^^Thanks OC My luck with Asus board
At least I can learn to play BF3...if my C2 turn out to be a dud with cold
Last edited by Dumo; 02-09-2012 at 07:48 PM.
Is it safe to run 4.9GHz@1.48v 24/7 with temps under linx in the low 70c(This is max) Average temps under linx is 65-66C
I want the chip to last at least 2 years.
Asus Rampage II Extreme--Core i7 920@4000MHz (191X21)(1.36v HT off)-- 2 OCZ Solid SSDs in RAID 0--2.5TB storage--Asus Xonar D2 Soundcard--Radeon HD 4850--Corsair TWIN3X 1600MHz DDR3@ 1527MHz 8-8-8-22--Corsair TX750W--Mozart Tx--Termochill PA120.3--3X Papst--Clearflex tubing, 12mm ID-- Slightly modified Cuplex HD CPU block--Laing DDC 1Plus with pro top--Swiftech MCRES-Micro Rev.1
LinX or Prime95 cause a lot higher heat load, than regular aplication use. 70°C is very good temperature anyway. If you want be "safe" – try 4.8G with little bit lover voltage
AMD Athlon II 455, Phenom II 565BE/850/965BE/980BE, FX-8150 + WC kit, Athlon II 651K, A8-3870K Antec KÜHLER H₂O 920 ASUS Sabertooth 990FX, Rampage IV Extreme, EAH5550, GTX570DCII, GTX580 Matrix BENQ BL2400PT CORSAIR TX850M, Force GT 90GB CREATIVE X-Fi X-Treme Music Geil EVOTWO 2000C6 (PSC)
GIGABYTE 880GA-UD3H, 990FXA-UD5, 990FXA-UD7 (rev1.1), 8400GS, A75-UD4H, 7970OC, Z77X-UD5H KINGPINcooling Dragon F1 Gemini 2.0, Tek-9 FAT 6.0 Kingston HyperX T1 2133C9 2x2GB (Hyper BDBG), HyperX T1 2133C8 2x2GB (Hyper MGH-E), Genesis 2400C11 4x2GB, Blu 1600C9 2x4GB, HyperX SSD 120GB, DT HyperX USB3.0 64GB
Logitech G700 noctua NH-D14 SAMSUNG F1 1TB 7200 Seasonic SS-600HT Thermaltake Soprano RS101
Hey mate! Sorry for late reply. I was very busy, and at the same time very frustrated with Hypers on X79/SB-E.
People here were telling that these don't mix, but I was skeptical... Well, I should have listened.
There were some high numbers, but it was unstable. Couldn't pass AIDA64 CPU ZLib benchmark, not to mention SuperPI32.
If used with Hypers' profile from the BIOS, results were just terrible. AIDA's CPU Photoworxx and CPU AES, which are very memory dependent gave half and the quarter of the speed.
Sooo... While I was in trouble, I was looking for one particular memory kit for some time... And one day I saw it with 50% discount. Of course, I bought two kits for the price of one.
ADATA AX3U2400GB2G9-DG2 - Introduction - Description - Specification (yes, they are nonexistent in the specs )
Some results:
Maximus 5 Gene | i7-3770K @ 5GHz | ADATA 2x2GB @ 2.6GHz 9-12-10-28-1T | HD7970 @ 1200/6400
Rampage 4 Extreme | i7-3930K @ 5GHz ||| X58-A OC Orange | i7-980X @ 4.6GHz
Like the ram... Any chance of telling where you got them from.. very interested..
Case: M.M Ascension C.S
MB: Asus RIVE
CPU: 3960 24/7: 4900 @1.43v
Ram: 16 gig Dominator Platinum 2133 series ,@2450hmz 10.11.11.28 1.5v
Drive: OCZ RevoDrive 3 X2 240GB
Cooling: 2 x 560 SR1 + 1 X 280 SR1 single loop
Aquaero 5 w/NB PK3 Fans @ 900rpm. Koolance 380i w/. MCP355 x 2 XSPC top
Video: Titan Hydro Copper x 3 SLI
PS: 2 x Corsair 1200w
Maximus 5 Gene | i7-3770K @ 5GHz | ADATA 2x2GB @ 2.6GHz 9-12-10-28-1T | HD7970 @ 1200/6400
Rampage 4 Extreme | i7-3930K @ 5GHz ||| X58-A OC Orange | i7-980X @ 4.6GHz
Last edited by xarot; 02-11-2012 at 03:51 PM.
