Originally Posted by uranium
Do you think the Molex is important? You've been at this sort of thing longer than I have....
I just tried 2.5 3 3 8. No go even at 3.1 volts. Lots of errors in Memtest. Then no post on return to previous settingsBut I fixed eventually, several CMOS clears + a battery removal later
It says it adds stability to the baord, so why not?
{2012 27imac-3.4i7-680mx-32gb ram-768SSD+External TB Samsung840pro ssd + TB velociraptors-Moto828mkIII/Marantz/Amphion Sound-HPzR30w 2nd monitor}
hehe, i've got same RAM as you - I'm stuck at 290 (haven't tried 295 like you) it can't seem get it stable at 300HT, I tried OPB's settings, still no go, any setting suggestions? WE GOTTA MAKE THIS RAM >= 300!
try 2.5-4-3-7-1T 2.9v
{2012 27imac-3.4i7-680mx-32gb ram-768SSD+External TB Samsung840pro ssd + TB velociraptors-Moto828mkIII/Marantz/Amphion Sound-HPzR30w 2nd monitor}
Right now I got my winnie at 250x9, but I want to check something before I go further. Does anyone else get ridiclously low CPU temps? I'm at 250x9 with 1.425vcore and I'm idling 30c with stock heatsink. Ambient temp is 65 F. Also my chipset temp is 40c, when it this too high?
Last edited by apu673; 02-08-2005 at 10:19 AM.
1.425 vcore idle @ 30c sounds right on.
No go xgman :/ Thanks for the tip though300mhz 1:1 HT is eluding me :/
Last edited by ominae; 02-08-2005 at 02:25 PM.
A64 3200+ 0450TPGW @ 300x8.0 1.4v
1GB OCZ 3200 Platinum EL R2 @ 300 2.5-4-3-7 2.9v
DFI Nforce 4 SLI-DR
XFX 6800GT
580W Topower 686P6
PC-60 LianLi
Does the Corsair 3200XL Pro suck with this board?
I havent seen any results.. except AMDnewbies results...
I really dont have the money for some nice OCZ now..
|| AMD64 3200+ @ 2550MHz || DFI nForce3 || Corsair TwinX1024 3200XL PRO || Antec Neopower 480W || X800 Pro VIVO @ XT PE || 3DMark01SE: 26705 || 3DMark03: 13246 || 3DMark05: 6279 || Prime stable || But... 3500+ Winchester, DFI nF4 Ultra, Powercolor X850XT on the way!
I wouldn't think so, I think Corsair 3200XL v1.2 (i think its 1.2) is on the new brainpower pcb - I'm sure it'll scale pretty well, just that OCZ/G.Skill have better chances of reaching high speeds
A64 3200+ 0450TPGW @ 300x8.0 1.4v
1GB OCZ 3200 Platinum EL R2 @ 300 2.5-4-3-7 2.9v
DFI Nforce 4 SLI-DR
XFX 6800GT
580W Topower 686P6
PC-60 LianLi
I got my DFI nForce 4 Ultra-D 2 days ago, but haven't tried it until yesterday. Now I can't get it too boot, while everything works on my Gigabyte K8NF-9. The thing is I'm using a PCI video card now (Voodoo 3), cause I'm waiting on a X850XT PE.
Does anyone know, or can anyone test if this board works with a PCI card.
Lian Li V1000 | OCZ Powerstream 600 Watt
DFI Lanparty nF4 SLI-DR Expert
Opteron 148 @ 2200Mhz
Mushkin RedLine PC4000 | 250Mhz 2-2-2-5
2 x XFX 7800GTX (500|1275)
74GB Western Digital Raptor/2 x Maxtor 300GB SATA
Dell 2005FPW 21" Widescreen Monitor
3DMark 2001SE - X850XT 40.4K Air Cooled Card
3DMark 03 - 7800GTX 18.3K Air Cooled System
3D Mark 05 - 7800GTX 8.5K Air Cooled System
Redline3D
Try doing a Cmos clear. I could not get mine to boot either until I did.
Viper
.
8800 Ultra to 756x1944/1260 ViperFang-IV Water Cooled
.
2900XT to 992/1197 ViperFang-IV Water Cooled
.
