Page 6 of 6 FirstFirst ... 3456
Results 126 to 134 of 134

Thread: Foxconn BloodRage Shared BIOS Settings

  1. #126
    Registered User
    Join Date
    Jun 2008
    Posts
    39
    fantastic mobo
    Attached Images Attached Images

  2. #127
    Xtreme Member
    Join Date
    Nov 2008
    Location
    Brazil
    Posts
    175
    Some results:

    Minimum voltage possible.



    I was trying to run the program 20 loops with Linx, but only the voltage was stable with 1.232v.

    Last edited by _AntLionBR_; 07-31-2010 at 08:15 AM.
    My rig: [i7-990X ES w/AC MX-4 @ 4.5GHz by Prolima Super Mega / Fox x58 BloodRage P11 / Sapphire CFX HD 7970 OC
    A-Data v2.0 2200MHz C8 / A-Data v2.0 1866MHz C8 / Dom.GT 2000C7GTF / Kingston 2000MHz D3T1K3/6GX (All IC Hypers)
    Plextor M5S 128Gb Raid0 / WD 4x VelociRaptor 300Gb (10K) WD3000HLFS / Asus Xonar Essence STX / Seasonic 860 Platinum
    Cooler Master Cosmos II UT w/10x Noctua P12 fans + 2x P14 FLX + 2x Scythe GT P-15 (1850) / BenQ XL2420T 24" 120Hz
    S&S 6g, 7H, Sensei Rubber, 9HD, QcK / Tt Meka G1 / Logitech G5 v2 / Razer Destructor / Puretrak Talent / Senn HD598]

    *My English

  3. #128
    Xtreme Member
    Join Date
    Mar 2009
    Location
    Sunny South Florida
    Posts
    439
    CPU & Batch: i7-990x ES
    RAM Model: Corsair Dominator GT 1600MHz 6GB
    Bios Ver: Quantum BIOS G44

    Cooling system on sig

    CPU Features
    PPM ...............................: Enabled
    EIST ..............................: Enabled
    CxE................................: Auto
    Execute Disable Bit ...............: Disabled
    Virtualization.....................: Disabled
    CPU Write Bach Cache........: Enabled
    Hyper Threading ...................: Enable
    Active Processor Cores ............: All
    TDC Limit...............................: Enabled
    Current TDC Limit....................: 2240
    TDP Limit ..............................: Enabled
    Current TDP Limit....................: 2400
    Current Feedback Override.......: Disabled
    CPU QPI Latency ..............: Auto
    IOH QPI Latency ...............: Auto
    CPU QPI Drive Strength .......: Auto
    IOH QPI Drive Strength .......: Auto

    Memory Settings
    Memory Controller Settings
    IMC Configuration .................: Enabled
    Channel Congifuration .............: Independent
    Channel Interleaving ..............: 6 way
    Rank Interleaving .................: 4 way

    Memory Timings
    Extreme Memory Profile XMP ........: Disabled
    Memory Profile Select .............:
    DRAM Timing Control ...............: Manual
    tCL (CAS Latency) .................: 6T
    tRCG (RAS to CAS Delay) ...........: 7T
    tRP (RAS Precharge) ...............: 6T
    tRAS (Precharge Delay) ............: 16T
    CR (Command Rate) .................: 1T
    tRFC (Refresh Cycle Time) .........: 59T
    tWR (Write Recovery Time) .........: 8T
    tWTR (Write to Read Delay) ........: 14T
    tRRD (RAS to RAS Delay) ...........: 4T
    tRTP (Read to Precharge) ..........: 4T

    All Voltage Settings

    CPU Voltages
    CPU Core Voltage ..................: +310mV (shows 1.440v in windows)
    CPU Target Core Voltage ...........: 1.56375V (VID =1.23) windows 1.440v
    CPU Vdroop Compensation ...........: disabled
    CPU VTT (UnCore) Voltage ..........: +200mV
    1.8 PPL Voltage Setting ...........: 1.800V
    CPU Clock Amplitude Ctrl ..........: 0.800V

