New System Specs
Asus Ramgage IV Black Edition
CoolerMaster Striker Case Black
SeaSonic 1250 XSeries
Intel i7- 4960X (Running 4.5GHz @ 1.375v LLC 25%
Dominator 2133 9-11-11-31 CR1 Running 8 x 4GB / 32GB
3 x Red 2TB Running Raid 5
2 x Samsung Pro 250GB Running Raid 0
2 x Evga 980 Sli
CPU Water Cooling & Video Card Cooling Dual Loops EK
Dell U3415W 34"
that looks awesome, how were you able to keep the 90 degree bends like that?
Gave me a boner
Mayhems dye?
That looks awesome. I love the tubing bends.
How did you manage to pull that off? What tubing did you use?
Love the purple! Quite a few 90s as well.
Love the tubing turns...
System:1
Banchetto
I7 860 4.2Ghz | Asus Maximus III Formula | EVGA 2 GTX295's | 4Gb (2x2Gb) Dominator GT Ram @ 2000 8-9-8-24-1T | OCZ RevoDrive3 120Gb SSD | Barracuda 500Gb HDD
W/C System
Apogee XT | EK-FC285 Nickel| Thermochill PA 120.3 | TFC Xtender Shrouds |DD Monsoon Premium D5 Dual Bay Reservoir | MCP655-B|Noctua NF-P12| HydrX | B*P Compression Fittings
System:2
Sunbeamtech Ultra-Tech Station
I7 875K 4.4Ghz | EVGA P55 LE | PNY Quadro FX4800 | 4Gb (2x2Gb) Dominator Ram @ 1600 8-8-8-24-2T | 2 OCZ Vertex2 60Gb SSD RAID 0 | Barracuda 500Gb HDD
W/C System
Apogee XT | DD Koosah | 2 Thermochill PA 120.1 | TFC Xtender Shrouds | EK-DDC X-RES 100 | MCP350 | Noctua NF-P12 | Indigo Xtreme | HydrX | B*P Compression Fittings
System Videos
+1 how to get such bends. Adds up to looks a lot, without using stupidly expensive "hard tubing" from fittings and crystal link tubes.
Please tell me there's a worklog and detailed explanation for this.
As all the posts above - tubing bends look pro! Did you shape them using the warm water trick?
Zombie Killer Corsair 700D with Quad Rad mod+240 rad mod/Asus Maximus III Formula/i5 750 @ 4Ghz/8GB GSkill Trident/HIS HD 6990/Dell u2711/120GB Kingston SSD Now!/All under EK watercooling goodness!
HTPC Lian Li V354B/i5 750/4GB Corsair/MSI HD5770/60GB GSkill Phoenix/Corsair H50/EVGA P55 Micro SLi
WHoa!
nice bend(s). I didn't expect that to be possible with such large sized tubing.
Any strings? The one from the front rad to graphics card is especially impressive. There's a support on the motherboard isn't there?
To do bends like that (not sure if the OP did it this way) stick some 1/2" rope down the tubing to hold the centre round, spiral wrap some thick gauge wire (thick solder works well) round the outside of the tube leaving a small hook at one end. Bend the tube to the desired shape. Hang it in the oven off a grill tray using the hook you shaped at around 80c (dont pre-heat oven!) for 15 mins, then plunge it straight into a bucket of cold water to set the shape.
May take two goes to get it right with really thick wall tubing. The rope is important to stop the centre collapsing into an oval.
Build looks really sweet .
Tubing bends very nice...
Looks like the new Lian Li 2120?
Absolutely beautiful! Super sexy! Loving the bends and the colours. Very clean looking build! Please post more
PROJECT :: The Xtreme (WET) Dream!!!
PERSONAL H2O BESTS :
E8600 @ 4.8GHz E6750 @ 4GHz QX9650 @ 4.6GHz i7 920 @ 4.6GHz
PERSONAL AIR BESTS :
Sempron140 @ 4Ghz (Stock Cooler) i7 3960x @ 5.4ghz (Air Cooler)
Bex : "Who said girls can't play PC games or overclock!? Do I look like your imagination!?"
Aaron : "TBH, a girl doing all that is a pretty perfect girl!"
Swift_Wraith : "could someone please check bex for a penis?"
insane bends with no kinks! impressive..
Another thing I find funny is AMD/Intel would snipe any of our Moms on a grocery run if it meant good quarterly results, and you are forever whining about what feser did?
New System Specs
Asus Ramgage IV Black Edition
CoolerMaster Striker Case Black
SeaSonic 1250 XSeries
Intel i7- 4960X (Running 4.5GHz @ 1.375v LLC 25%
Dominator 2133 9-11-11-31 CR1 Running 8 x 4GB / 32GB
3 x Red 2TB Running Raid 5
2 x Samsung Pro 250GB Running Raid 0
2 x Evga 980 Sli
CPU Water Cooling & Video Card Cooling Dual Loops EK
Dell U3415W 34"
Bookmarks