I have my system running stably at 4.475 MHz. (23 x 195) (LinX 100 runs withVcore at 1.38 volts and Max core temperatures at 74°C).
My memory timings are 7-8-7-20 and I have 6 GB Corsair dominator DDR3 ratings for speed of 1866 MHz presently running at 1945 MHz. Even with all tests LinX, memtest and prime showing no issues, am I risking my memory at these speeds and timing settings?
Appreciate any input.
do u think anybody here can convince sham
to have a ioh skew??
Last edited by cstkl1; 05-20-2010 at 09:38 PM.
Guys quick question. Why does the EVGA E760 I/O shield plate come with some of the holes covered/plated? Do you just fold them back and forth until they snap off? I don't get why some of the holes are covered??
I thought that the flaps were for grounding purposes? I always bent my back far enough so that they contact the IO terminals to ground them against the case.
hey guys just got my 2nd 5870 and want to make sure im getting it right. I should put them in the first pci-e slot and the third slot correct?(the one after the PCI slot).
Also can anyone point me in the direction of a crossfire bridge that will be long enough? the one that came with the card is too short for this configuration.
according to some of the forums they say 100mm or 10cm (asus and msi and xfx) seem to make them
http://www.lotes.cc/product_info.php?id=3046
There is the info for the one that I have.
that is longer than the one i have, mine is currently 60mm, does anyone know if 88mm is far enough to go from slot 1 to slot 3 for xfire?
From holding it up next to mine it looks like it will work. It came with a DFI mobo. I had Crossfire setup on it. Only choice I see for a 100mm is ebay.
I hate to give up so early, but I can't get past 144 BCLK on stock voltages, and after perusing this thread I am at a loss for what voltages to tweak...
e760 gskill trident 2000mhz cl9. Mem div at 2:10 so it's only at 720... err, 1440... using the xmp profile. turbo mode off. HT on.
for anyone who knows what they're doing and forgot what stock voltages are,
And mem (no bios template right now sorry. I know I need that):
So yeah, haven't been able to put any effort into this for almost a year; I try to keep up on this thread but I didn't bookmark the relevant posts. Thanks for reading.
what is yours temps of chipset ? stock cooler
--------------------------------------------------
Intel core i7 980x
6GB mushkim
ASUS Rampage 3 Extreme
EVGA GTX 580 SLi
LG L246WP Widescreen
Auzen X-Fi HomeTheater HD
Corsair HX1000w
WD Velociraptor 600GB Raid 0 l WD 1TB Black l Intel X25-M 80GB G2
Silverstone TJ07
---------------------------------------------------
OCGuate!
so ure prb is getting 2k c9??
whats ure vcore for 4.2ghz
whats ure vtt for 1600mhz
then can tell u whats ure vtt
if its 0mv for 1600 then its around +150-200
if its 25mv then its around 225mv
etc etc
vcore stick to rounded numbers aka 1.2v, 1.25v,1.3v,1.35v for now
for 2k c9
the rtl's should be 62,64,66
mch strap 1600
pwm frequency is where a lot of ppl run issue with
not all their boards can run low pwm frequency
but typically should be good at stock up to 2090
if 200 bclk is hard
then ure proc is a dud dude.
this is what i faced testing 10-15 co/do's
Hi, i just got my 980x possessor and would like to share my first oc with you guys, my target is 4.5 ~4.7mhz.
can you guys take a quick look and tell me if im doing something wrong ?
Frequency Control
CPU Clock Ratio (30x)
CPU Host Frequency (Mhz) (134)
MCH Strap (auto)
CPU Uncore Frequency (Mhz) 4030(134/28x)
CPU Clock Skew (disabled)
Spread Spectrum (disabled)
PCIE Frequency (Mhz) (100)
Memory Feature
Memory Speed (Standard)
Memory Control Setting (Enabled)
Memory Frequency (1867MHz/2:14)
Channel Interleave Setting (6 way)
Rank Interleave Setting (4 way)
Memory Low Gap (auto)
tCL Setting (7)
tRCD Setting (8)
tRP Setting (7)
tRAS Setting (20)
tRFC Setting (98)
Command Rate (1T)
Voltage Control
EVGA VDroop Control (Without Vdroop)
CPUVCore (1.20625)
CPU VTT Voltage (+100)
CPU PLL VCore (auto)
**IOH PLL VCore (auto)
DIMM Voltage (1.61) Bios monitoring reports 1.65
DIMM DQ Vref (+0mV)
QPI PLL VCore (auto)
IOH VCore (auto)
IOH/ICH I/O Voltage (auto)
**VTT PWM Frequency (610 KHz)
**CPU PWM Frequency (1333 KHz)
**CPU Impedance (less)
**QPI Signal Compensation (less)
ICH VCore (1.100)
*PWM Frequency ( )
CPU Feature
Intel SpeedStep (Disabled)
Turbo Mode Function (Enabled)
CxE Function (Enabled)
Execute Disable Bit (Disabled)
Virtualization Technology (Disabled)
Intel HT Technology (Enabled)
Active Processor Cores (All )
QPI Control Settings (Enabled)
QPI Link Fast Mode (Enabled)
QPI Frequency Selection (auto)
OC Recovery (Disabled)
Turbo Performance (Disabled)
10 loops Linx max problem and memory stable
Bookmarks