**[Official]]** ASRock z87 OC Formula + (M) Thread

[moorhen2]

Hi msimax, not been able to boot @ 2666, If I remember I could boot @ 2600 one time, but not even managed that since, lol, that was using the the 2600 pre-set in the bios, 1.92v tight if I remember.^^^ Above screen, very nice.

[msimax]

thx man see where the regular psc profile takes you because i have a set of X-psc thats only good for 2400

[moorhen2]

Using the "PSC normal 1.65v" pre-set in bios, seems to help, taking cpu ratio and uncore out of the equation for the time being. 2200 @ 1.65v as a starting point.

[moorhen2]

Now at 2400 @ 1.65v, everything else @ stock, looking good for now.

[emertX]

My fastest clocks I ever reached on my golden haswell....that board clocks like hell...too said I haven't made my mems cold!

And here's the outstanding 3d performance!!! Next step is memories cold and much more oldschool 3d!

[emertX]

Nice Board for Samsungs also!!!

[bullant]

Was just messing around today testing few different things,training ect PSC,Z87 OC Formula
cl6-10-6-26-2871Mhz


cl5-9-5-24-2660Mhz


cl6-9-6-26-2800Mhz

[l0ud_sil3nc3]

Bully!!!!!

Killing it as usual man, time for that new thread in a few days

[bullant]

Bully!!!!!

Killing it as usual man, time for that new thread in a few days

Yeah mate,looking forward to that new thread

[msimax]

just got another cpu 4.6 doable on water but havent tested mem controller yet, this is that last chip im gonna bin lol imma hold out for Devils Canyon

[bullant]

Good luck with the new chip msimax,you got a great board for the job and don't forget the new OC Formula coming

[msimax]

Good luck with the new chip msimax,you got a great board for the job and don't forget the new OC Formula coming

thanks now just see if i can find some time now lol but is it me or do the z87 boards looker cheaper..

[moorhen2]

Corsair Dominator GT 1600 C6, Elpida Hypers, going to see what they can go up to, @2000mhz 1.8v, using the "Elpida Hyper" preset in bios.

[msimax]

will asrock release a bios to allow 4790k to work on this board?

[ZenEffect]

Corsair Dominator GT 1600 C6, Elpida Hypers, going to see what they can go up to, @2000mhz 1.8v, using the "Elpida Hyper" preset in bios.

good hypers can run 2400 c7 on this board.

[samsarulz]

will asrock release a bios to allow 4790k to work on this board?

I?m looking for the same. Will take a 4790K only if is fully supported by Z87 Formula OC /ac. If overclock control is disabled, then there?s no point. Devil?s Canyon is not like a proper upgrade. Is faster Haswell, but that don?t guarantee better or higher OC . As what I have read, most chips can?t go up beyond 4600 MHz. A little disappointing.

Binning Haswell is a waste of money :8 Binned 6-7. All were bad clockers.

[AVulgarPicture]

Hmm, I could do with an answer on DC support too. I'm getting ready to load up on pentium anniversary editions, and might bin a 4790k or two as well. Just depends on if I need a new motherboard or not.

[msimax]

crickets is the sound lol

[l0ud_sil3nc3]

Hmm, I could do with an answer on DC support too. I'm getting ready to load up on pentium anniversary editions, and might bin a 4790k or two as well. Just depends on if I need a new motherboard or not.

DJ has all ready posted 4790K screens on the Z87M OC Formula so I assume it all ready works with current bios's.

Have not seen any screens of the G3528 on the Z87 OC Formula yet . . .

[Nizzen]

Is there a DC Bios ready when 4790k retail is coming Tuesday?

[l0ud_sil3nc3]

Is there a DC Bios ready when 4790k retail is coming Tuesday?

Every bios from 1.6 up should work, so really no need to update your bios:

[C-N]

Is there a DC Bios ready when 4790k retail is coming Tuesday?

My AC board works fine with the latest release but I did notice there's a new bios for the Pentium available for my board. Didn't check other boards.

Z87 OCF AC BETA BIOS 1.81 "Update C0 microcode to support Pentium Anniversary"

[msimax]

sounds good ill pick one up

[l0ud_sil3nc3]

Hyper fun!

[Shiranui Gen-An]

4790K working great on this board for me, running BIOS 1.91. Another thing to note, VDIMM is darn near spot on; BIOS set 1.9160 and 1.917~1.918 checked with DMM.