Core i7 Extreme 4960X @ 4.5 GHz, Asus Rampage IV Black Edition, 32 GB Corsair Dominator GT DDR3-1866 MHz, GTX 780 3-way SLI, Corsair AX1200, Corsair 700D, Corsair H100i, Corsair Force GT 180GB, Windows 8 Pro, Asus VG278HR
Core i7 Extreme 990X @ 4.4 GHz, Asus Rampage III Black Edition, 12 GB Corsair Dominator GT DDR3-1866 MHz, EVGA GTX 580 "Black Ops" SLI, Corsair AX1200, Corsair 650D, Corsar H100, Samsung 830 256GB, Asus ROG Thunderbolt, Windows 7 Pro
What is the safest voltage for 24/7 use? I searched for answers and some say 1.5v is the max for 24/7 others say don't go over 1.45. I'm currently running 4.8GHz @1.46v with RAM @2133MHz. Is this acceptable?
Asus Rampage II Extreme--Core i7 920@4000MHz (191X21)(1.36v HT off)-- 2 OCZ Solid SSDs in RAID 0--2.5TB storage--Asus Xonar D2 Soundcard--Radeon HD 4850--Corsair TWIN3X 1600MHz DDR3@ 1527MHz 8-8-8-22--Corsair TX750W--Mozart Tx--Termochill PA120.3--3X Papst--Clearflex tubing, 12mm ID-- Slightly modified Cuplex HD CPU block--Laing DDC 1Plus with pro top--Swiftech MCRES-Micro Rev.1
Intel I7 3970x @4.9GHz+
Asus Rampage IV Extreme
Corsair Dominator Platinum @2400MHz
EVGA GTX TITAN @1300MHz+
OCZ Vertex 4 256gb
EVGA SuperNOVA 1300w G2
EK-Supreme HF / RX360 RX120/MCP655 EK-D5
EK-FC TITAN
Corsair Obsidian 800D
Samsung 275T+ 1920x1200
Rampage-IV-Extreme-ASUS-1103
http://www.mediafire.com/?kbw58mbxaf8zqs0
- Improves High Frequency DRAM Compatibility
- Improves Peripheral Compatibility
- 14.02.2012
Need a Gigabyte latest BIOS?
Z370 AORUS Gaming 7,
GA-Z97X-SOC Force ,Core i7-4790K @ 4.9 GHz
GA-Z87X-UD3H ,Core i7-4770K @ 4.65 GHz
G.Skill F3-2933C12D-8GTXDG @ 3100 (12-15-14-35-CR1) @1.66V
2xSSD Corsair Force GS 128 (RAID 0), WD Caviar Black SATA3 1TB HDD,
Evga GTS 450 SC, Gigabyte Superb 720W
XSPC RayStorm D5 EX240 (Liquid Ultra)
NZXT Phantom 630 Ultra Tower
Win 7 SP1 x64;Win 10 x64
PROJECT :: The Xtreme (WET) Dream!!!
PERSONAL H2O BESTS :
E8600 @ 4.8GHz E6750 @ 4GHz QX9650 @ 4.6GHz i7 920 @ 4.6GHz
PERSONAL AIR BESTS :
Sempron140 @ 4Ghz (Stock Cooler) i7 3960x @ 5.4ghz (Air Cooler)
Bex : "Who said girls can't play PC games or overclock!? Do I look like your imagination!?"
Aaron : "TBH, a girl doing all that is a pretty perfect girl!"
Swift_Wraith : "could someone please check bex for a penis?"
