Chiller's Hybrid SR-2 (56k death)

[felix_w]

Amazing Work!!!

[Alexandr0s]

Nice job on the custom heatsinks, they really fit the dominators well .

[Chillerzero]

today had some fun to make some more Dominator GT flames for my memory :

[ScottALot]

If those dissipate heat well enough, Corsair might have some interest in them... they look sick!

[Chillerzero]

they are made from pure alu, so yes i think they will transfer the heat good enough.

[DexNfX]

@ Chillerzero - those are some awesome looking flamed heatsinks.

[Chillerzero]

update :

[DexNfX]

Looks good!

[Chillerzero]

thanks

[SnW]

Mate i am seriously in love with you're rig as you know from OC3D

[dMITIj]

keep up the good job, keep it comming man, thats crazy! love it!!

[Chillerzero]

waiting on my snake connectors that i ordered, so i can hook up the 3th pump and fill the loop

[Chillerzero]

small update, got at last the snake connector in, so the 3th pump can be fitted and the loop closed,
ready to fill it up.

left of the pump you see all kind of cables , that's for the Koolanc TMS-200 controller, all kinds of temp sensors all around the mobo and cpu's.

[Chillerzero]

i'm going to fill up the loop now the 3th pump is installed, own mixture : 25% Ethylene Glycol and 75% PURE water, no demi.

what you see in the measure cup is the Glycol no color pure 100% glycol :



here my koolanc poor in cup on the ZERN res with a snake connector to make it a little bit eassier to fill :



on the drain valve i putted also a tube in a bus filled with my mixture, where the pump can draw it's liquid from when i put the valve open, to make it a little bit eassier to lol :





and here comes the first liquid lol, pumps are now running to get the last micro bubbles out the loop, for now, no leaks found :

[Chillerzero]

http://www.youtube.com/watch?v=vWzQnCi-d-I

[Chillerzero]

It's a miracle !!!!

i get it closed hahahahaha, +200m cable in limited room of 3,5cm lol :



here you see that the plate is a little round, but i put the cable fast fast in to look if i get it closed,
later on the cable will be nice routed and strapped so that the plate doesn't look round :

[Chillerzero]

last minute adjustment for the vga's :

[Ultimatum01]

Nice build man, looking forward to seeing the finished thing. Nice SIG too ahaha. I was the guy who painted the EVGA wallpaper of the "joker/scientist" with his LN2. Its nice to see people using it.

[Chillerzero]

little update :

[Chillerzero]

http://valid.canardpc.com/show_oc.php?id=1717611

Mobo and cpu's cooled by the two coolers in screenshot software:

[fatherTime27]

nice stuff

[Chillerzero]

thanks

[Chillerzero]

here are the load temps, cpu temp in Coolit software is not correct, cpu isn't supported by the coolit software.

As you see idle the coolers run lower power, when stressed the coolers will raise there cooling power, and keep the liquid temp low, under Ambient,
cpu temp raises a 5 a 6°C from idle to load thanks to temp controlled coolers.

Temp of liquid is set @ 22°C max, min power of coolers @ 60%, max power @ 100%, real nice settings on these coolers,
and the coolers don't even run at 100% to keep the temp, for me that's good for lower noise level :

[billdavis]

There are no words for what you have man

[Chillerzero]

little sneakpeak what i'm doing now :

Most of the time, people put there powercable for vga like the RED arrows.
I whant it as clean as possible in this case, en i will do my powercables like the GREEN arrow, straight horizontal with the vga's.
Vga's seems like they are floating in the air lol, strange sight.

On later time i can mod also the plastic cap on the vga, make it wider, little bit bigger, so the powercables are IN the plastic cap of the vga cooler, totally NOT visible.



And this is the beginning of this little vga mod :