    Memory Voltages
    DRAM Voltage ......................: 1.66V
    DIMM1 Vref CA (Addresses) .........: x 0.500
    DIMM1 Vref DQ (Data) ..............: x 0.500
    DIMM2 Vref CA (Addresses) .........: x 0.500
    DIMM2 Vref DQ (Data) ..............: x 0.500
    DIMM3 Vref CA (Addresses) .........: x 0.500
    DIMM3 Vref DQ (Data) ..............: x 0.500

    Chipset Voltages
    X58 IOH Core Voltage .............: 1.18V
    X58 IOH VCCA 1.1V ................: 1.108V
    X58 IOH VCCA 1.5V ................: 1.506V
    ICH10 SB Voltage .................: 1.518V

    OC Gear : Skipping this part

    CPU Turbo .........................: Disabled
    System Turbo ......................: Enabled

    Clock Speed Control Center
    CPU Bclock (FSB) ................: 200MHz
    QPI Link Fast Mode ..............: Enabled
    QPI Multiplier ..................: Auto
    QPI Target Speed ................: 3605MHz (7.2GT/s)
    CPU Core Multiplier .............: x23
    CPU Core Target Speed ...........: 4607MHz
    CPU Uncore Multiplier ...........: x13
    CPU Uncore Target Speed .........: 2606MHz
    Memory Bus Multiplier ...........: x8
    Memory Bus Target Speed .........: 1604MHZ
    PCI Express Bus Clock............: 102MHz


    Last edited by CobraXP; 12-06-2010 at 09:47 PM.
    Intel System
    CPU: Intel i7 990x ES @ 4.2GHz 24/7 still kicking!
    Mobo: Foxconn BloodRage X58 P11 Bios
    Ram: Corsair Dominator 12GB DDR3
    Water Cooling: Apogee XT, MCP655-B pump, MCR220 radiator, XSPC 5.25" Bay reservoir
    Videocard: EVGA Nvidia FTW+ GTX 1060 6GB
    OS HDD: Samsung 950 Pro 512 MB M.2
    Strorage HDD: W.D. VelociRaptor 300GB
    Storage HDD: W.D. 500GB
    PSU: Enermax Evo Galaxy 1250 Watt
    Case: Cooler Master Cosmos S
    Roms: Lite On DVD Burner
    Roms: Asus Bluray Burner
    OS: Windows 7 Ultimate 64-bit

  4. #129
    Xtreme Member
    Join Date
    Apr 2005
    Posts
    172
    I just started trying to overclock this system today. I need a 24/7 stable overclock with low volts. This is my work PC that is always on.

    I printed out someone else's 920 D0 overclock and basically copied it entirely. So far I've figured out that I need to remove some of the excess thermal paste from my Scythe Mugen 2, because I still have load temps in the low 80s and idle temps in the low 30s. Idle temps seem OK, load temps are way wrong. Also, the X58 IOH temp in the bios is 60c. Is this something to be concerned about? And where is it located on the board so I can attempt to cool it down if it is a problem.

    I tried these same settings at 210 blck and the computer locked up during a 32m hyperPI calculation. No BSOD, just a hard lock.

