Can I remove the Northbridge waterblock and replace it with a 3rd party cooler.
How do I remove it?
Can I remove the Northbridge waterblock and replace it with a 3rd party cooler.
How do I remove it?
here is the guide
http://www.xtremesystems.org/forums/...d.php?t=213753
and make sure to not damage the tape on the pwn sink u need to reuse it (it just pulls off but dont remove it or let it get dusty)
5930k, R5E, samsung 8GBx4 d-die, vega 56, wd gold 8TB, wd 4TB red, 2TB raid1 wd blue 5400
samsung 840 evo 500GB, HP EX 1TB NVME , CM690II, swiftech h220, corsair 750hxi
thanks zanzabar
Awesome. Thanks zanzabar.
Follow-up Question, using the same method, after removing the waterblock, would I be able to use a Thermalright HR-05 SLI-IFX on it, on top of the heatpipe assembly?
Last edited by 4PLaY; 06-28-2009 at 09:37 PM.
yes, u can use whatever and u can even put the stock cooler back on its a 50mm hole space i think so it should work with most universal systems
5930k, R5E, samsung 8GBx4 d-die, vega 56, wd gold 8TB, wd 4TB red, 2TB raid1 wd blue 5400
samsung 840 evo 500GB, HP EX 1TB NVME , CM690II, swiftech h220, corsair 750hxi
That clears it up, thanks alot.
BTW, just making sure, do I actually place the HR-05 SLI on top of the heatpipes or remove the entire heatpipe and place it directly on top of the X48 Chip?
is it possible to just mount it on top of all the heatpipes? So I dont need other PWM sinks.
u put the cooler on top of the heat pipe
5930k, R5E, samsung 8GBx4 d-die, vega 56, wd gold 8TB, wd 4TB red, 2TB raid1 wd blue 5400
samsung 840 evo 500GB, HP EX 1TB NVME , CM690II, swiftech h220, corsair 750hxi
the mosfet has blue thermal tape u need to have it there or u might crush the pwms and it wont mount with even contact without it
and look at the guide pic, the water block is sitting on top
5930k, R5E, samsung 8GBx4 d-die, vega 56, wd gold 8TB, wd 4TB red, 2TB raid1 wd blue 5400
samsung 840 evo 500GB, HP EX 1TB NVME , CM690II, swiftech h220, corsair 750hxi
Cmon Blizzie make some time! LoL... I wanna see. Go Guinea Pig.. I have my brand new blackops gathering dust here in the corner coz I still dont have the rest of the parts for my new PC.
oh and please dont forget your pics, here are some of my concerns:
1. with the single bar mounting mechanism of the HR-05 IFX-SLI im afraid it wont fit the mounting holes in the BoPs.
2. im thinking the pipes would point towards the Vcard area, 1st PCI-E slot, would there be enough room, maybe even for a thin 80mm fan.
You're the hope of the nation bliz!
u could make a custom mount, and i have no idea what will fit there i used an mcw30 and only and mcw30
5930k, R5E, samsung 8GBx4 d-die, vega 56, wd gold 8TB, wd 4TB red, 2TB raid1 wd blue 5400
samsung 840 evo 500GB, HP EX 1TB NVME , CM690II, swiftech h220, corsair 750hxi
I was thinking about it.. then I figured, a custom mounting system would be needed. I don't recall any holes for the HR-05 to mount properly. (I could be wrong).
I think.. it would still fit, because it's a universal system.
Bookmarks