Got myself 2 kits of Team Xtreem LV PC3 20800 DDR3 LV 2600 4X4GB Quad from memoryc
Can't make it to run at 2600MHz
what I've tried so far
load Normal OC profile
- use BIOS 006
- set BCLK to 122 and memory to one notch lower from 2600MHz, that's ~2200MHz
- go into DRAM option, set to mode 2, set main timings to 10-12-12-31-1T as well as 2T
- reboot and go into BIOS again to increase one notch memory to 2600MHz, vdimm 1.65v-1.7v, VTT/VCCSA 1.25-1.3v
- get code B2 (62) & 00
SUCCESSFUL TRADE LIST RM600k+
^^ Malaysia's Overclocking Enthusiast Community Website ^^
Find us at Facebook HERE
XS Successful Trades:
G.Skill RipjawsZ 2400C9 4X4GB - sold to easegantini | G.Skill RipjawsX 2133C8 2X2GB - bought from Dumo | 2600K 57X - bought from newhit | 3770K 6750 - bought from Viss | 3770K 6750 - sold to Sniper | 3770K IMC 2800+ - bought from Dumo | G.Skill Pi 2200C7 - bought from websmile | 3770K IMC 2933+ - bought from Viss | DomGT 2kC7 3X2GB - sold to _AntLionBR_ | G.Skill Pi 2133C8 - bought from websmile | DomP 2800C11 - bought from Alex-Ro | Pi 2000C7 - bought from websmile | GTX4 + KVR 1333C9 - bought from TaPaKaH
- get code B2 (62) & 00[/QUOTE]
b2 -> 00 = IMC cannot make the frequency, DRAM Training not even started yet
I'll give mine a shot tonight... I was going to buy another kit to get 32gb but maybe not now...
PROJECT :: The Xtreme (WET) Dream!!!
PERSONAL H2O BESTS :
E8600 @ 4.8GHz E6750 @ 4GHz QX9650 @ 4.6GHz i7 920 @ 4.6GHz
PERSONAL AIR BESTS :
Sempron140 @ 4Ghz (Stock Cooler) i7 3960x @ 5.4ghz (Air Cooler)
Bex : "Who said girls can't play PC games or overclock!? Do I look like your imagination!?"
Aaron : "TBH, a girl doing all that is a pretty perfect girl!"
Swift_Wraith : "could someone please check bex for a penis?"
SUCCESSFUL TRADE LIST RM600k+
^^ Malaysia's Overclocking Enthusiast Community Website ^^
Find us at Facebook HERE
XS Successful Trades:
G.Skill RipjawsZ 2400C9 4X4GB - sold to easegantini | G.Skill RipjawsX 2133C8 2X2GB - bought from Dumo | 2600K 57X - bought from newhit | 3770K 6750 - bought from Viss | 3770K 6750 - sold to Sniper | 3770K IMC 2800+ - bought from Dumo | G.Skill Pi 2200C7 - bought from websmile | 3770K IMC 2933+ - bought from Viss | DomGT 2kC7 3X2GB - sold to _AntLionBR_ | G.Skill Pi 2133C8 - bought from websmile | DomP 2800C11 - bought from Alex-Ro | Pi 2000C7 - bought from websmile | GTX4 + KVR 1333C9 - bought from TaPaKaH
Hi, I'm hoping Lard or Raja can assist me.
I was on BIOS 1005 and added a 3rd 580 GTX. I booted up and was greeted with an AF code almost immediately. System hangs, no VGA coming through. If I hit the reset switch it then cycles up and proceeds to a point where it says I need to go into the BIOS via F1 on the keyboard.
I go into the BIOS. All system settings are stock except I have set the RAID flag. It's reporting that it's trying to get to 9600 Mhz on turbo and the memory is set to 1600 Mhz. I freaked out a little bit. I then went into the next BIOS screen where the date is displaying as Thursday, 00/00/986X. I've tried changing this. So if I put in 16/02/2012 it automatically changes to Friday 33/1971547854 when I move the mouse or up arrow etc.
So ok I thought, I'll flash to 1101 in the hope it fixes it. So I flash it, it does the 100% thing. After it restarts it goes straight back into the AF code almost immediately. I hit the reset button and it cycles through, once again asking me to fix the BIOS settings. Once again, the date is wrong and loading defaults etc and restarting goes straight back to AF code, but at least it's only trying to get to 3900 Mhz turbo. All other settings stay the same. I try using the secondary BIOS (0604) and it does the same thing, the AF code, reset, BIOS needs to resaved, same story.
So ok, I reset the CMOS using the button on the rear of the motherboard. hold it down for approx 15 seconds. It goes back to the AF code on reboot and displays a 9600 Mhz turbo mode and same date issue in bios.
Ok so I turn off the machine and take the CMOS battery out for at least 3 minutes. Reseat the battery and fire it up. Same deal as above. This happens on either BIOS.
