WELL.......NOW guess what THIS does....Warning 56K / photos...

[hipro5]

any informations about this "project"?

Nope.......sorry.....It's secret for now....

[Nosfer@tu]

Unfortunatelly the DDR Maximizer doesn't "leave" us much profet......We hope our 2nd project will, which will show up before XMAS......

At least you are building a company now
So the money and time spendt will be less for the next product, BTW thank god you are comming up with more products :p

[Revv23]

[B]

You'll get one don't worry.....

Hehe on the preorder!!!

I hope tankguys does engraved faceplates i emailed them about it, waiting on the reply.

[Rol-Co]

On p5b deluxe seems to be ok (from 4+ users so on).........on Biostar don't know.......upload a picture arround the DDR slots so as to see it.......

i will if i get the camera back in a few days.... waus-mod /petervandamned and me doing a o/c demo here in holland, the maxi is there to show and a little promotion for you....

[hipro5]

i will if i get the camera back in a few days.... waus-mod /petervandamned and me doing a o/c demo here in holland, the maxi is there to show and a little promotion for you....

That sounds GOOD........Thank you.....

Hehe on the preorder!!!

I hope tankguys does engraved faceplates i emailed them about it, waiting on the reply.

We'll see what can we do about you......Black face plate?....

[Revv23]

That sounds GOOD........Thank you.....



We'll see what can we do about you......Black face plate?....

Yes indeed sir.

[hipro5]

Thank God and AFTER 14 days of travel, the DDR Maximizers are now in USA at TankGuys in stock......

[G H Z]

Yes they are

[GoriLLakoS]

Hipro...does maxi plays ok with Striker?
Or we need to unsolder the coil?

[G H Z]

I need to know this for P5N32-E also, same board basically, here's a shot of it.

[hipro5]

On ASUS Striker - as is - it may work and it may not......I couldn't figure out what was happening during reboots.....I had to UNSOLDER the DDR coil so as to be 100% sure that I'll be OK.....
One word.....Either Striker's Vdimm is crap OR Maxi does a GREAT job on it....


EDIT: This is the coil that must be removed.

[Speederlander]

Does P5WDG2 WS Pro have a similar concern as Striker?

[moonlightcheese]

[Speederlander]

So I have to desolder/remove that specific coil and that coil alone? I want to be very clear. Thanks.

[Kin Hell]

Yeah George, you been lucky enough to get this board & test the maximiser on it yet?

All the best for the New Year m8y!

[hipro5]

So I have to desolder/remove that specific coil and that coil alone? I want to be very clear. Thanks.

EXACTLY as shown in the picture above.....Desoldering that coil will do the job......You can ONLY desolder it's ONE leg though and lift it up - it's the same -

Yeah George, you been lucky enough to get this board & test the maximiser on it yet?
DFI Lanparty UT ICFX3200T2R/G RD600
All the best for the New Year m8y!

Not yet...
Happy new year to all....

[G H Z]

Thanks for that hipro

So for future reference how can I tell if a board needs the choke removed or not? Is it in the way the maximizer operates or something else?

[hipro5]

Thanks for that hipro

So for future reference how can I tell if a board needs the choke removed or not? Is it in the way the maximizer operates or something else?

You must measure the DDR circuit of a mobo to see if any of the output Mos-Fets has a grounded leg.....If one of them has it's one leg short circuited to ground, it's safe to remove the DDR coil so as to be sure.....
If there isn't such a case and you don't see any DDR Mos-Fets to ground, then the mobo is about 98% compatible.....

[Enz0]

DDR Maximizer doesn't work well with LANPARTY UT ICFX3200-T2R/G.
It shows current Vdimm correctly, but it cannot change the Vdimm.
LANPARTY UT ICFX3200-T2R/G has two coils near the dimm slot.

Which coil should I remove?

[Revv23]

it's best you wait for hipro, but my bet is on the big one.

[hipro5]

There you go.......

[Enz0]

There you go.......

http://www.thelab.gr/images/Hipro5/M...FX3200_jpg.jpg

Thank you.
I'll try to remove it.

[Enz0]

I removed the coil but the Maximizer didn't work.
It showed 1.07V or so, and didn't change whatever I do.

[hipro5]

Try this: http://www.hipro-tech.com/forums/viewtopic.php?t=3 and if it still doesn't work, PM me.....

[loopy83]

Sorry for reanimate this thread.... bus the Maximizer is allready updated
Is there a reseller for Germany?

Will the DDR+VTT PCB work with Asus P4C800 Series?

I am just a poor student, but i will sell some things to get such a Maximizer

I am intereted in a package of Maximizer with DDR+VTT PCB (if its work with my board).... later with DDR3 PCB.... i hope may current system will outlast the DDR2 era

@ Hipro: thanks for your PMs.... i hope some other guys can answer my questions... so you have more time for your own stuff

Loopy