[ WorkLoG ] SilverStone TJ11 W.C. By MR. YAKUZA

[MR. YAKUZA]

* SILVERSTONE TJ 11 W.C. By MR. YAKUZA *

* This project will be updated as we receive the components. *

COMPONENTS OF LIQUID COOLING

* SILVERSTONE TJ11

* AX1200 CORSAIR

* EK Dominator Ram - Plexi / Nickel EN

* HF Aquacomputer kryos Cuplex

* FB EK-EK waterblocks RE3 - Acetal / Nickel

* Bitspower Black Freezer VG-NGTX580 x2

* EK D5 DUAL TOP 2 LOOPS

* Laing D5 Vario 12v (Swiftech MCP655) x2

* Lamptron Touch Sleevings Cables

* BlackIce 240 SR1

* BlackIce 480 SR1

* Nidecs GT 1850 rpm x6

* SilverStone FF101 Grille x6

* EK-EK waterblocks Multioption RES X2 - 250 Advanced

* Additive Red Mayhems

* Transparent Tygon 19/13 x3

* Prolimatech PK-1 x2

* Scythe Bay Adapter 3.5 to 5.25 HDD Rafter

* Velcro-Danger Den D5 ( 3M ) x7

* Carbon Vinyl 3M x2

* Silver KillCoil

* 5-Way AlphaCool Collector HF G1 / 4 Deep Black x2

* Adapter 1 / 4 IG G1 / 4 BLACK MATE Rotable 90º Bitspower

* Bitspower Compression Fitting 19/13mm MATE BLACK x15

* Plug 45 º G1 / 4 Bitspower MATE BLACK x10

* Q Adapter Bitspower MATE BLACK x4

* Adapter 45 º Bitspower MATE BLACK x4

* Plug Bitspower G1 / 4 MATE BLACK x10

* Stand Phobya 4x120mm Radiator

* Stand Phobya 2x120mm Radiator

* BitFenix ​​24-pin ATX Extension Cable 30cm Black

* BitFenix ​​12v 8-pin EPS Extension Cable Black x2

* BitFenix ​​6-pin VGA Extension Cable Black PCI Express x2

* Bitfenix VGA 8-pin PCI Express Extension Cable Black x2

* BitFenix ​​Adapter 3-pin Black 90cm x6

* BitFenix ​​Adapter 3-pin Black 60cm

* BitFenix ​​x4 SATA 20cm Molex Adapter Black

* Nzxt Sata cable 4 in 1 20cm

* ColdZero P-Clip 16mm (Pack 10)

* ColdZero P-Clip 19mm (Pack 10)

* ColdZero P-Clip 3mm (Pack 10)

* ColdZero P-Clip 6mm (Pack 10)

* ColdZero P-Clip 9mm (Pack 10)

POSSIBLE SKETCH

The hardware to use is the same as I have in my signature.

[MR. YAKUZA]

SILVERSTONE TJ11

**UNBOXING**



















**QUALITY ALUMINUM ANODIZED AND POLISHED**

















**AIR PENETRATOR AP181**









**REMOVABLE TRAY PLATE / SCREEN PROTECTOR TOP**

















**CABLES: RESET / ON & RPM CONTROL**











**FOR HARD DRIVE BAYS / C. RADIATORS / C. POWER SUPPLY**









**RIVETS**

[MR. YAKUZA]

[CENTER]

CORSAIR AX1200

EVGA BACKPLATE 580 GTX

[MR. YAKUZA]

CARBON VINYL 3M

*I started to try the 3M Vinyl Carbon on the motherboard tray. I have not covered at all, it would be cover for the Motherboard, so only the small corner!

VARI0US

**Scissors Cut Straight Hose**





**PHOBYA Screws Kit & ARTIC Cleaner**



**White Leds NZXT 2m**



**Screws M4 Allen 40mm & 35mm Black Matte**





My Briefcase!! xD



Velcro-Danger Den D5 ( 3M ), Scythe Bay Adapter 3.5 to 5.25 HDD Rafter, 5-Way AlphaCool Collector HF G1 / 4 Deep Black &
Adapter 1 / 4 IG G1 / 4 BLACK MATE Rotable 90º Bitspower

[MR. YAKUZA]

**MAKING PROCESS**

Sorry for my ENGLISH, I just using the GOOGLE TRANSLATION!!


*Today, as I have the day off, while it is stopped waiting for the order of the WC components, I decided to buy thermal paste Prolimatech PK-1.








*Then I went to a stationery to get me 2 pieces of foam board White & Black (50x70) to make a model of what would become the cover for the bays 5.25, screwed apart is where the tank would go.
Whenever I get the measurements and the desired shape, it would happen to a sheet of aluminum later.






*Start taking measurements, height and width of 5.25 units compartment! Then we had a pencil all steps in the foam board.







*Well, now we have to cut with the cutter, for that I caught my tablecloth rubber mat to avoid scratching the glass on the table.
Once cut, check to see if the measurements are correct.







*Well, it seems I was right with the action! xD
Continue cutting, but this time, without excessive pressure to the cutter, since we do not want to separate the sides. Recheck.









*Regarding cables optical drives, would go through these 2 holes. We can terminate the model. So is the top of the respective deposit aluminum and reservoir.









*Maybe tomorrow or next day, sure I'll receive the package of W.C components, I advance in removing the hard drive bays.
Bolted to the side and below the tower, where are the rubber bands that make the foot of the tower.













*I've also changed the STOCK fan plate by a Corsair fan, which I have there, because at least he has the black wire that matches the cases color.






*Well, heres the aluminum plate that I've bought in Bauhaus ( Big Store like CostCo ). I preferred to be an iron grille finish. xD









*We took measurements of the foam board model and we are going to cut it. With the scissors to cut straight, especially aluminum, the edges are great.







