[XS] GTX TITAN Owners Club

[cowie]

I think so far from my results dan its best to just try this guy maarten12100 bios at ocn's titan thread\
http://www.overclock.net/t/1363440/n...ners-club/3310
he has a couple bios in the thread one even has 1.24v full time(without added .37 in ab)so really start there.

If you want to go and do mod just to have fun with mod after that i tell you as best i can in more detail its easy
I just get kick out of doing the mods i need to to them for my fix,results normally come hand in hand with them but this time not so much
Just like picture shows
50K vr to the point marked in the pic it also shows him using one of the legs off power plug for ground.
He shorted two of the 5m0 power sence resisters also
You need vread also, that i went to inductors to get.(in pic i put up a few pages back)It all happens on front of card so stock cooler no go

So just try bios first then post up results of them

[emertX]

Which bios is the 1,24?
He posted a lot!

[cowie]

hold on i look now i renamed it

Think it was this one
in post 3286
but i think maybe clock issues hmmm or was it this post 3312 one that was more better?

Try to see i went thruogh a few.

[emertX]

and this will give me 1,24V without mod??

[cowie]

1.22 then add 37 mv with ab up to 1.249 read live with dmm

[emertX]

And which one is it?
#1, #2 #3?

[cowie]

stay away from 3(since 1 guy bluescreens with it) use the ones in the other #posts as i said they all behave same way in 3d

Please dan go right to him with any input on bios would help all that way.

[emertX]

I tried 1 and 2...but voltage change through ab wouldn't help...It doesn't work...it goes all the way back to +0!

[cowie]

Give me a minute i will read voltage on them i think its no matter you still get 1.24
hold on

[cowie]

Tested #2

Its ok dan you dont need to move slider
idle 2d lp3d 1.223v in 3d 1.249v without slider so your go to go

[emertX]

So you mean, not shown in AB, but v?a dmm?

[emertX]

works!

[cowie]

So you mean, not shown in AB, but v?a dmm?

Works!

Yes read with a digital voltage meter,ab(alex got too pissed with noobs asking why volts go up and down lol) and all software is just in ballpark.
Not to get too complcated,it does matter some on where your gpu read and ground is with your dmm but i went with the logical spot.

See that was easier then hardmod right.
Now try vantage at 1300

[aussie-revhead]

Tested #2

Its ok dan you dont need to move slider
idle 2d lp3d 1.223v in 3d 1.249v without slider so your go to go

So that No2 bios will give me 150% power and 1.249v ?? woohoo I will try it after I put my water block on.

He posted a pic guys of the vgpu mod a few posts back. Post 138.

Nice score there aussie Sure you don't want to try SLI, I know where there's a card, your wife won't even notice

Thanks mate, I did a little better too, still with 24/7 and gaming clock on cpu:

P15436 http://www.3dmark.com/3dm11/6152854

[cowie]

yEs it has that voltage but pl is read upwards of only 108ish%

[emertX]

looks promising...doesn't it?

[PedantOne]

looks promising...doesn't it?

looks good, but whats about throttling? My Titan hates higher volrtage = throttling/bad performance

[GoldenTiger]

Tested #2

Its ok dan you dont need to move slider
idle 2d lp3d 1.223v in 3d 1.249v without slider so your go to go

Can you confirm what post # that's from?

[aussie-revhead]

Is that right? 1.2v 2D also? Does it still down clock in 2D or is that why the voltage stays up?

[cowie]

Is that right? 1.2v 2D also? Does it still down clock in 2D or is that why the voltage stays up?

No down clock on some i tried see post below

Can you confirm what post # that's from?

i will take a look becuase i went thruogh a few this morning he was poping them out fast .
Some have too high of a clock for mere motals
I will get back to you if dan does not answer first.


Some bf3 action at 1250 have some vids at 1280 too will post later
http://www.youtube.com/watch?v=Gdgi4FcUBcE

[pinto]

Tri Titan





I get my best results with stock bios, one of my cards hate voltage and throttle a lot with 1.2+
Best result in sli:

[aussie-revhead]

Cowie - are you on stock cooler or water? If you find a bios that gives a voltage bump and still downclocks 2D I will try it, I have an EK VGA supreme in my loop waiting to go on. Two nights ago I benched easily at +200 but last night it would lock up or bsod at +180 so maybe lower temps will make it more consistant.

[BababooeyHTJ]

I can now say for sure that these cards aren't hardware capped. I just hit a 125% power limit, my ups seems to back up those claims.

[nossy23]

Anyone else getting the "DirectX function "GetDeviceRemovedReason" failed with DXGI_ERROR_DEVICE_HUNG: Device hung due to badly formed commands.. GPU: "NVIDIA GeForce GTX Titan", Driver: 314.90" message when playing? I also tried the lasted beta drivers, same thing happens.

I first had a GTX 580 and had no problems. I upgraded to Geforce Titan, even used drive sweeper, and only installed the newer drivers. I can't get rid of this problem. On average it happens every 5 hours or so.

I monitored my videocard and it's not getting too hot or anything. It's also not overclocked. Is this a HW problem or SW?

[NapalmV5]

KEPLER BIOS TWEAKER V1.25 download

http://www.technic3d.com/download/ov...aker-v1.25.htm


Naennons bios that works great for some at ocn

http://www.overclock.net/t/1363440/n...#post_19490729