I know is not a top score over here , but for me is been a long fight to get this score.....
No mode GPU, cooled just by fresh water
http://service.futuremark.com/compare?2k3=3138583
I know is not a top score over here , but for me is been a long fight to get this score.....
No mode GPU, cooled just by fresh water
http://service.futuremark.com/compare?2k3=3138583
Well done!
I like all the saved scores, remind me of my long walk to 22k in 2k1...
DFI NF4 Ultra-D @ 300HTT | A64 3000+ Winchester @ 2.4GHz 1.61V | 4x256MB BH-5 (HyperX+CorsairXMS) @ 240MHz 2-2-2-5 3.1V | Club3D X800XL ViVo @ 452/540 | XP-90 | 92mm Tornado | Silencer5 | Enermax 460W | 2k1: 30419
congratulations
Asus A7N8X-E Deluxe
Athlon XP 2800+ Barton @ 3200+ (200x11)
Mushkin DDR400 BASIC 2*512mb
Albatron GeForce 6600GT 128mb (Being Repaired)
Samsung SyncMaster 730BF 17" (4ms RT, 600:1 CR)
woa 1.4ghz
i even see artifacts on the desktop though :P
whats the max clean run you can get without artifacts?
clean at 1.400 start to art at 1.420
wow! 1.4ghz memory? That's the fastest I've seen, by a lot. How did you get there? Are you saying you didnt do any hardware mods to get that memory speed? That's amazing!
You say you artifact at 1.42, so this run had artifacts?
Also, that is quite a nice overclocking cpu @ stock voltage.
I got just an edited bios.. 1.5v and the danger den WB. so I can coll even the ram.
1 question, you have a peltier on your GPU?
The God Father OC.Team
No pelt on my card. I have done 505 core a couple of times...Its the memory which I dont understand. I know the DD block covers the ram, but I was under the impression that the ram needed more volts not cooling to get above 1.30ghz. You have shattered that notion. What could your memory do before you watercooled with DD block? Ive had my memory temps super low (cold room, huge fans, etc), and always hit a wall exactly at 1.30ghz. No matter what, no higher. You are basically the first person to get significantly above 1.30 ghz that I've run into. Nice work.
1320 stok cooling. use to bench at 1330....
wath your temperature? at idle and under load? if I remeber in an old 3d did you had a low temperature, do you use cold water on it?tnx.
The God Father OC.Team
Great score man .
Only one question man , insane memory speed , what´s the cooling ?
The prommy at load what temps ?
on the vaporator around -37°
the gpu 40° by fresh water at 20°
The God Father OC.Team
my temps are crazy good, like yours. I use the swiftech mcw50 block, basically the entire kit with two radiators. The cpu is on a different circuit. Under normal circumstances (72f room temp) my idle gpu is 31-34c, with load around 40-43. If I bench, I can get my idle to about 27-30c, and the load in the high 30s with colder room temps and a large external fan. Good for stable 505 core, but 1.30ghz mem is it!Originally Posted by detonator
The memory has been stuck at 1.30ghz no matter what. Is it possible that your card has more volts going to memory somehow? Perhaps via the bios? Either way, that is just sick dude, seriously.
off topic: anyone notice the post counts aren't changing?
stupid me nevermind
Last edited by drcrawn; 09-21-2004 at 08:57 AM.
I dont realy undestend, at idle I have 40° under load still 40°....Originally Posted by drcrawn
I dient use any sistem for that score , I just plugged the wb to the tap cold water and it was about 18-20° the water I think ...so I had a constantly 40°.Dunno why I cant get lower then 40 ° do you suggest anything?
Last edited by detonator; 09-20-2004 at 02:25 PM.
The God Father OC.Team
tahts what i thought at first too, but thats not what hes talkin bout,Originally Posted by µnrealneo²
look by the left side of the CPU-Z screenie
can you see the light? is it shining too bright? can you see the light at the end of the tunnel, i know i do, i know its true.
Congrats Detonator
Is the OCZ EB running at 1:1? How? How many volts, what timings?
Asus P4C800ED P-M 730@2.8 7700Cu
2X1GB OCZ - ATI X800XT AIW - OCZ PS 520W
stock cooling on the card.
i ran 3:2.. thats a littlebit lame.. 2-2-2-6
Last edited by dpa; 09-21-2004 at 04:07 AM.
nice!
, oh... the scores not bad either
Asus A7N8X-E Deluxe
Athlon XP 2800+ Barton @ 3200+ (200x11)
Mushkin DDR400 BASIC 2*512mb
Albatron GeForce 6600GT 128mb (Being Repaired)
Samsung SyncMaster 730BF 17" (4ms RT, 600:1 CR)
my ram is 2ns and wont go past 1180. i thought that was good. when i get my new mbo ill be back up, 03 is one of my favoutite benches. only at 12800 now tho, stock.
Anfortunaly,My modded asus is on the way dso I benched with the Max3 no mod... so I cudent overvolte the rams ...Bus 272 1:1 3-3-3-5 2,9VOriginally Posted by NoX
The God Father OC.Team
the highest i could do is 1.38Ghz.. 1.39Ghz = lockup in mother nature.
DPA and Det, : How are you setting memory clocks? Rivatuner, coolbits only? Are you forcing these clocks or do you test them through coolbits etc... thx.
Hey DrCrawn!Originally Posted by drcrawn
I set memory speed with powerstrip.. i cant set 1.38Ghz in coolbits.. 1.28Ghz is the highest the "test" will allow.
dp
lol, thats a good idea, using constant fresh water...Originally Posted by detonator
I'm suprised that you cant go less that 40 with that, but 40 is still very very good load temp. My only suggestion (and this is what I do for highest scores) is to get a large fan and blow air directly onto the card. The fan I use is 2500rpm 12inch diameter. Its very powerful and the video card loves it. In combination with 19c room temps, it makes for some great cooling. I did back to back 3DMark03 runs @ 505/1.30 stable.
So while the WB is key, the fan really does help and cold room temps too, which means cold water temps...at least for a while...
Bookmarks