cant see ram settings in bios f6 ga p35-ds3r

[robber123]

i have been running this ga p35-ds3r mobo for a few days now.
e6850 cpu
ga p35-ds3r mobo
2gb crucial ballistix 6400
ultra-120 h/s
winxp pro
it ran straight away at 3.0ghz.
went into bios f6.59(dont know much about overclocking)raised the fsb from 333 to 365fsb.memory frequency is now 854.so my cpu now runs at 3.290ghz
raised the spd to 2.0,i think that is for the ram?
when in mit,i cant seem to see the ram settings,do updated bioses reveal those settings?
cpuz gives my ram settings as.
dram frequency@ 365
fsb dram@1.1
cas latency@5 clocks
ras to cas delay@5
ras precharge@5
cycle time@17 clocks
i understand, 6400 mem runs at 4 4 4 12.
how do i set those timings in bios when i cant see them?
i would like to try for 3.6ghz,but dont know how,apart from raising the fsb.havent touched the other settings in mit.
my temps are in mid 30s for cpu,and inside case.
hoping for someone will be patient and help me out here,as i know it can be stressful to help someone who is new to these bios.
thanks.

[hstuehmeyer2000]

boot into the bios and hit control+f1 and then go to the overclocking section

[robber123]

boot into the bios and hit control+f1 and then go to the overclocking section

hstuehmeyer2000;2652749
thanks for info.
just been into bios,and found the ram settings by going into dram settings,it was on auto.
i put it in manual,and it read.5.5.5.18
should i put those settings for my ram,which is 4.4.4.12,if i want to overclock more,from 3.290ghz as it is now.
or just raise the fsb from 356 fsb?
another point is,i cant see the voltages for the psu,as i would like to see the +3v,+5v.+12v
thanks.

[Leeghoofd]

You can put those ram settings mate 4-4-4-12 (if they are foreseen by Crucial, not all PC6400 ram runs at 4-4-4-12 some do only 5-5-5-15), just make sure ya ram gets the appropriate voltage then ( auto in bios sets it at 1.8 volts) and runs at 800mhz (unless you want to OC the ram speed too but for 400FSB it will be 2x for 800 speed)...

You can put in 400FSB and run 3.6ghz with ease (most E6850 do that with 1.4volts easily, most even with less), might need a bit more on the MCH voltage (+0.1)...

[robber123]

You can put those ram settings mate 4-4-4-12 (if they are foreseen by Crucial, not all PC6400 ram runs at 4-4-4-12 some do only 5-5-5-15), just make sure ya ram gets the appropriate voltage then ( auto in bios sets it at 1.8 volts) and runs at 800mhz (unless you want to OC the ram speed too but for 400FSB it will be 2x for 800 speed)...

You can put in 400FSB and run 3.6ghz with ease (most E6850 do that with 1.4volts easily, most even with less), might need a bit more on the MCH voltage (+0.1)...

leeghoofd2653184.
sorry i havent posted earlier.
been out doing the christmas rounds,and getting the booze down.


i understand what you are saying,very clear advice.
im going to crucial web,just to make sure it does run at 4.4.4.12 first,then i will try and do what you told me.
i will let you know what happens.
thanks for the advice.