9500pro sapphire PCB volt mods

[Malachia]

malachia, if you get to a point where u cant make the mem go any higher, i can tell you the other two mem vmods.

i haven't do mods yet, however...

[blinky]

i haven't do mods yet, however...

i hit 435/340 3dmark stable on my card today


thats with crappy air too (vga silencer)
got anything to counter that?

[Malachia]

malachia, if you get to a point where u cant make the mem go any higher, i can tell you the other two mem vmods.

wich kind of bastard
ok, the first that reach 20k is crazy man

[Malachia]

http://service.futuremark.com/compare?2k1=8282171

[blinky]

wich kind of bastard
ok, the first that reach 20k is crazy man

20K should be here on sunday, and 435/340 is with NO vmods either

this is fun.
cant wait til we both get vapor cooling on the gpu

[Malachia]

20K should be here on sunday, and 435/340 is with NO vmods either

this is fun.
cant wait til we both get vapor cooling on the gpu

435 without mods???

[blinky]

435 without mods???

YEP

[Malachia]

YEP

but with tec on gpu, i hope

[blinky]

but with tec on gpu, i hope

no just air, we'll hit 450-460 at least on the tec

[Malachia]

malachia, if you get to a point where u cant make the mem go any higher, i can tell you the other two mem vmods.

my dear friend, now i s the moment, plz tell me all the mods/tweak you know, in a month cpu will be @-80 and vga @-50

[blinky]

my dear friend, now i s the moment, plz tell me all the mods/tweak you know, in a month cpu will be @-80 and vga @-50

here you go...

i think these mods are unreleased until now

[Malachia]

hem...haw i can use them???

EDIT

what pot you used for VREF and VDDQ???

[blinky]

hem...haw i can use them???

EDIT

what pot you used for VREF and VDDQ???

20K is a safe bet, but you could probably get away with using 10k ones.

id use 20k for all three, u can always get lower resistence, but with a 10k u cant get higher than 10k, lol

[Malachia]

lol, and for the core what pot you used????

[blinky]

lol, and for the core what pot you used????

10K

[Malachia]

ok, then, i su 10k for the core as in the first pic, then 20k for all the other mods in the last pic....

[blinky]

ok, then, i su 10k for the core as in the first pic, then 20k for all the other mods in the last pic....

sounds good, cant wait for results

[Malachia]

chopper will arrive in a week or two, r404 for the prommy next week...


ah, and will arrive also an AS8 and an E0

[Malachia]

here you are

[Nazaar]

thats a very neat job !!

[Malachia]

in a day or two i will complete the mod, now i am working on cooling....

[blinky]

in a day or two i will complete the mod, now i am working on cooling....

.

[<Wouter>]

Has any one did +5v and ground booster mods on their 9500pro? And how about adding caps for stabillity? I can get my 9800se 9500propcb up to 400/375 without mods, but when did the vgpu and vmem a while ago i had to set my clocks lower than before :S . I've got watercooling on my gpu and good mem cooling so i think the internal power circuit can't deliver the amps to my gpu and mem at high voltages.

[Malachia]

done!

now, vgpu&vddr all ok, vddq and vref didn't seem to wok....i lower trimmer but nothing changes....

[blinky]

Has any one did +5v and ground booster mods on their 9500pro? And how about adding caps for stabillity? I can get my 9800se 9500propcb up to 400/375 without mods, but when did the vgpu and vmem a while ago i had to set my clocks lower than before :S . I've got watercooling on my gpu and good mem cooling so i think the internal power circuit can't deliver the amps to my gpu and mem at high voltages.

i tried soldering wires directly to the solder points on teh back of the card, and it didnt do anything for my clocks

i actually had power problems as well, and they were solved by getting a higher watt power supply. hehe

i would suggest adding caps though, it might help