A8V and OCZ EL PC3200 PE Rev 2?

[Section8]

Since my problem got buried in the other thread:

OK I have finally done some testing and I can't get this memory up past 255 1:1 with 2.5-3-3-10 1T? I did get it to boot at 260 once but it crashed soon after a Sandra run. I hit 7,200. I have the boards VDIMM maxed at 2.8? Any suggestions? I have the HT at 800 and the multiplier is at 9 to take those both out of the equation. On a side note I am running at 240 X 12 now with 2.5-3-3-10 1T and getting 7,300 in Sandra. I know I can get more out of this RAM but I don't know what is holding me back. Are there other memory settings I need to change? Thanks..

[Drisler]

Try 2T
1T limits my 512megs to 255 as well

[dav]

did you try setting HT at 600?

BTW, i believe the performance drop in 2T doesn't worth.. so i always OC with 1T.

[xgman]

Consider yourself lucky. Mine blue (or back) screened as soon as I removed my Balistic 4000 which ran in the a8v at the same stable speed as the EB3700 253 2.5-3-2-8 in this board, and tried them in both slot sets. Since the rev 2 failed right away at the same 2.87 volts, it's outta here. Very let down.

[Section8]

Yeah I tried 600 HT as well.

[`schr0et]

HTT doesn't make a difference on the K8T800 boards, I've tried going from 1K to 600 with no difference in stability with 1T.

[dav]

is it possible to have 1k (5x) HT multiplier with 260 HTT?
that's a 1300 HT speed...

[pre]

For 250HTT I needed to use LDT x3, 294HTT I can use x2. Not really stable 110% stable after 294. My one doesnt really like anything above 800HTT.

[`schr0et]

I used 1000 HT with 260x11 it was prime stable for 8 hours so yeah it works fine.

[dav]

nice one...

[Section8]

I used 1000 HT with 260x11 it was prime stable for 8 hours so yeah it works fine.

Maybe I should try the newer BIOS. I am still on 1006. I can't really get over 250 stable with 800HT and 1:1 at 2.5-3-3-10 1T? I will try the new 1007 bios and see if for some reason I can get a little higher?

[dav]

oh yes i recall that my TCCD would do at most 251 HTT on a8v... while the same stick would do more than 280 HTT on gigabyte k8nsnxp-939...

perhaps the a8v doesn't like TCCD......
let me know how are you going with it..

PS. I have the 1007 BIOS.

[Section8]

oh yes i recall that my TCCD would do at most 251 HTT on a8v... while the same stick would do more than 280 HTT on gigabyte k8nsnxp-939...

perhaps the a8v doesn't like TCCD......
let me know how are you going with it..

PS. I have the 1007 BIOS.

So you like the Giga board better then? I will buy another motherboard if it means I can get higher clocks. I was looking at the Giga and the MSI but decided on the Asus Rev 2 because it seemed like it was the most stable. This is my 3rd Mobo. I had 2 Rev 1.02's the 1st had working AGP/PCI locks with the Beta BIOS but died after a week for no apparent reason? It just stopped working? Then the RMA resulted in another Rev 1.02 that wouldn't lock the AGP/PCI with the BEAT bios so I bought the Rev 2..LOL so 3 down what's next? The Giga NF3 or the MSI NF3?

[dav]

it seems to me that TCCD would work better on gigabyte than on asus.