The 1055T makes it a little more interesting.

[theoldtimer]

I tested the 1055T in the MSI 790FX-GD70 today and the MSI didn’t seem to mind the high HTT. It would boot @381HTT then I could use the OC dial to increase the HTT to 403 in Windows.

I also tried the step overclock feature in the bios . I use step 1 in which it boots @90% of the HTT 381 in this case then the system clocks up to 100% after Windows is loaded (401HTT). That feature works pretty good.

Air cooling


Clocked the NB a little more in this one

[Daveburt714]

Thats pretty nice on the MSI GD70 board OT...

How are temps on the PWM section, did ya do the finger test?

I'm assuming thats your cold water settup.

[FlanK3r]

whau, look good this board! Try max stable clock with air

[theoldtimer]

Thats pretty nice on the MSI GD70 board OT...

How are temps on the PWM section, did ya do the finger test?

I'm assuming thats your cold water settup.

Thanks Dave, using air for those tests. I don't know what the PWM temps were? I'm not really pushing it yet maybe I will today?

whau, look good this board! Try max stable clock with air

Thanks FLanK3r, I may test that before I put it under the chiller today?

[FlanK3r]

:-)

[CoNtAcT]

Hey, my 1055->@ 1,216V!!
Here a picture:

[theoldtimer]

Nice low volt stability run What is the default vcore for that chip?

[pcnazz]

Nice low volt stability run What is the default vcore for that chip?

Yep , looks like that chip may oc very well . What's your 1055 stock core freq for v oldtimer ? What wattage chips you guys have ?

[theoldtimer]

Yep , looks like that chip may oc very well . What's your 1055 stock core freq for v oldtimer ? What wattage chips you guys have ?

All my Thubans are 125w and if I remember correctly the 1055T defaults to 1.36v. I'll check it the next time I bench it, if I remember.

[FlanK3r]

how about 1090T default vcore? Think, my is 1.28V in default....

[theoldtimer]

how about 1090T default vcore? Think, my is 1.28V in default....

My 1090T (week 21) is 1.283v default in bios.

[FlanK3r]

yes, this is simillary

[deNordic]

Could anyone with Phenom II X6 @ 4Ghz and 5970 (stock , with 10.9a ccc) post a Vantage - Perfomance?
Need to see if it can brake the 26k gpu points wall.

Thanks

[theoldtimer]

Could anyone with Phenom II X6 @ 4Ghz and 5970 (stock , with 10.9a ccc) post a Vantage - Perfomance?
Need to see if it can brake the 26k gpu points wall.

Thanks

I understand from reading your post that you were asking about Vantage tests @4GHz on a Thuban using a 5970 at default clocks with CAT 10.9? My 5970 won’t do 26K Vantage GPU scores @ default clocks. It doesn’t take a lot of over clocking on the GFX card to top 26K though.

For all I know maybe some of these other guys have a combination that will top 26K GFX score in Vantage?

Below are three tests from today.
Everything is air cooled but it’s not inside a case.

5970 @ default clocks 725/1000MHz


5970 @778/1103MHz


5970 @906/1203MHz

[CoNtAcT]

Nice low volt stability run What is the default vcore for that chip?

My 1055t is a 125W TDP, but he start @default with 1,288V

[deNordic]

Thank you theoldtimer,
would like to validate this http://www.thelab.gr/1062900775-post17.html
Not sure if it's legit or not.

[theoldtimer]

Thank you theoldtimer,
would like to validate this http://www.thelab.gr/1062900775-post17.html
Not sure if it's legit or not.

You're welcome.

I'm not sure I completely understand. Is this your Vantage test result or someone else’s? Is it important that the 5970 was at the default clocks of 725/1000MHz during the test for the result to be called legitimate?

[deNordic]

You're welcome.

I'm not sure I completely understand. Is this your Vantage test result or someone else’s? Is it important that the 5970 was at the default clocks of 725/1000MHz during the test for the result to be called legitimate?

It's someone's else.
Ofc, i doubt it was at the default clocks during the test.

[theoldtimer]

It's someone's else.
Ofc, i doubt it was at the default clocks during the test.

Ok I understand now.