pencil or VR across those resistors should give the desired results to increasing OCP limit
pencil or VR across those resistors should give the desired results to increasing OCP limit
It isn't MSI's fault if you want to mod your Card!
Nobody told you that u have to do this! Like all the time with a Hardmod!
So mate blame you and not MSI.
If you have tested your card and you have seen that the OCP isn't the problem (OCP problems cause in Black Screens at high load) why you should mod your card?
Have you done all exaktly after the guide? And what happend then?
Burned? Just no more picture? Have you desoldered the mod and tested again?
There really is so much to benching these things, it's not just a matter of hardware. elmor will probably hit 1700 with his
With our card no problem with the OCP jumper...
Never had any issue with OCP switch on Lightning or Hawk.
Where courage, motivation and ignorance meet, a persistent idiot awakens.
i know it sounds wierd but i guess it my inexpierance with it.
was also sent this pm (which will stay pm in name) from msi guy after i told him about how my second hawk died with just jumper... was late notice then too
msi guy
"We just found out a bug on OCP unlocker, please do not use this function! "
so as you can see thats why i said what i said not just out of the blue or anything..i would have tested it 6 ways from tuesday before it made retail
this card np with switch,was like first drive after big wreck
have not tested mod yet to busy killing my 3rd hawk not switch,was all me on that one.
sry for ot
getting the 580 ready now. i only test without pencil mod first
then
ER1091 from 9.09k to sightly lower resistance
ER1103 and ER1059 from 48.7k to sightly lower resistance
and will gadually get lower if it helps all while i raise core voltage.
Last edited by cowie; 04-13-2011 at 03:07 AM.
_________________
Just tested the mods. Card's still working. No problem.
Where courage, motivation and ignorance meet, a persistent idiot awakens.
- Short ER1091 for OCP per channel
- Short ER1059 for OCP overall
Don't know why they also indicated the third one ... I just shorted these two and both IMAX are now 0 ohm
Where courage, motivation and ignorance meet, a persistent idiot awakens.
Massman this card you are testing at the moment os your second or your third
Super Pi and Tweaking until death....
I was going 1150 -1200 1.34v core ram would not move off 1250 much thuo with 1.73v
Thats with just ovp cb-cbb swiches,but was hitting blue screens so i need to mod for ovp i guess?
Are the core speeds per voltage weak sauce results? it was just getting in the groove but the pci- slot frooze up.
this thing is coolness soooooo easy under cold -126c like it was nothing
The only card i eveR used that was like that out of the box
this card is greatness i dont care if i cant get 1500
Now i know why this card might have tri temp monitoring,the vrm area does not get hot even with 1.35v..maybe last along time like that
i test more later
_________________
i guess i'll try the ovp mod and try again,thanks for the info.
_________________
same as the rest of the ref. 470/570/480/580
about 5.9cm hole center to hole center
==
i tried at 1.19v tonight 1100 ish in 06 tests np
05 @ 1.19v was ok for 1140ish but i had to bring down ram speeds.
ran out of ln2 so i could not test more in 06 with higher clock lower ram
i just think load temps of -90c was not low enuff for my 1.35v testing who knows? i'll have fun fiding out with more testing
_________________
Last edited by boblemagnifique; 04-18-2011 at 06:24 AM.
Bookmarks