The T.E.C. gallery

[Reflex1]

woaa dats a big motha rad.
ur temps/OC?

[mi_july]

Air cooled pelt,

[mi_july]

the coldplate and peltier (226watt)

[sk8]

Omg, pelt cooling with a thermalright! Hows the temps doing....

[sandman]

how did you attach that pelt?

[mi_july]

the temps r ambient (27c) at idle but thats cause of my very! very! very! poor case airflow in an open air enviroment its all better but atm theres no where for the heat to go and its epoxyed with artic ceramique or sumthing like that.

[kommando]

Get a 120mm fan on the side of the case which is directly in line with the fan on the cpu heatsink and make a air duct

[Reflex1]

My 9800 pro with me 80w pelt MCW50-T ...and my home-made aluminium back plate (painted silver).

more pix can be found here (as well as info like temps etc...):

http://www.xtremesystems.org/showthr...threadid=32185

[Jabo]

Piece of advice a5h m8.
Cove edges of your insulation with dielectric grease so to prevent any air getting in and if you can unse back plate big enough to cover the whole of insulating patch giving it uniform clamping pressure across
Want to see what happens if you do not do it /

[Reflex1]

haha, no thx i've already seen what happens if i dont in the other thread I'll take that adive and shove in some more Di-elec grease on the sides ...will be a while before i can make another clamp tho since i ain't got the time atm. (took like 3 hours to make this one, since it took 2 tries )

[Jabo]

d00d, tell me about it! The whole thing akes up so much time if want to do it right that sometimes mods are no goers (no point in starting a mod if know you not gonna have nuff time to do it is there?)

[kayl]

ok finally got the chiller up and added it to the maze4-1 226w TEc system. running chiller at -20deg
at stock speed im getting -28idle and at current everyday overclock of 11x200 for xp3200 1.75v and -18 deg idle

[kayl]

the actual chiller itself doesnt look that crash hot, need to make a case or box to put the thing in to hide it.

[kommando]

antifreeze it

[boshi]

Originally posted by mi_july
the coldplate and peltier (226watt)

so, how does that work out?

I have a very similar setup I would like to try, and some info would be very helpful.

[=[PULSAR]=]

Nice temps Kayl...for a second you got me all excited I thought those were your regular TEC temps with just water. Whats your coolant temp now?

[kayl]

not running chillier anymore.
best temp was -26c
i would get it to this temp and then shut it off
would last 4-5hrs before reach room temp again
but the damb thing got a leak on the gpu block and killed motherboard and graphics card

why isnt this sticky anymore?

[PanaBob]

Heres a few

[PanaBob]

And another. I'm getting 3-10c idle depending on ambient temp and 15-25c load at 2.65ghz 1.8v 2500+ M

[MeltedDuron]

droooooooooooooooooooooooooooooooooooooooooooooooo oooooll d00d how much that block set ya back? total pwn@ge i want 1!

[saaya]

damn!

nice gabbax!

[vengance_01]

reserved when I get my Swifty 80 watt pelt on my X800XT PE

[boshi]

the swiftech 80 isnt going to cool an x800 very well, it barely got my 9800xt down to 40C with a really good w/c system.

[Aphex_Tom_9]

the swiftech 80 isnt going to cool an x800 very well, it barely got my 9800xt down to 40C with a really good w/c system.

the x800 does have a lower thermal output than the 9800xt...

[caLume]

just played around a bit with a tec, but i think my liquidcoolingsetup hasnt enaugh power for it.

just tested it outside at a swiftech