8800GTX to 756x1784/1161 ViperVenom 245w TEC Cooled
.
7800GTX-512's to 742/2106
.
7800GTX-256's to 650/1620
.
Pictures at www.imageevent.com/marginjohn/viperjohn
.
Contact JohnHillig@Earthlink.net for Modding Information and Support.
I did a CMOS clear, with the jumper, I'll try and get the battery out tonight, but I'm not sure if it's mobo or PCI card related, if it's not PCI related I might have gotten a faulty board....
Lian Li V1000 | OCZ Powerstream 600 Watt
DFI Lanparty nF4 SLI-DR Expert
Opteron 148 @ 2200Mhz
Mushkin RedLine PC4000 | 250Mhz 2-2-2-5
2 x XFX 7800GTX (500|1275)
74GB Western Digital Raptor/2 x Maxtor 300GB SATA
Dell 2005FPW 21" Widescreen Monitor
3DMark 2001SE - X850XT 40.4K Air Cooled Card
3DMark 03 - 7800GTX 18.3K Air Cooled System
3D Mark 05 - 7800GTX 8.5K Air Cooled System
Redline3D
hi
im using old sis 8mb pci card, works fine for me. had first some problems to boot cause sticked mem to wrong slot. dual channel belongs to the red slots, single channel to the red slot more away from cpu. what shows the onboard led ? does the pci card work in other machine ?
Last edited by psycho303; 02-09-2005 at 02:36 AM.
PCI card works on my other mobo, all 4 leds are burning, and I get no sound from the speaker, I enabled it with the jumper, mobo's DOA I guess...
Lian Li V1000 | OCZ Powerstream 600 Watt
DFI Lanparty nF4 SLI-DR Expert
Opteron 148 @ 2200Mhz
Mushkin RedLine PC4000 | 250Mhz 2-2-2-5
2 x XFX 7800GTX (500|1275)
74GB Western Digital Raptor/2 x Maxtor 300GB SATA
Dell 2005FPW 21" Widescreen Monitor
3DMark 2001SE - X850XT 40.4K Air Cooled Card
3DMark 03 - 7800GTX 18.3K Air Cooled System
3D Mark 05 - 7800GTX 8.5K Air Cooled System
Redline3D
To all Dfi Nf4 Bh5/VX Ram Users!
please can confirm somebody running BH5/VX rams on the NF4-DFI with 3.4v or more voltage on non PR-board ???
me and an other user having problems with higher voltages on that ram results in mem-test errors on the "same" adress, what is un-typical for overclocked ram. on other users machine the errors disapear when lowering mem voltage. on my machine one of the mushkin bh5 starts to get errors on same adress when i set to 3.4v. but mine even apears when lowering voltage , looks like it somehow broken. i really would like to know experience from other users, cause dont wanna kill my fresh RMAed-VX kit.
my theory is that the mem controller of my 3000+ which reach 2.65Ghz prime stable is weak and somehow killed my mushkin. sorry for bad english
you checked the ram slots ?PCI card works on my other mobo, all 4 leds are burning, and I get no sound from the speaker, I enabled it with the jumper, mobo's DOA I guess...
Yeah, the orange ones 2&4 are dual channel, but I also tried all the other slots...Also tried running with 1 stick only, nothing helps though.
Lian Li V1000 | OCZ Powerstream 600 Watt
DFI Lanparty nF4 SLI-DR Expert
Opteron 148 @ 2200Mhz
Mushkin RedLine PC4000 | 250Mhz 2-2-2-5
2 x XFX 7800GTX (500|1275)
74GB Western Digital Raptor/2 x Maxtor 300GB SATA
Dell 2005FPW 21" Widescreen Monitor
3DMark 2001SE - X850XT 40.4K Air Cooled Card
3DMark 03 - 7800GTX 18.3K Air Cooled System
3D Mark 05 - 7800GTX 8.5K Air Cooled System
Redline3D
my memory works fine with 3.5 or 3.6vplease can confirm somebody running BH5/VX rams on the NF4-DFI with 3.4v or more voltage on non PR-board ???
me and an other user having problems with higher voltages on that ram results in mem-test errors on the "same" adress, what is un-typical for overclocked ram. on other users machine the errors disapear when lowering mem voltage. on my machine one of the mushkin bh5 starts to get errors on same adress when i set to 3.4v. but mine even apears when lowering voltage , looks like it somehow broken. i really would like to know experience from other users, cause dont wanna kill my fresh RMAed-VX kit.
my theory is that the mem controller of my 3000+ which reach 2.65Ghz prime stable is weak and somehow killed my mushkin
The problem IMHO is the memory controller.
it is @ 0.13 or 0.09 and it doesn't work fine with 3.5v or more.
the mobo doesn't matter...
