Looking Detail Baby Monster "ASUS MAXIMUS V GENE"

[ZoLKoRn]

Old PSC chip still rock for Ivy Bridge, some quick play with my old PIS

2500MHz 7-11-7-28-1T (Latency Boudry =1)




2200/2250MHz 6-10-7-24-1T (Latency Boudry =3)


Uploaded with ImageShack.us


All nice for DRAM and M5G and will try again with 0078 bios

[bro20000]

Finally got 2600 out of G.skill TridentX 2400C10D only single sided mem




My old G.Skill F3-17600CL7D-4GBXHD are alot faster thou





Anyone got any tips to clock G.skill TridentX 2400C10D maybe am missing sommat.

[cheapseats]

Thanks for the 32m comparisons owikh

curious about low AIDA scores in the hyper run. 32m looks on a par with your PSC run so the actual performance seems to be ok.

Corsair DomGT 2000C7 @ 2400 8-8-8-25-1T 2x2GB

got my board and chip today

[owikh84]

Arghh i cant boot raid0 volume created with RIVE X79 on this M5G.
BSOD BSOD

when raid is enabled in BIOS my OS in AHCI SATA2 cant boot.

[bro20000]

Sub 30 latency my 1st love this kit

[ZoLKoRn]

Nice Latency you got bro20000 and well try to play about Latency Boudry it can boot up more BW for you

[bro20000]

Gotta a problem took oc abit far and am getting error code 72 tryed clearing cmos no luck.g
unner try us biosphere flashback any advice.

[NoGuru]

Gotta a problem took oc abit far and am getting error code 72 tryed clearing cmos no luck.g
unner try us biosphere flashback any advice.

Unplug PSU and pull the battery for about 30 seconds.

[rouvio]

Unplug PSU and pull the battery for about 30 seconds.

+1

I suggested few hours, but apparently 30 secs are enough. (lol I'm just scared to loose valuable hardware).
There was *nothing* this board did not recover from. yet.

[NoGuru]

+1

I suggested few hours, but apparently 30 secs are enough. (lol I'm just scared to loose valuable hardware).
There was *nothing* this board did not recover from. yet.

Well I have had to wait overnight after pulling the battery for it to fully clear but it should only take a few seconds.

I see you are in Ohio. Where at?
Over at OCN we are having a benching-Lan event in Toronto June 1st. Lots of LN2 to go around

[ante_ante]

What is the best, set manual voltage or use offset ?

[bro20000]

I prefer manual volts.

[Eldonko]

Heh heh, Oskar Wu may resent that but I agree. BIOS on this board is just awesome.

retail 3770k MVGEne
old ass psc pi black 2x2 kit.
any gains using the slots closest to the cpu or the outside slots?

I was talking to Dumo tonight and this psc kit..then dumo was like hey man try this out. the point im trying to make is shamino is the Oscar Wu of the current gen. I couldnt think of a higher compliment to give him. It is like being back on the DFI ultra D all over again. MVgene is basically DFI glory days of ram madness all over again. I fricken love this board! it Belongs in the hall of fame next to the DFI nf4 ultra D..

[rouvio]

That's it.
I'm all out of DICE

These are the fastest 3DMARK's I was able to achieve with the 3770K and my GTX 560Ti.

All submissions were recognized and accepted by FUTUREMARK.
All submissions were recognized, validated and approved by HWBOT.
No PPU, no Physx, No LUCID MVP.

-----------------

3DMARK01:

• HWBOT
• ORB - none. (no support)

3DMARK03:

• HWBOT
• ORB

3DMARK05:

• HWBOT
• ORB

3DMARK06:

• HWBOT
• ORB

3DMARK-VANTAGE-PERFORMANCE
NO PPU - NO PHYSX

• HWBOT
• ORB

3DMARK11:

• HWBOT
• ORB

--------------

[plane501]

anyone can tell me the detail of the "Tight 2x4GB Samsung" profile in the 0078 bios ???
I want all the timings,thanks in advance.

[plane501]

Not sure if quad kit is better, Im pretty happy with these.

Im so use to typing xtreme as in "xtremesystems", I didnt pay attention to the spelling of teamxtreem memory.

3770K@4.5G
team 2600c10 @ 2400 9 11 11 27 1T with tight second&third timings
faster than your 2800 10 13 13 31 1T

[NoGuru]

anyone can tell me the detail of the "Tight 2x4GB Samsung" profile in the 0078 bios ???
I want all the timings,thanks in advance.

Go into BIOS, set Tight, now go look at your timings.

[plane501]

Go into BIOS, set Tight, now go look at your timings.

I'm using P8Z77-v pro bro .......

[NoGuru]

I'm using P8Z77-v pro bro .......

I see, I will post when I get home from work if I have time. Have to pack to leave town but should have a few minutes to look.

[plane501]

I see, I will post when I get home from work if I have time. Have to pack to leave town but should have a few minutes to look.

Looking forward to it

[bro20000]

Loving this board just ashame ivy is so hot. Had to invest £300 in a waterchiller will go higher when that comes. Here a 4.5 prime stable.

[owikh84]

Finally my 3770K has arrived yesterday
Quick test with Team Xtreem 2600C10 kit

[ante_ante]

What program are u using to change timings in windows ?

[mav2000]

Hi guys am getting a post code of 25 and voltage is not helping anytime I try ram at 2600 MHz. I read Rajas guide and it says Imc may not be capable. This is with the new gskill trident x 8 gb kit as well as a 4 gb kit of gskill flares. I need 1.280 to run 4.5 ghz stable. Any help? Any other voltages to play with to get this going or to get CPU vcore down?

[mav2000]

can someone help? Thanks..