U got work to do hipro.....i'll get you a zippy for mod....good work man
U got work to do hipro.....i'll get you a zippy for mod....good work man
And another wonderfull mod from hipro
Would it be possible to unsolder the pots and hook them up to the side of the psu like the 3.3V trimmer? Or would this be a bad thing because of the longer wires?
Also, with the 50k trimmer, what exactly is the adjustable voltage range?
and another thing : this 'll work for the 6700 and the 6701 right?
Last edited by kristos; 02-19-2005 at 08:06 AM.
Halt On : No Errors
My cup is half full, yours is emtpy... now THAT's optimism
horum omnium fortissimi sunt Belgae: A64 FX OC record on Dry Ice by Jort, kristos, troid, C_X and "Moortgat"
Originally posted by lazyman
You are in trouble only if you admit it. Intel is never in trouble.
Originally Posted by TROIDX
INTEL PWA FOR EVER
Dr. Who my arss...
.........
Originally Posted by kristos
Yes it whould be possible to unsolder the pots and buy 3 of 25 turns and replace them with the mods too in the back of the PSU ......Only thing to take care of though , should be to put the inside cables as far away from any Mos-Fets and coills in there as possible........It should work fine......
As for 6700 and 6701 models I think that they should be identical......
INTEL PWA FOR EVER
Dr. Who my arss...
.........
Hip: If i were to Remove all 3 Pots, and Replace them with VR's What OHm rated pots would i use for each line?
I do not remember the exact Οhms of each pot BUT You can unsolder them and take a look at them.......Do the mods and you are ready.......The Voltages will be as I measured with the mods.....Originally Posted by Dissolved
INTEL PWA FOR EVER
Dr. Who my arss...
.........
Originally Posted by conrad.maranan
yeah, how come?
looking good as usual too bad that psu is a chunk of change
Well Worth it thoOriginally Posted by JSU
I got a new Zippy 700w. And it run fine with 5v jumper enable. vdimm up to 3.6v no problem.
http://www.bicker.de/englisch/produk...SL-6701P_e.pdf does any notice anything??? the starter is not on pin4,if u got a 20pins on a 6701p
BIG THX to you hipro5!
Did all the mods to my Zippy and also replaced the 12V and 5V trimmers on the PCB with some multiturn trimmers that I mounted on the PSU's frontplate. Additionally I replaced the awfully loud 0.52A 92x92x32mm SanyoDenki fan with 2 Papst 92x92x32mm fans with 0.245A each. Mounted one in the front like the Sanyo and the scond one at the back of the PSU to create a push-pull scenario. Cut out an opening for the fan at the PSU's backside. Now I can trim 12V, 5V and 3.3V from the outside and have the supply running a lot quieter than stock while still keeping it really cool. Will post some pics of my mods the next days.
THX again.
Quote from one of our professors:
"Reality is hiding in the imaginary part."
Thanks for the fan suggestion, Celemine. This is exactly what I was looking for...the stock fan is a total pain.Originally Posted by celemine1Gig
OK, here are some pics:
BTW, my Zippy is a little different from the ones that you should have. Mine is a special version, made for Tyan Server racks. It had less cables (soldered in some more), which were also much shorter than normal. Addionally the power connector is not located inside the PSU, but on the outside as you might see. But technically there should be no difference other than that.
Quote from one of our professors:
"Reality is hiding in the imaginary part."
Bookmarks