Vapochill LS and Mach ST/GT test part1

[Marquzz]

Stille little confused about the price. vandamned claimed the price is €799 for LS and €849 for GT but the asetek dude said it was $877 for LS and $1400 for GT?

[AndrOvr]

Originally posted by Hawk
Here is w/ small FFT's.

HOw much heat load is that? I guess not 240w, and the evap is almost at -25c ..

Didnt Asetek tunned the LS for -25c @ 240w ... ????

[pkrew]

The best price I found on the LS was $828. They're usually $878. The GT is selling for $1250 at kit-tronics w/o the AL kit. The AL kit is $150. I suppose thats how he got $1400. The LS comes stock in AL. The other issue I suppose would be the cpu kit which the LS has both and only one with the GT. The extra kit cost about $100

[ant1]

Looks quite accurate. The 4ghz P4 should have around 100-150w.
If you look at
petervandamned´s screenshot you´ll see the evap temp is -28 and the cpu temp is -16. That´s about the same temps the chart shows.

[Marquzz]

Originally posted by AndrOvr
HOw much heat load is that? I guess not 240w, and the evap is almost at -25c ..

Didnt Asetek tunned the LS for -25c @ 240w ... ????

mm, but the temps is going to stay at -25 all the way to 240W

[Marquzz]

Originally posted by pkrew
The best price I found on the LS was $828. They're usually $878. The GT is selling for $1250 at kit-tronics w/o the AL kit. The AL kit is $150. I suppose thats how he got $1400. The LS comes stock in AL. The other issue I suppose would be the cpu kit which the LS has both and only one with the GT. The extra kit cost about $100

Guess that nventive is much more cheaper here in Europe then, lucky us

[pkrew]

Looks that way. Lucky you guys. Pretty big price diffierence here. Hard for me to justify the cost of an LS let alone what would amount to $1500 for the GT.

[comment]

I've also run some test on my Vapo LS in this thread over at Asetek's fourm.

What I find amazing is that my results show that the LS is very good at holding the evap temp going from idle to load, the difference being only about 3°C! That's simply impressive.

But I must say that I'm impressed also with the cooling capacity of the Mach II GT, as shown here. Looking forward to be seeing Part Two petervandamned :thumbsup:

Btw: Plz include som evap temps in Part Two (for the LS don't use the WinCC readings as it shows temps 4°C too high).

[Gamer]

nice one Peter.

[twilius_basic]

Originally posted by charlie
Since Asetek claims the LS functions better with higher heatloads, let me make a suggestion:
When I ran my Prescott 3.0E to 4609, the Dry Ice was sublimating as fast as I could add it to the tube. At 1.9V, the Prescott is a veritable inferno. SOOO, replace cool running 3.4C with a Pressie and see what happens Now THAT'S a torture test!!!!!!!

C

OMG 1.9v on Prescott! What mobo was that under? It had to have been about ready to explode and screaming for mercy!

[SAE]

Looking good, peter

I am saving up for a GT and I think I won't regret it...

Hope I get my mach1 repaired by nventiv soon (maybe I get it to work on a graphics card ) as I only wait for instructions from their support

They're nice and already 've got my claim report (confirmed that)

[megahurtz-oc]

man i have to call bs on that -16 temp with the ls ive ran two differnt cpus on my ls 3.0c and a3.2ee full loaded after 2 hours my temp from a calibrated fluke was never warmer than -25c your test sounds alittle biased............

[Soulburner]

Originally posted by megahurtz-oc
man i have to call bs on that -16 temp with the ls ive ran two differnt cpus on my ls 3.0c and a3.2ee full loaded after 2 hours my temp from a calibrated fluke was never warmer than -25c your test sounds alittle biased............

He is using the motherboard sensor though, there can be a big difference.

[Hawk]

Originally posted by megahurtz-oc
man i have to call bs on that -16 temp with the ls ive ran two differnt cpus on my ls 3.0c and a3.2ee full loaded after 2 hours my temp from a calibrated fluke was never warmer than -25c your test sounds alittle biased............

Send me your Fluke and I'll check my temps. I'm using the MB sensor right now.

[comment]

Originally posted by megahurtz-oc
man i have to call bs on that -16 temp with the ls ive ran two differnt cpus on my ls 3.0c and a3.2ee full loaded after 2 hours my temp from a calibrated fluke was never warmer than -25c your test sounds alittle biased............

Could you fill us in on the detailes of your testing megahurtz-oc?

[Soulburner]

Besides it can't be "biased" if he was using the same board for both tests. The only variable that changed was the cooler, so it doesn't even matter if the temps are wrong or not.

[Hawk]

Comment,

You are DeCay, Right?

If you have the Fluke setup, what is the temp your motherboard is reporting on the CPU?

I also ran the Prime95 Test as above with the Small FFT's and my load's are similar to the reviewers results. I wish I had a GT to test along side mine also.

[Assasin-uk]

Some interesting findings here....


Look out for the Official xtreme systems review on the front page coming soooon, an old pro will be doing the review.....

[Marquzz]

Coming soon? Hasn't it been out for a while now? Read it several hour ago...

[megahurtz-oc]

Originally posted by comment
Could you fill us in on the detailes of your testing megahurtz-oc?

i could fill you in but i hardley think anyone would take me serious in fact im pretty sure there would be some people that would try and discredit me and im not up for getting flamed today.

[tombman]

Hi guys..

Different question for nventiv (viggen?): has the cap tube been changed for the GT or is it just a refill with r404a?

And this one is for the guys that knows about danfoss compressors: is the SC18CL better or the SC18CLX?

Please help, because soon i will have a Mach I with one of those compressors modded into

[megahurtz-oc]

as for the temp on my mobo sensor it ranges between -32 and
-22 under same load thats why i setup the fluke sensor directly under the cpu. who is decay? i have always gone by my current name.

[xsky]

Originally posted by comment
Btw: Plz include som evap temps in Part Two (for the LS don't use the WinCC readings as it shows temps 4°C too high). [/B]

Sure? I thought the value with WinCC running would be the accurate one.
I can't believe my Eva is currently -49c cold with a 1,45V Prescott in

[megahurtz-oc]

i dont use wincc as i have my usb ports all disabled.

[Lithan]

Originally posted by Marquzz
Guess that nventive is much more cheaper here in Europe then, lucky us

It's cause our dollar is a piece of crap right now. Makes me feel like a canadian. Four more years of Bush and I'll start speaking spanish and wearing a sombrero. Ole!