*King of the hill* A-Data XPC Plus DDR3 2200 CL8 v2.0 take a walk to DDR3 2680 CL8

[CryptiK]

Thanks, I just drove over 9 hours back home and my brain is not working, thankfully yours is!

[liberato87]

NICE!!!
I'll try with your settings to see if it is a mainboard problem .


Actually I'm "only" 1866 7-7-7-21 1T @ 1,575v memtest stable




and linx stable

[badatgames18]

Thanks, I just drove over 9 hours back home and my brain is not working, thankfully yours is!

yap sorry cryptik..

i had imageshack not resize so it was original resolution, but for some reason it still looked tiny on XS

same mem.. no os tweak.. just xp straight from install.. it is 1t, can't fit everything due to small screen resolution... it won't let me change it in xp
also 32m coming up... tomorrow

[CryptiK]

Nice one!

XP res - should let you change it like normal? Not sure what it could be.

[badatgames18]

Nice one!

XP res - should let you change it like normal? Not sure what it could be.

normally you just go to properties, and change the res by sliding the little slider to the res you want, but in my case the stupid resolution slider doesn't want to slide

i can't fit a third cpuz on screen.. so alot of my benches will be useless

maybe it's just the vid card.. i'm using it right now on win7 @ 1080p so i don't know what's up.. gonna switch to my 570

[badatgames18]

fix the screen


brain was not working

[Morphling]

fix the screen


brain was not working

Nice results there But from What I see you are having the same issues as me With 2133 multiplier on SB it is very dificult to do SPi 32M. I've done this, but I can't use waza because if I do, after one or two loops the pc just freezes

I have Corsair Dominator GT 2000mhz 8-8-8-24 Elpida Hyper MGH-E IC's - rare kit

Without waza


SB and Elpida MGH-E are two guys that when they are together, many things can happen, good things and bad things :P

[kagula323]

Nice results there But from What I see you are having the same issues as me With 2133 multiplier on SB it is very dificult to do SPi 32M. I've done this, but I can't use waza because if I do, after one or two loops the pc just freezes

I have Corsair Dominator GT 2000mhz 8-8-8-24 Elpida Hyper MGH-E IC's - rare kit

Without waza


SB and Elpida MGH-E are two guys that when they are together, many things can happen, good things and bad things :P

what voltage did u use on the ram?

[Morphling]

what voltage did u use on the ram?

For that it's just not about voltage :P Depending on your IC's you can have it doing this with 1.85v, or you can have it doing with 1.75v, but I've used 1.825v. The problem is that I can to further to higher mhz with that voltage, but Sandy Bridge is very booring Above 2200mhz on SPi 32M with Hypers is almost impossible! No matter what voltage you use.

You can see here:



As you see, I can do lots of mhz on almost everything, but on SPi 32M is just a headashe

[badatgames18]

For that it's just not about voltage :P Depending on your IC's you can have it doing this with 1.85v, or you can have it doing with 1.75v, but I've used 1.825v. The problem is that I can to further to higher mhz with that voltage, but Sandy Bridge is very booring Above 2200mhz on SPi 32M with Hypers is almost impossible! No matter what voltage you use.

You can see here:



As you see, I can do lots of mhz on almost everything, but on SPi 32M is just a headashe

hi morphling.. very nice memory clock for super pi 32m! 1100 on these kit is big pain also, with 7-7-6 timing
you are right, on that run i didn't do waza
not because i was freezing though,(cdt for waza takes forever on my computer was just impatient) if you apply enough vdimm it will stop the freezing problem.. also play with blck skew

i am going to guess that your kit will need 1.83-1.85v for it to go through iterations without freeze

good luck

[Morphling]

hi morphling.. very nice memory clock for super pi 32m! 1100 on these kit is big pain also, with 7-7-6 timing
you are right, on that run i didn't do waza
not because i was freezing though,(cdt for waza takes forever on my computer was just impatient) if you apply enough vdimm it will stop the freezing problem.. also play with blck skew

i am going to guess that your kit will need 1.83-1.85v for it to go through iterations without freeze

good luck

Thanks for the tips badatgames18 I'll try it soon But I think vdimm will not stop the freezes I've even gave 1.95v... But bclk skew I didn't try yet I'll do that!

Regards!

[liberato87]

We have a for sale forum.

Sales are forbidden outside that subforum.

sorry for going off topic

[Devil_Dog]

I've a pair of kit of this fantastic adata 2200 xpg+ v 2.0 2200 cl8 (1 is new, boxed) for sell.
where is the sale forum?

I can see there is a section but there are few threads and many of them are about deals of professional vendors.. could you link me the right section?

You don't have enough post to enter it.