UnOfficial EVGA X58 Classified Owners Thread

[Wezly]

Yes, set memory at 1.61 if you want 1.65

Seriously? I only peek at this thread from time to time because I haven't been able to tweak my board settings.

Is this for all boards and all BIOS versions?

Sorry to repeat the question...

[ChaosAD]

I would like to know if CPU and VTT PWM frequency make any difference at all in overclocking. The only diffence i got was 3-4 C more on my PWM and 1-2 C more on Cpu when i changed from default to max values. Otherwise the vtt volt and vcore was exactly the same to pass linx. Any info on this?

[Hardass]

Have a question, just picked up the 759. Can I run 2x 295 in SLI using the 1st and 3rd slots?

[Fitseries3]

Have a question, just picked up the 759. Can I run 2x 295 in SLI using the 1st and 3rd slots?

yes. i did this until recently when i sold my 295s. works great.

[Hardass]

yes. i did this until recently when i sold my 295s. works great.

Thats Great, Thanks for reply.

[Hardass]

2nd 295 arrived I installed in 3rd slot, attached sli cable and started rig. It gets to desktop runs for a minute or so gives 4 quick beeps and shutsdown and restarts. Put card in second slot and same thing. Took out my card installed 2nd card in First slot and 4 beeps and shutdown. Put my card back in and system runs fine .

[SAE]

2nd card or psu to consider faulty.

Does your first card work in slot 2/3?

[Hardass]

2nd card or psu to consider faulty.

Does your first card work in slot 2/3?

Amend post, my card in first slot just did same thing. Reinstalled drivers, and switched to Monitor HDMI is running to and 4 beeps and shutdown. It starts goes to desktop and 1 min later it restarts without beeps.

[lowfat]

Will increasing the PCIe bus speed have an affect on PCI cards? I can swap my soundcard over to a PCI one if needed.

[SAE]

Okay, I assume beeps are coming from your classified.

According to the following website it's a RAM?! error...
http://en.kioskea.net/contents/pc/bios.php3

Did you already try slots 2-4 in combination w/out slot 1? It's weird problem indeed... if PSU-related, try to use other pcie connectors (maybe from another rail).

Will increasing the PCIe bus speed have an affect on PCI cards? I can swap my soundcard over to a PCI one if needed.

Some people say, it could hurt your vid cards, but I cannot imagine it does. It has an effect on NIC, USB and some other on- or offboard devices (such as raid cards). Be careful an do some stresstesting. You WILL notice, if some of the devices die.

[Hardass]

Looks like a XP 64 problem. I installed Win7 64 and Running both cards in slots 1-3 with SLI enabled no problem so far.

[MiKA7]

Looks like a XP 64 problem. I installed Win7 64 and Running both cards in slots 1-3 with SLI enabled no problem so far.

afaik you can only use quad sli with 295's in combo with vista or 7..

[Viss]

True, more then 2 gpu cores = vista/win7 only.

[Hardass]

Thanks guys. Do you know if there is a way to use the HDMI output in SLI config?

[SAE]

lol... problem solved. Weird acting of winxp 64 though. I thought it would just deny to support more than 2 gpus, but work nevertheless...

[kpablo]

Hmm... i just measured again to make sure about DIMM Voltage...

In Eleet say 1.67v, i have it set in BIOS 1.65v, and measuring with voltimeter gives me 1.634v. All in IDLE.
Under load, ELEET show 1.66v and with voltimeter 1.62v.

I have an X58 Classified E759.

[[200]]

Will increasing the PCIe bus speed have an affect on PCI cards? I can swap my soundcard over to a PCI one if needed.

Some chips are better clockers than others.

[lowfat]

Some chips are better clockers than others.

My chip is capable of 250+ bclk and has been benched @ 5.2GHz. I just don't have a system capable of it yet

[Dahaka]

Forget the voltage, i'm really drunk last night jajajajaj.

PD: i can't pass 223 bclk stable for superpi , that's sad because this chip requires very low voltage to get high frecuency.

[lowfat]

Forget the voltage, i'm really drunk last night jajajajaj.

PD: i can't pass 223 bclk stable for superpi , that's sad because this chip requires very low voltage to get high frecuency.

What is your PCIe bus @ ?

[Dahaka]

Hi.

I try with 101mhz to 115mhz and nothing.

[FabricioGS]

I have the same problem and also tried 101mhz to 115mhz. Maybe is the heat because I'm in Brazil and its hot as hell this days.

[Salamndar]

I just ordered an EK Classified full block!
I'll receive it later next week, hopefully with my Silverstone ZM1200M PSU and then I'll overclock the hell out of my 950 !!!

[Dahaka]

I have the same problem and also tried 101mhz to 115mhz. Maybe is the heat because I'm in Brazil and its hot as hell this days.

Hi!.

Yep, here in Chile ( Viña del Mar ) is to hot this days, i can't sleep with high temps .

Maybe Dry ice can help now.

[CARLOS*A1]

Hello.

My overclock is a 30Cº Ambient temperature

I'm only 2 hours with her and managed to get blck 230, motherboard 230 blck booting in 106 pci Express

I think I sold the motherboard Shamino