Is there some way to fix this in house or should I RMA it. Please note I've removed all peripheral devices (except keyboard) and removed all extra vid cards except one, sound card etc. One stick of RAM in the proper slot (it reports 4Gb found as it should) and still getting the same issue. I've been able to force boot off a RAID 0 setup into safe mode but cannot boot in standard mode. When I force boot using a selected drive I get an AE code while it loads drivers (Win7 64 bit Ultimate) and then AA for a bit, then it boots in, BUT have only been able to get into the OS once. It usually sits on 'Please Wait...' with AA on the debug led forever.
Can anyone assist? Is there any way to force it to reset the BIOS to a factory default or is there a more serious issue that I can return it to my place of purchase for examination by a professional?
Please help, it's been 3 days without a PC and I'm going insane.
Thanks.
reseat cpu use only one stick of ram one vga and boot after cmos cleared
check in bios hw monitor all the voltages and temps and take a SS
to see if anything is amiss in the hw monitor
It is normal after upgrading the BIOS asks you press F1 for reset to factory.
First I recommend that you upgrade to BIOS 1103 or 1201 because small fixes compatibility issues and stability.
Study carefully the values of the hard disk, graphics and memory, checking they are correct, do not do any overclocking, leave the values in AUTO.
A greeting.
Intel i7 3960x // ASUS Rampage IV Extreme // 16GB DDR3 // OCZ Colossus 120Gb // SLI GTX-580 // LG W2486L Surround // X-Fi Fatal1ty // OCZ ZX 1250w // Logitech diNovo Edge // Logitech G27 // Corsair Obsidian 800D // Win 7 Ultimate Sp1
Thanks Lard. I tried all that. I finally went and bought another R4E. Funny enough, the problem persisted. However over the last 3 days the problems have slowly gone away. I don't know if this points to a CPU issue or not, but today was the first time I could turn it on and didn't get forced into a forced F1 and manual boot off the primary OS HDD.
I appreciate the help and I will slowly start testing the system in OC scenarios.
Intel i7 3960x // ASUS Rampage IV Extreme // 16GB DDR3 // OCZ Colossus 120Gb // SLI GTX-580 // LG W2486L Surround // X-Fi Fatal1ty // OCZ ZX 1250w // Logitech diNovo Edge // Logitech G27 // Corsair Obsidian 800D // Win 7 Ultimate Sp1
My post from yesterday is gone...
Here we go again:
Here is a BIOS template for the OP, old school, txt file, as I don't like BIOS s/s.
Code:************************EXTREME TWEAKER************************ =============================================================== LN2 Mode Disable All Core Target CPU Turbo-Mode Speed : 5000MHz Target DRAM Speed : 2400MHz Ai Overclock Tuner [Manual] CPU Level Up [Disabled] BCLK Frequency [100.000] CPU Strap [100MHz] ClockGen Full Reset [Enabled] Turbo Ratio [By All Cores] By All Cores [50] Internal PLL Overvoltage [Enabled] CPU Clock Gen Filter [20UF] Memory Frequency [DDR3-2400MHz] Xtreme Tweaking [Disabled] EPU Power Saving Mode [Disabled] =============================================================== >DRAM Timing Control Rampage Tweak [Mode 2] Primary Timings CHA CHB CHC CHD DRAM CAS# Latency 7 7 7 7 [7] DRAM RAS# to CAS# Delay 11 11 11 11 [11] DRAM RAS# PRE Time 7 7 7 7 [7] DRAM RAS# ACT Time 27 27 27 27 [27] DRAM COMMAND Mode 1 1 1 1 [1] Latency Boundary [Auto] Secondary Timings CHA CHB CHC CHD DRAM RAS# to RAS# Delay 4 4 4 4 [4] DRAM REF Cycle Time 96 96 96 96 [96] DRAM WRITE Recovery Time 14 14 14 14 [14] DRAM READ to PRE Time 4 4 4 4 [4] DRAM FOUR ACT WIN Time 20 20 20 20 [20] DRAM WRITE to READ Dealy 4 4 4 4 [4] DRAM Write Latency 8 8 8 8 [8] Tertiary Timings CHA CHB CHC CHD tRRDR 0 0 0 0 [0] tRRDD 0 0 0 0 [0] tWWDR 0 0 0 0 [0] tWWDD 0 0 0 0 [0] tRWDR 8 8 8 8 [8] tRWDD 3 3 3 3 [3] tWRDR 1 1 1 1 [1] tWRDD 1 1 1 1 [1] tRWSR 8 8 8 8 [8] tCCD 0 0 0 0 [0] Latency Timings CHA CHB CHC CHD DRAM RTL (CHA D0 R0) 37 [Auto] DRAM IOL (CHA D0 R0) 5 [Auto] DRAM RTL (CHA D0 R1) 37 [Auto] DRAM IOL (CHA D0 R1) 5 [Auto] DRAM RTL (CHA D1 R0) 11 [Auto] DRAM IOL (CHA D1 R0) 0 [Auto] DRAM RTL (CHA D1 R1) 11 [Auto] DRAM IOL (CHA D1 R1) 0 [Auto] ----------------------------------------------------- DRAM RTL (CHB D0 R0) 37 [Auto] DRAM IOL (CHB D0 R0) 7 [Auto] DRAM RTL (CHB D0 R1) 37 [Auto] DRAM IOL (CHB D0 R1) 7 [Auto] DRAM RTL (CHB D1 R0) 11 [Auto] DRAM IOL (CHB D1 R0) 0 [Auto] DRAM RTL (CHB D1 R1) 11 [Auto] DRAM IOL (CHB D1 R1) 0 [Auto] ----------------------------------------------------- DRAM RTL (CHC D0 R0) 37 [Auto] DRAM IOL (CHC D0 R0) 5 [Auto] DRAM RTL (CHC D0 R1) 37 [Auto] DRAM IOL (CHC D0 R1) 5 [Auto] DRAM RTL (CHC D1 R0) 11 [Auto] DRAM IOL (CHC D1 R0) 0 [Auto] DRAM RTL (CHC D1 R1) 11 [Auto] DRAM IOL (CHC D1 R1) 0 [Auto] ----------------------------------------------------- DRAM RTL (CHD D0 R0) 37 [Auto] DRAM IOL (CHD D0 R0) 7 [Auto] DRAM RTL (CHD D0 R1) 37 [Auto] DRAM IOL (CHD D0 R1) 7 [Auto] DRAM RTL (CHD D1 R0) 11 [Auto] DRAM IOL (CHD D1 R0) 0 [Auto] DRAM RTL (CHD D1 R1) 11 [Auto] DRAM IOL (CHD D1 R1) 0 [Auto] Others DRAM CLK Period [5] Enhanced Training (CHA) [Disabled] Enhanced Training (CHB) [Disabled] Enhanced Training (CHC) [Disabled] Enhanced Training (CHD) [Disabled] MCH Duty Sense (CHA) [15] MCH Duty Sense (CHB) [17] MCH Duty Sense (CHC) [15] MCH Duty Sense (CHD) [17] Receiver Slew [Normal] Transmitter Slew [Normal] MCH Recheck [Auto] RC Warm Boot Fast [Disabled] =============================================================== >DIGI+ Power Control CPU VCore CPU Load-line Calibration [High] CPU Current Capability [Disabled] CPU Voltage Frequency [Manual] CPU Fixed Frequency [500] VRM Over Temperature Protection [Auto] CPU Power Duty Control [Extreme] Vcore MOS volt. Control [7V] CPU Power Phase Control [Extreme] CPU VCORE Boot Up Voltage [Auto] CPU VSA VCCSA Load-line Calibration [Extreme] VCCSA Current Capability [140%] VCCSA Fixed Frequency [500] CPU VCCSA Boot Up Voltage [Auto] CPU VTT CPU VTT Switching Freq [1.3x] CPU VTT Over-Current Protection [Auto] DRAM Voltage DRAM-AB Current Capability [140%] DRAM-AB Voltage Frequency [Manual] DRAM-AB Fixed Frequency Mode [500] DRAM-AB Power Phase Control [Extreme] DRAM-CD Current Capability [140%] DRAM-CD Voltage Frequency [Manual] DRAM-CD Fixed Frequency Mode [500] DRAM-CD Power Phase Control [Extreme] PCH 1.1V PCH 1.1V Switching Freq [Auto] =============================================================== >CPU Performance Settings CPU Ratio [Auto] Enhanced Intel SpeedStep Technology [Enabled] Turbo Mode [Enabled] -------------------------------------------------------- Turbo Mode Parameters Power Limit Control [Auto] =============================================================== Extreme