LIAN-LI Pitstop T 60
Here we are ready for yet another adventure, well going to take 'into consideration a feast of Lian-Li.
Fasten your seatbelts
Do not smoke
prepare the popcorn
Following the beer
and .......... good vision at all
Ermanno
Let's start with posting the material, the case
Continue the presentation of the case:
OCZ Power Supply
Now we will examine the power supply from 750w un'OCZ that will go 'part of this mod
Asrock motherboard
now we move to the motherboard necessitudine staining I chose this card, fits perfectly with the mod and certainly will make 'his voice heavy lifting the cpu frequency to very high levels
And the adventure continues, but I'm going to submit another Harware, but rather the essential components that will dissipate the Lian-Li
We start with the arrivals from Aquatuning
We begin with the pump, is a Koolance PMP-300 is the small but pushes much
Now we turn to the flow, but this will be 'only visual, but there will be' a controlled dall'Aquaero xt
As I said this is only a factor esthete and will be 'enlightened, I removed the original and I placed an LED RGB LED
You guys are a step above the lines, we are speaking of red anodized aluminum passive heatsinks, small Carello of photos and for working in the next post
I can not put the thermometer and the fans are from Micro 40x40mm, rock 'also add the liquid of Nanoxia
Consider the passive heatsinks, as you see them coming, then for them to adapt to my mod I had to do some little hole
Armed with the tip of 3.25 and male M4 I am going to do one of the first working
Ok place, the processing of the thermometer in the upper eheheheh
Then you get a nice clean job I fitted a piece of paper tape that I put where I am going 'to cut to fit, and with a little' of sound patient I cut with the DREMEL
We're back to upload, today we examine the so-called shark fins term given by friends, guys here the work is long and containing many photos, I hope 'they just do not fall asleep ahahahahaha
Before processing "Aluminum" we speak of a panel dell'ACRyan satin black and a red
Working as a first line them with the 80mm nastrocarta whole area of ??work, in my experience I know 'that the only film sometimes is not enough to protect from scratches especially if using jigsaws.
Once coated is passed to the drawing or tracing on the panel, is preparing the work area (a chair with 2 planks of plywood) and the work begins
Here is the most 'delicate tracing of the holes of the fans are cutting and bending
Drilling ...............
And here are the twins ready for further processing
Here now we continue to place the media as the first finished work
Now, let us casting off, bending, it affects the side so as not to incur abnormal folds and then with a little 'tug of war .... and the fold is ready
Beat the fans are 40mm and see what comes out ........
First phase was successful, the second pass, we prepare the coating media
Once assembled, we see that effect are also illuminated
We see a beta assembly:
We support over a bit of hardware and see how it feels
First test lights
Coupling media
Moving on to the actual installation
Let's talk about the base, and even the fans are 40mm should be able to get some air, but from where?
begin:
1
2
3
4
5
6
assembled
Air outlet fans are
arrivals
Fittings
LED
Ok mount fittings
LED changed from blue to red, very good for the mod.
Indeed removed the system's magnetic flowmeter sensing koolancee added a nice red LED with extension and 2-pin plug fan, resistance is hidden inside the flowmeter
Carbon arrived ..............
And then it just works in wax pack in a piece of carbon cloth as standard .... manopoli the fantastic as you think, we will see some good in the future ............. However, here we are once more work with the pieces 'large 250mm x 500 mm and down' processing ......... what do you think?
as someone pointed out to me the difference of red aluminum I have radically changed the facade.
Posting Permissions
Reply With Quote
Bookmarks