*With a wrap tape bodywork edges to avoid scratching the box, and check in case the measure if it is correct.













*We return to the previous foam model and use it to guide us from the measure of the edges . I use the wrap tape again to mark the bodywork width of the border.













*A week ago, I thought that this moment would be a dilemma. Honestly I'd thought about going tosee a panel beater to cut the aluminum sheet to size, but of course, do not leave that taste in your mouth when you do it yourself.
So ............... nothing of tools, only with the edge of the table! Slowly and with a good hand, supporting my weight with my arms, I have been marking the edges. We check if it fits ............. and











*Mark the hole. I decided to cut half of the 2 edges, leaving only a top and a bottom that is where screwed, so Assure that would not bother no optical drive or the rehobus when placed later.











*Here is the result at the moment.

[ying]

Hi mate!, congratulations for your new build it looks interesting and about the case, this is a beast

[MR. YAKUZA]

Hi mate!, congratulations for your new build it looks interesting and about the case, this is a beast

Hey, Ying nice to see you, bro! xD

[Piti Wei]

Nice assembly and good work with the grid

[LeandroJVarini]

nice work, i following...

[MR. YAKUZA]

From COLDZERO!! Ricardo, thanks for all!!













Thanks also for the gift an SLI CUSTOM COVER ACRYLIC, ! You have given me an idea .......... xD







A little bit of 3M VELCRO.........

[MR. YAKUZA]

MY PACKAGES!!

NIDECS GT 1850rpm.

2 BITSPOWER BLACK FREEZER 580GTX BLACK MATT.

I LOVE IT!!

2 PUMPS LAING D5 ( SWIFTECH MCP655 ).

BITSPOWER FITTINGS BLACK MATT!!

EK DUAL TOP D5.

EK MULTIOPTION X2 RES-250 ADVANCED.

EK-FB R3E.

LAMPTRON TOUCH,

RADIATOR BLACK ICE SR-1 240.

I've been testing the M4 35mm screw black matt with a Nidec and a Silverstone filter.

RADIATOR BLACK ICE SR-1 480.

AQUACOMPUTER HF CUPLEX KRYOS!!

KILL COIL

BITSFENIX.

3m TYGON 19/13

MAYHEMS DYE.

SILVERSTONE FILTERS.

PHOBYA STAND RADIATOR 480 & 240.

TOOL KITS, BITPOWER SLI CONECTOR & PROLIMATECH PK1.

[Piti Wei]

Nice work for now!

[MR. YAKUZA]

I'll Update this a little, little by little due to lack of time!

Here is the KILL COIL, I had to split into 2 because it is huge! I passed the silver spray cleaner.



Advanced 250 reservoir, so more or less left at the end.







I cleaned the block on Saturday, with flour, distilled water and vinegar. Next, the clamping arms, I personalized it with some Vinyl Carbon 3M. To do this, I used cutter type knife that is more accurate.





























Looking leakage components.



Well, I have been dismantling the Silverstone TJ11, and only used the screwdriver. Nothing else. It was so easy. I've been checking the space between the two radiators and power supply.



Here my simple method of draining water, go to the left of the SR-480 Black Ice.

[MR. YAKUZA]

Well I've taken my 2 GTX 580 Pny XLR8 Performance Edition. I'm going to mount Bitspower blocks and backplate . Here's the first one!! I Will use the same Bitspower backplate, the EVGA backplate is out!

[MR. YAKUZA]

I got more stuff! xD

BITSPOWER Q ADAPTORS

For SLI, the 90 º Bitspower adapters that come with the VGA's blocks will be used for radiators.

BITFENIX EXTENSION CABLES 3 PIN 90cm (x 6) & 60cm + x4 SATA CABLE NZXT.

I begin to organize the cables. I used the COLDZERO P-Clips with M4 8mm screws.













Here's the mini cuts that I made for cables.





So for now this project, in the absence of ordering, customizing, finalize the small details ........ I have placed in the tubes not to confuse a divot after the placement of the hoses! xD
Well, I think I on the right way! xD

[easegantini]

Excelente job! I´m impressed. Thanks for taking photos. Nice worklog. I will use some of your ideas for sure. Keep posting!

[Beriphent]

Those Bitspower waterblocks look so yummy.

Nice work so far on the TJ-11! Keep it up.

[MR. YAKUZA]

EK RAM DOMINATOR

With a little bit of 3M VINYL CARBON!! Comes from AQUATUNING!













I've already ordered the cables and I've put more foam in the DUAL TOP! It will remain so, clear of wires to power up / down the revolutions of the pumps without discomfort.





Clamps deposit! I do not like the quality and finishing of plastic EK. I sanded it with a little bit of 3M VINYL CARBON.













The COVER grid and finally painted

[MR. YAKUZA]

Excelente job! I´m impressed. Thanks for taking photos. Nice worklog. I will use some of your ideas for sure. Keep posting!

Those Bitspower waterblocks look so yummy.

Nice work so far on the TJ-11! Keep it up.

Thanks for the encouragement guys!! xD

[ChaosAD]

Looks great, i like it a lot so far. Keep up the good work.

[MR. YAKUZA]

Looks great, i like it a lot so far. Keep up the good work.

Thanks, I'll try it!!

[fr0wn3r]

Nice touch on that wb and reservoir clamps.

[LeandroJVarini]

nice work! perfect! congrats

[MR. YAKUZA]

HOLA!!

My new Bluray Samsung SH-B123L.





Here the difference in length with the Sony BDU-X10S





With a bit of vinyl to blend its light color as the tower once.





Forming gum 5mm. I've had to cut a bit with cuter ,because those 5mm are a bit wide for my taste.

[MR. YAKUZA]

Checking the opacity of the Cover Grid!

NEAR



MEDIUM



FAR