No go xgman :/ Thanks for the tip though
Make sure your on 0201 bios.
{2012 27imac-3.4i7-680mx-32gb ram-768SSD+External TB Samsung840pro ssd + TB velociraptors-Moto828mkIII/Marantz/Amphion Sound-HPzR30w 2nd monitor}
are people still having problems with usb devices?
on which cpu it runs with 3.6v on your machine ?my memory works fine with 3.5 or 3.6v
The problem IMHO is the memory controller.
it is @ 0.13 or 0.09 and it doesn't work fine with 3.5v or more.
the mobo doesn't matter...
fixed my usb problems, it was the hub
3500+ winchester.
But it is a worst cpu... it cant go upper than 2550...
yeah, mine respond best at 3.2v opposed to my previous 3.5vplease can confirm somebody running BH5/VX rams on the NF4-DFI with 3.4v or more voltage on non PR-board ???
me and an other user having problems with higher voltages on that ram results in mem-test errors on the "same" adress, what is un-typical for overclocked ram. on other users machine the errors disapear when lowering mem voltage. on my machine one of the mushkin bh5 starts to get errors on same adress when i set to 3.4v. but mine even apears when lowering voltage , looks like it somehow broken. i really would like to know experience from other users, cause dont wanna kill my fresh RMAed-VX kit.
my theory is that the mem controller of my 3000+ which reach 2.65Ghz prime stable is weak and somehow killed my mushkin
HELP.........at boot this always flashing: "warning : Have option ROM can not be invoke (vendor ID: 10D Eh Deivce ID:0057h)"
It is happen to anyone? What it means? I'm using ultra-D with 02/5 bios and tccd 431...and htt300 stable at 3.1V
Last edited by Dumo; 02-09-2005 at 07:27 PM.
Mine does that every once in a while, especially when going into the bios. Have you manually set your nvidia MAC address in the bios? Mine stopped saying that AFTER I manually set the MAC (don't ask, don't know why its not automatically set in the bios like every other board I have ever owned was!?!?)HELP.........at boot this always flashing: "warning : Have option ROM can not be invoke (vendor ID: 10D Eh Deivce ID:0057h)"
It is happen to anyone? What it means? I'm using ultra-D with 02/5 bios and tccd 431...and htt300 stable at 3.1V
Okay, found some very interesting and weird things tonight with my system. If you recall, I mentioned back on page 1 I believe about needing 3.1v on the G.Skill LE TCCD to pass Memtest #5&6, and to get the board to boot. Well, tonight after reading over at DFI-Street with 1 of the guys board having issues running test #8, I thought I give it it a try. Well, guess what? 3.1v errored out almost instantly. Than, I tried running SuperPI 1m and it errored always between test 13-16. Remembering OPB's settings and him using 2.6v, I tried that and whala! Memtest passed #8 looping for over 40 minutes. It was always failing in test #8 at 756mb and 9?? meaning it should be my module in bank 4 (correct?). I swapped modules around to see if I could get it fail in bank 2, but the same address failed again. Apon further investigation, I noticed that dimm slot 2 get plenty of blowoff air coming from the XP120 and 120mm fan, but slot 4 gets hardly any. Looking through the XP120, you can see slot 2 through the fins of the heatsink, but not slot 4. If we could use slots 1 & 3, it would get more airflow off the XP120. I don't think the Zalman's would have this problem as their design is radial. For those looking into air cooling, you might want to take a look at either the 7000 or 7700 instead of the XP120. I really do think that your memory slots will get better airflow with them, compared to the XP120.
For those wondering, I was able to swap memory positions just fine without taking off the XP120. I had plenty of room to get the G.Skill LE's out and back in!
Posting Permissions
Reply With Quote
