and replaced with TCC5, but this seems to dispel these rumors.
The test setup is an AMD socket 939 Opteron 146 on a DFI LP NF4 Ulra-D (what else would I use?). Also since this Opteron is a 10 multiplier chip, I ran everthing with the 10x multiplier at a 1:1 ratio.
The PC4400FC’s are rated for 2.5-4-4-8, but who wants to run memory at its rated speed? I immediately put them at 2.5-3-3-6 with 2.7v. Now for some reason this set didn’t like 2.7v so I put them at 2.8v and they ran just fine.
To get the ram to 285, I had to loosen the TRCD to 4. Even with 2.9v, TRCD-3 wouldn’t work. This is typical of TCCD sets though, TRCD-4 works much better than 3 and doesn’t negatively impact performance too much. So the timings were 2.5-4-3-6 and I maintained voltage at 2.8v, which seems to be the sweet spot on this set.
Now up to 295 with the exact same settings
Same settings again at 305
The ram really likes 2.5-4-3-6 with 2.8 volts, here is 310.
With 2.5-4-3-6 and 2.8 volts, the set maxed out at 312.
This is a great set of ram. First of all, it managed to do DDR624 with 2.5-4-3-6 with 2.8 volts, which is comparable to any above-average set of TCCD. Also, keep in mind that the ram would probably go further. The set is rated for 2.5-4-4-8, and it did 312 with tighter timings than this! The best part is that it’s fairly inexpensive for high end TCCD, $170 at newegg. If you’re going to overclock with a high FSB/HTT, this is a great set of ram.
http://www.newegg.com/Product/Produc...82E16820231019
Last edited by BB mods's; 10-31-2005 at 09:43 AM.
Wow. U have a nice TCCD there
Allendale E6300@2380mhz @1.28vcore(Vostok water cooling kit)
Asrock 775Twins-HDTV (ATi Xpress 300)
OCZ value 512mb x 2 @ 340mhz @ 4-4-3-5
IDE Hitachi 80gb 7200rpm 2 mb
Inno3D 7900GT
AOpen Combo 52x 32x RW 16x DVD
Panasonic Floppy
OCZ Power Stream 520 watt
icute casing with front blue CCFC, 2 80mm rear casing fan and 1 80mm casing fan on top.
My Gskill Pc4800 512mb dual channel kit does 325Mhz(DDR650) 2.5-4-3-6 memtest86 #5 stable
http://www.no-ip.freehosting123.com/upload/325mhz.jpg
but they do only 260 2.5-3-3-6
Last edited by Maxtor; 10-31-2005 at 05:05 AM.
3000+ Venice (0516GPCW) @ 2700Mhz 24/7
MSI Neo2 Platinum (Korea Nf3 chipset)
2 x 256Mb Gskill Pc4800
Club3d 6600GT AGP @ 612/1255
Boxed cooler
3000 Venice @ 2948Mhz (suicide)
Thank's these were my review set,the retail run's just as good.I have 1 more set of ram to review for G'skill at this time and then both of them go to the home page to be posted Thank's G'skill cant wait to get more boxes from ya!
@bb mods
i can't see the pics above
Feel free to contact ustech@gskillusa.com or use our G.Skill Q&A Sub-Forum, if having any questions about G.Skill products
Check out our items on NewEgg
pics are working for meOriginally Posted by G.S Technician
Intel Rig
2500K @ 4.8 Ghz 1.304v | ASRock Z68 Extreme3 Gen3| 2x4Gb Ripjaws DDR3-2133 | Radeon 7970 @ 1250/1800 | Corsair HX850 PSU
Custom Water of course
yeah i can see it now!Originally Posted by Absolute_0
good result bb mods
Feel free to contact ustech@gskillusa.com or use our G.Skill Q&A Sub-Forum, if having any questions about G.Skill products
Check out our items on NewEgg
if you send me a pack, i can upload 3 reviews of diferent 2x512mb g.skill ram
2x512mb le
2x512mb fc
PC4800 TCCD LA 2x512MB
Looked nice, but couldn't pass 286MHz stable, due to 875i chipset limit. I eventually found out the chipset is allergic to TCCD, and only really likes Hynix passed them speeds!
Dude, that's only 2x256 and just memtest 86.Originally Posted by Maxtor
We've already seen DDR690 from 2x256 completing SuperPi 32M.
Report back when you top this.
Asus Crosshair V Formula-Z | FX 8350 | 2x4GB Trident-X 2600 C10 | 2x ATI HD5870 Crossfire | Enermax Revo 1050watt | OCZ Vertex 3 60GB | Samsung F1 1TB
Watercooling: XSPC Raystorm | EK 5870 Delrin fullcover | TFC X-changer 480 w/ 4x Gentle Typhoon | DDC2+ Delrin top | EK 200mm res | Primochill LRT 3/8 tubing
Case: Murdermodded TJ-07
sub 9 sec. SPi1M 940BE 955BE 965BE 1090T
my new review will be posted on the face page of xs soon
that will be very nice too seeOriginally Posted by BB mods's
Feel free to contact ustech@gskillusa.com or use our G.Skill Q&A Sub-Forum, if having any questions about G.Skill products
Check out our items on NewEgg
Bookmarks