tried this before. I have tried many different combinations. I am up for suggestions.
I am hoping for some help for you guys. This might be off slightly because I am doing this from work. I have gotten as high as 4.44GHz with turbo on. I am shooting for a benchable 4.5GHz+, not 24/7 specs. If you guys can help out it would be greatly appreciated. Thx in advance.
CPU & Batch: i7-920 D0 3910A307
RAM Model: Corsair Dominator GT 1600MHz 6GB
Bios Ver: Quantum BIOS P09
CPU Features
PPM ...............................: Enabled
EIST ..............................: Enabled
CxE................................: Disabled
Execute Disable Bit ...............: Disabled
Virtualization.....................: Disabled
Hyper Threading ...................: Enable
Active Processor Cores ............: All
CPU QPI Latency ..............: Auto (i have tried 100)
IOH QPI Latency ...............: Auto
CPU QPI Drive Strength .......: Auto
IOH QPI Drive Strength .......: Auto
Memory Settings
Memory Controller Settings
IMC Configuration .................: Enabled
Channel Congifuration .............: Independent
Channel Interleaving ..............: 6 way
Rank Interleaving .................: 4 way
Memory Timings
Extreme Memory Profile XMP ........: Disabled
Memory Profile Select .............:
DRAM Timing Control ...............: Manual
tCL (CAS Latency) .................: 7T
tRCG (RAS to CAS Delay) ...........: 8T
tRP (RAS Precharge) ...............: 7T
tRAS (Precharge Delay) ............: 20T
CR (Command Rate) .................: 1T
tRFC (Refresh Cycle Time) .........: 62T
tWR (Write Recovery Time) .........: 6T
tWTR (Write to Read Delay) ........: 14T
tRRD (RAS to RAS Delay) ...........: 3T
tRTP (Read to Precharge) ..........: 3T
All Voltage Settings
CPU Voltages
CPU Core Voltage ..................: +270mV (not sure but in the neighborhood)
CPU Target Core Voltage ...........: 1.4875V (VID =1.23)
CPU Vdroop Compensation ...........: disabled
CPU VTT (UnCore) Voltage ..........: +300mV
1.8 PPL Voltage Setting ...........: 1.890V
CPU Clock Amplitude Ctrl ..........: 0.900V
Memory Voltages
DRAM Voltage ......................: 1.65V
DIMM1 Vref CA (Addresses) .........: x 0.500
DIMM1 Vref DQ (Data) ..............: x 0.500
DIMM2 Vref CA (Addresses) .........: x 0.500
DIMM2 Vref DQ (Data) ..............: x 0.500
DIMM3 Vref CA (Addresses) .........: x 0.500
DIMM3 Vref DQ (Data) ..............: x 0.500
Chipset Voltages
X58 IOH Core Voltage .............: 1.22V
X58 IOH VCCA 1.1V ................: 1.116V
X58 IOH VCCA 1.5V ................: 1.506V
ICH10 SB Voltage .................: 1.530V
OC Gear : Skipping this part
CPU Turbo .........................: Always On
System Turbo ......................: Enabled
Clock Speed Control Center
CPU Bclock (FSB) ................: 211MHz
QPI Link Fast Mode ..............: Enabled
QPI Multiplier ..................: x18
QPI Target Speed ................: 3798MHz (7.2GT/s)
CPU Core Multiplier .............: x20 (21)
CPU Core Target Speed ...........: 4226MHz (4436MHz)
CPU Uncore Multiplier ...........: x16
CPU Uncore Target Speed .........: 3388MHz
Memory Bus Multiplier ...........: x8
Memory Bus Target Speed .........: 1694MHZ
PCI Express Bus Clock............: 100MHz
I have tried 103MHz on pci-e bus and changing CPU QPI Latency to 100 but no boot up past 215 bclk. 214 boot at 1.56v but usb items start flickering. Keep in mind, I am not looking for stable settings just enough to run 3DMark Vatage and 06. Thx.
Bookmarks