DFI P45 696MHz FSB

[LAMB OF GOD]

DFI LP UT P45-T2RS with CoolerMaster V10 on cpu , stock mb cooling with added fans 90CFMs~


http://valid.canardpc.com/show_oc.php?id=700588


http://valid.canardpc.com/show_oc.php?id=700606


http://valid.canardpc.com/show_oc.php?id=701828

RU DOING IT ON AIR????
wow ...
so ur cooling ur chipset with just 90mm fans ... put some ln2 or DICE on it ... hope to see dfi getting back fsb wr from gigabyte

[Oliver]

Was for the comparison

the DK P45s are flying FSB wise,

I personally havent seen any LP UT board, touching or getting near what the DK does in terms of FSB overclockability.

RU DOING IT ON AIR????
wow ...
so ur cooling ur chipset with just 90mm fans ... put some ln2 or DICE on it ... hope to see dfi getting back fsb wr from gigabyte

yes all air:

stock motherboard cooling, supplied with 92 and 120mm fans with about 90CFM~ each.

[Mafio]

http://valid.canardpc.com/show_oc.php?id=435227

a friend of mine made this with cpu and nb on air

[knopflerbruce]

Nice scores, Massman. it's a shame the UT's aren't as good as the DK series. I'm using an UT P45 here right now (24/7 rig), awesome board - but hates high FSB.

[Turrican]

nice pieter-jan.
the vpll is a bit high tough

[Oliver]

Nice scores, Massman. it's a shame the UT's aren't as good as the DK series. I'm using an UT P45 here right now (24/7 rig), awesome board - but hates high FSB.

Hey Knopfler, thanks for reporting in

memory OC wise its cool, but its quite conservative regarding FSB compared to the DK as you say yourself.

[OC4/3]

Very very good FSB massman but i believe 700FSB is doable

[blind_ripper]

i hope MM can get the dfi back to life so he can try the E8400.
we benched some I7 with GTX260 today

here's a little movie.
http://www.youtube.com/watch?v=hyRiO3tL3R4

[kamieldehond]

you can do it! and i think the UT is a lesser board. anyway mine is

[Hampti]

Sorry Oliver. I haven't seen that you have a UT and not a DK. So your FSB is impressive. My big fault.

[Oliver]

Sorry Oliver. I haven't seen that you have a UT and not a DK. So your FSB is impressive. My big fault.

hey Hampti dont say sorry

Thanks for the kind words, but as written its far from impressive compared to DK or some Rampage Extremes

keep pushing it

[Leeghoofd]

Put up a biker babe on the white board, that will motivate even more ( also us the readers :p) 1.95Pll poor cpu..; I hope the mobo will revive...

[95blackz26]

i dont have a DK but i have a UT p45 t2rs and anything over 500 and im having a hard time keeping the voltage low.

Oliver how did you get 600+fsb on 1.29 vcore. little more insight as to what voltages your running elsewhere and what GTL's

[saaya]

mass, if you cant boot with cas6 check a different spd... some boards refuse a certain cas if its not in the spd.
dont think its the case here but its worth a try... but in my experience cas6 doesnt help to get higher mhz vs cas5... at least on the ddr2 chips i tried (micron gmh/gkx+elpida+powerchip)

[Oliver]

i dont have a DK but i have a UT p45 t2rs and anything over 500 and im having a hard time keeping the voltage low.

Oliver how did you get 600+fsb on 1.29 vcore. little more insight as to what voltages your running elsewhere and what GTL's

I will post full setting details, once i get back to the setup once again

[angoholic]

the BI Elite and the DK+ can reach same results..If i have time, i will give it another try to go past 740..

[kamieldehond]

I will post full setting details, once i get back to the setup once again

would love to see them. I had not much trouble booting at close to 600 fsb on my UT but everything above 500 fsb is impossble to get stable

[aslanwas]

the BI Elite and the DK+ can reach same results..If i have time, i will give it another try to go past 740..

Boaaah , very nice, NB on LN2 , dice ? keeep pushing

[Oliver]

would love to see them. I had not much trouble booting at close to 600 fsb on my UT but everything above 500 fsb is impossble to get stable

Please note, that the CPU-Z screen 640 FSB is not stabl e(bench or 24/7 wise)

However i will post the settings and then we can see if they can be to any help or point you in the right direction

Peace

[WaterFlex]

740 FSB bwaaaaa 0_0

[angoholic]

lol this is not my thread..

massman: did you also have troubles with that board and C1 errors making it harder to handle?

[95blackz26]

I will post full setting details, once i get back to the setup once again

ok cool. just curious on what others are running on air or water with high fsb on this board.

[westsider]

Pieter most modules need more then 2.7V to break 700MHz
i have too much time spent with ddr2 micron modules and not every of them are capable of 700+
i would recommend you to buy 650er Teamgroup 6-6-6-18
they are either handpicked GMH or GKX and do as minimum of 750 under 2.7V for sure
or some old ballistix with GMH GKX
if you catch old OCZ reaper or flex 9200 they go fast near 800 under 3V
i think its memory issue
and did you use for 1:1 333 or 400 strap?
trd=?

[Benny Lodewijk]

Good start massman keep pushing them

[massman]

Massman: did you also have troubles with that board and C1 errors making it harder to handle?

Oops, just saw this question.

Yes and no. When the board locks in C1, just turn down the power supply, wait for the leds to turn off, clear cmos, give it a couple of seconds, turn on the psu again and reboot. Worked flawless here.

Luckily, DFI has the bios saving feature