OV [Disabled] BCLK Skew [Auto] CPU VCORE Voltage 1.432V [Manual Mode] CPU VCORE Manual Voltage [1.430] VTT CPU Voltage 1.218V [1.20000] 2nd VTTCPU Voltage 1.046V [Auto] CPU VCCSA Voltage 1.212V [Manual Mode] CPU VCCSA Manual Voltage [1.200] DRAM Voltage (CHA, CHB) 1.762V [1.770] DRAM Voltage (CHC, CHD) 1.762V [1.775] CPU PLL Voltage 1.884V [Auto] PCH 1.1v Voltage 1.096V [Auto] VTTDDR Voltage (CHA, CHB) [Auto] VTTDDR Voltage (CHC, CHD) [Auto] CPU Spread Spectrum [Disabled] PCIE Spread Spectrum [Disabled] =============================================================== >CPU Tweakers'Paradise PCIE CLK Skew [Auto] CPU I/O Skew [Auto] CPU I/O Drive Strenght [Auto] =============================================================== >Memory Tweakers'Paradise IMC AB Signal 1 [Auto] IMC AB Signal 2 [Auto] IMC AB Signal 3 [Auto] IMC CD Signal 1 [Auto] IMC CD Signal 2 [Auto] IMC cD Signal 3 [Auto] DRAM CTRL REF Voltage on CHA [Auto] DRAM DATA REF Voltage on CHA [Auto] DRAM CTRL REF Voltage on CHB [Auto] DRAM DATA REF Voltage on CHB [Auto] DRAM CTRL REF Voltage on CHC [Auto] DRAM DATA REF Voltage on CHC [Auto] DRAM CTRL REF Voltage on CHD [Auto] DRAM DATA REF Voltage on CHD [Auto] DRAM Read REF Voltage on CHA [Auto] DRAM Read REF Voltage on CHB [Auto] DRAM Read REF Voltage on CHC [Auto] DRAM Read REF Voltage on CHD [Auto] =============================================================== >PCH Chipset Tweakers'Paradise PCH 1.5V Voltage 1.503V [Auto] PCH 1.1VG [Auto] PCH DMI Strenght [Auto] PCH DMI Skew [Auto] PCH USB Skew [Auto] PCH SATA3 Strenght [Auto] =============================================================== >VGA Tweakers'Paradise VGA1 Core Voltage [Auto] VGA1 Core Voltage Boost [Disabled] VGA1 Memory Voltage [Auto] VGA1 PLL Voltage [Auto] VGA2 Core Voltage [Auto] VGA2 Core Voltage Boost [Disabled] VGA2 Memory Voltage [Auto] VGA2 PLL Voltage [Auto] =============================================================== ***************************ADVANCED**************************** =============================================================== CPU Configuration Intel Adaptive Thermal Monitor [Enabled] Hyper-threading [Enabled] Active Processor Cores [All] Limit CPUID Maximum [Disabled] Execute Disable Bit [Enabled] Hardware Prefetcher [Enabled] Adjacent Cache Line Prefetcher [Enabled] Intel Virtualization Technology [Enabled] >CPU Power Management Configuration CPU Ratio [Auto] Enhanced Intel SpeedStep Technology [Enabled] Turbo Mode [Enabled] CPU C1E [Enabled] CPU C3 Report [Enabled] CPU C6 Report [Enabled] CPU C7 Report [Enabled] =============================================================== System Agent Configuration Inter(R) VT-d [Disabled] PCIE_X16_1 Link Speed [GEN3] PCIE_X16/X8_3 and PCIE_X8_4 Link Speed [GEN3] PCIE_X8_2A and PCIE_X8_2B Link Speed [GEN3] =============================================================== PCH Configuration High Precision Timer [Disabled] ===============================================================
BTW, those are my 24/7 settings if anyone interested.
...and in picture.
Maximus 5 Gene | i7-3770K @ 5GHz | ADATA 2x2GB @ 2.6GHz 9-12-10-28-1T | HD7970 @ 1200/6400
Rampage 4 Extreme | i7-3930K @ 5GHz ||| X58-A OC Orange | i7-980X @ 4.6GHz
Hello I have a problem
you look at the video
take with you the start and as long
http://www.youtube.com/watch?v=FGsip...=youtube_gdata
Bookmarks