voltmaster

[Crankster]

Pats his An50R...

[Tony]

Eric(back at the office) ran 4V on some although that may be a little excessive.I will ask a few questions for you and hopefully get some answers.

[thephenom]

Is it true that these are unmarked winbond chips of some sort? Perhaps the leftover inventory winbond had before closing down?

[Mongoose420]

Is it true that these are unmarked winbond chips of some sort? Perhaps the leftover inventory winbond had before closing down?

he allready said repeatedly that they are not going to release what ic's these are. give the guy a break allready.

[OCZEric]

More Voltmaster stuff....2-2-2-10 at 260FSB on the MSI K8N Neo 2.

[Rabbi_NZ]

that's real nice, is that 260 2-2-2-10 at 3.2v?!

Looks a bit like Mushkin TCCD...
TCCD 2-2-2-5 @ 255mhz @ 3.3v

[Nanobot]

NICE!

ETA when it's going to be available ?
Or are you guys just testing the waters ?

[ryanpgroovy]

testing the waters for now ,

[saaya]

Same question here, Saaya. I'd like to see how they'd run with 3.4v. I just upped my 3.3v line to 3.5v, so I've got some pretty decent voltage available.

doesnt the dfi use the 5v rail to create vdimm? 0_o

and be carefull with the 3.3v rail! bowman said he killed several a64s with a too high 3.3v rail of 3.6/3.7v!

and those results look really nice! really really nice!
what will the average sticks do with 3.2v? 250 2-2-2? 250 3-2-2?
or is this the result from an average stick of those ic's?

[WeStSiDePLaYa]

doesnt the dfi use the 5v rail to create vdimm? 0_o

the nf2 boards did. but the new dfi UT uses the 3.3v rail. there are modded bios that will let you use vdimm .1v less than your 3.3v rail is at.

[OCZEric]

and those results look really nice! really really nice!
what will the average sticks do with 3.2v? 250 2-2-2? 250 3-2-2?
or is this the result from an average stick of those ic's?

This was an average pair. Most shouuld be able to do this speed on the MSI board anyway. On the P4C800 the max speed is quite a bit lower..."only" 225.

Actually, I think I may have been capped at the max our MSI Neo2 could do, as I have just found out that I can't get anything to work over 260 now.

So it is possible that it could go even faster. It'll have to wait for a new Neo 2 though. I'll post when I get the new board in.

EDIT: Also, this was with a pair of modules (note the dual channel in the pic)

[Nanobot]

Nice but only 5 loops of #5 test is hardly considered stable.

Care to post a screenie with 50+ loops of #5 done when you get the replacement mobo ?

[Tony]

Nice but only 5 loops of #5 test is hardly considered stable.

Care to post a screenie with 50+ loops of #5 done when you get the replacement mobo ?

We will do...the more you juice em up the higher they go.

[MaxxxRacer]

why are the aidia results so low comparatively?? running in single channel.. and is that 2-2-2-2 timmings!!

[ryanpgroovy]

Weird about the everest results , exspecialy considering AIDAlatency score is so good

[saaya]

whats wrong with sciencemark? always thougt its the best alternative fro sandra...

[Tony]

They are not that low really, remember this is 1 modules single channel.Sandra buffered is FSB driven more than bandwidth, the unbuffered is bang on though as my EB at 280 gives 2600+.

The everest latency got me though, thats the lowest i have ever seen.

[drunkenmaster]

didn't, errm, was it bigtoe when he basically announced the plat rev 2 and the plat 3700 say both were tccd? isn't that what ryan is pointing out, best stuff goes in the higher rated ram? If thats the case then shouldn't everyone be buying that and not the 3200 rev 2 so much?

(can't remember if ryan tccd talk was last page or other thread, went from one to the other and canne remember)

[pythagoras]

Hi Bigtoe,

I recieved one of your ddr boosters in the competition ran on this site recently. Thankyou very much . I'm about 35 minutes from Manchester city centre, wouldnt mind meeting up if you have time to discuss optimising ram based on your booster coupled with sub zero temps. Have any experiments been done with ram at those temps?

Regards

John.

[WeStSiDePLaYa]

so did OCZ drop these or what?

[saaya]

so did OCZ drop these or what?

what makes you think so?

[enzoR]

well tccd is doing really well atm... i dont think there is much point in this

[Holst]

well tccd is doing really well atm... i dont think there is much point in this

Unless its quite a bit cheaper....

I dont wantto pay for TCCD, its not worth the money over my Bh5.

[Tony]

We haven't dropped it m8, TCCD does 245+ 2-2-2 when rammed with voltage, this stuff just keeps going...260+ with ease and im sure you guys will do even better

[Nanobot]

Does this mean it will be released ?

Sorry to ask again but I'm going BH-5 route if the *OCZ PC3200 Voltmaster LE Gold * (a seems like that would be a good name,no?) are not going to market.