i think this is going to be my last post regarding my kit of 1GB VX.....
i officially announce that one of my sticks has to be damagedi've seen it dying very slowly until my Neo2 finally refused to boot with it
unfortunately i made a mistake of removing heatspreadersand i can say - $260 well wasted
Last edited by bachus_anonym; 12-22-2004 at 10:24 PM.
What did you do?!?!?! Do you have another system you can test the "dead" VX on? Reset your CMOS and see what happens. A dead VX module after just 5 days totally blows, dude.
EDIT:
Did you notice it starting to "die out" after you removed the heatspreaders? I bet you something else accidentally came off along with it.
early today i had them both running @ DDR512 again... soon after i couldn't do DDR400 anymore....
then i tested both sticks in couple of my other NF2 boards - NF7-S v2 and DFI Infinity... that one stick started to error out on NF2 no matter what timmings and voltage. then i decided to give it one last go in my Neo2 and then i booted but i got that "BIOS checksum error"... i thought i corrupted BIOS so i flashed Neo2's chip in my Infinity, put it back in Neo2 and got same thing... swapped sticks and it booted just fine.... running memtest DDR520 as we speak.... without it's other half, though
well, it sucks.... to be honest with you, that's the only piece of PC hardware that ever died on me...
EDIT: i think i'll try to sell that one good stick somewhere and get another set as soon as they became available again.... unfortunately, it seems like it's the only way out as apparently "no RMA for me"...
EDIT2: actually, those problems started before i got heatspreaders off... i thought that it might be heat issue and then decided to remove heatspreaders.... i examined both sticks very carefully and nothing seems to be missing.... i guess, that was not a good idea
Last edited by bachus_anonym; 12-22-2004 at 10:35 PM.
Off topic, but I just noticed that your ICs have OCZ markings on them. Mine are clean and blank - totally void of any marks.
interesting.....Originally Posted by conrad.maranan
ok 258 seems to be the ssweet spot! water is awesome
sorry to here abotu that broi think this is going to be my last post regarding my kit of 1GB VX.....
i officially announce that one of my sticks has to be damaged
unfortunately i made a mistake of removing heatspreaders
i think that there are plenty of people that would like to get ahold of 512mb of VX!
Last edited by aCidbAbY; 12-23-2004 at 01:16 AM.
It look like mister OPP has proven that the boards are at fault in teh VX and running dividers. His VX is now running the 166 divider in his NF4 board.
http://www.xtremesystems.org/forums/...467#post643467
Boy I'm glad I am waiting for NF4 instead of jumping to NF3.
I can't wait to get my VX on the NF4~!
It look like mister OPP has proven that the boards are at fault in teh VX and running dividers. His VX is now running the 166 divider in his NF4 board.
http://www.xtremesystems.org/forums/...467#post643467
can i buy 2 512mb kits of VX instead of 1 gig and run it in dual channel just like normal 1gig ? or they have to be 1 gig matched pairs?
you probably could since ive done it with other brands but wont it end up being more expensive...
not really, maybe £5, but they ran out of 1gig kits in UK, only have 512mb VX left, so if i can, I will buy two to make it 1 gig
Posting Permissions
Reply With Quote
Bookmarks