    I7 920 D0
    G Skill F3-12800CL9T-12GBRL
    P11 Bios

    CPU Features
    PPM : Enabled
    EIST : Enabled
    CxE : Disabled
    Execute Disable Bit : Enabled
    Virtualization : Disabled
    Hyper Threading : Disabled
    Active Processor Cores : All
    Current Feedback Override: Disabled(new to P11 bios?)
    Memory Settings
    Memory Controller Settings
    IMC Configuration : Enabled
    Channel Congifuration :Independent
    Channel Interleaving :6 way
    Rank Interleaving :4 way
    Memory Timings
    Extreme Memory Profile XMP : Disabled
    Memory Profile Select :
    DRAM Timing Control : Manual
    tCL (CAS Latency) :9
    tRCG (RAS to CAS Delay) :9
    tRP (RAS Precharge) :9
    tRAS (Precharge Delay) :24
    CR (Command Rate) :2
    tRFC (Refresh Cycle Time) :Auto(86)
    tWR (Write Recovery Time) :Auto(8)
    tWTR (Write to Read Delay) :Auto(14)
    tRRD (RAS to RAS Delay) :Auto(4)
    tRTP (Read to Precharge) :Auto(4)
    B2B CAS Delay: Auto(new to P11 BIOS?)
    All Voltage Settings
    CPU Voltages
    CPU Core Voltage : +120mV
    CPU Target Core Voltage : 1.39500
    CPU Vdroop Compensation : Disabled
    CPU VTT (UnCore) Voltage : +100mV
    1.8 PPL Voltage Setting : 1.800V
    CPU Clock Amplitude Ctrl : 0.900V
    Memory Voltages
    DRAM Voltage : 1.6V
    DIMM1 Vref CA (Addresses) : 0.5
    DIMM1 Vref DQ (Data) :0.5
    DIMM2 Vref CA (Addresses) :0.5
    DIMM2 Vref DQ (Data) :0.5
    DIMM3 Vref CA (Addresses) :0.5
    DIMM3 Vref DQ (Data) :0.5
    Chipset Voltages
    X58 IOH Core Voltage : 1.28V
    X58 IOH VCCA 1.1V : 1.16V
    X58 IOH VCCA 1.5V : 1.518V
    ICH10 SB Voltage : 1.518V
    OC Gear : Skipping this part
    CPU Turbo : Enabled
    System Turbo : Enabled
    Clock Speed Control Center
    CPU Bclock (FSB) : 205
    QPI Link Fast Mode : Enabled
    QPI Multiplier : x18
    QPI Target Speed : 3695mhz
    CPU Core Multiplier : x20
    CPU Core Target Speed : 4106mhz (4309 w/ turbo)
    CPU Uncore Multiplier : x16
    CPU Uncore Target Speed : 3288mhz
    Memory Bus Multiplier : x8
    Memory Bus Target Speed : 1644mhz
    CPU Clock Skew : 0
    IOH Clock Skew : 0

    I'm super happy with this overclock, but I think it can be improved with lower voltages, tighter ram timings, or more of an overclock on the RAM. I know it will do 8-8-8, because it used to boot up at 8-8-8 when I had XMP enabled.

    Once I get this overclock situated, I'm going to try and improve my D0 920 overclock at home. I have an EVGA classified board, D0 920 and a Noctua cooler. My CPU is only at 3.8ghz though.
    Last edited by ElDuderino; 12-08-2010 at 03:20 PM. Reason: Removed outdated sig & added 2 BIOS entries not in the template

  5. #130
    Technician
    Join Date
    Jun 2002
    Location
    Merseyside, UK
    Posts
    2,624
    You want current feedback override enabled to stop it throttling the cpu under heavy load at high clocks.

    More vtt will stabilise higher bclk's and tighter memory timings. +340 is about the limit on air, but it usually works best when its around the same as vcore (if you need it that high). 1.64 to 1.72v is where the bloodrage works best in terms of vddr - reckon you're a little low at 1.6v.

    PLL you can drop to at least 1.616v and cpu clock amplitude is fine at 700mv as well.

    Looking good though, congrats on the board and oc .

  6. #131
    Xtreme Member
    Join Date
    Apr 2005
    Posts
    172
    I'm getting errors in Linx and reboots when I try to play 6 screen eyefinity on stock GPUs. EDIT: I'm thinking my 700w PSU isn't enough to push 6 monitors on my main 2gb 5870 as well as powering the 4.2GHz overclock on the 920. I'm trying to figure out how juicy of a PSU I need to buy. I think 1200w should cover me.

    Here is a shot of my Linx error:


    I'm rebooting to double check my BIOS template and I will edit this post once I have that ready.
    EDIT: These are the settings I'm running.
    CPU & Batch (920 D0)
    RAM Model (12gb Gskill F3-12800CL9-4GBRL)
    Bios Ver: Quantum BIOS (P11)

    CPU Features >>>>>>>>>>>>>>>>>>
    PPM : Enabled
    EIST : Disabled
    CxE : Disabled
    Execute Disable Bit : Disabled
    Virtualization : Disabled
    Hyper Threading : Disabled
    CPU Write Back Cache: Enabled
    Active Processor Cores : All
    Current Feedback Override: Enabled
    Memory Settings >>>>>>>>>>>>>>>>
    Memory Controller Settings
    IMC Configuration : Enabled
    Channel Congifuration : Independent
    Channel Interleaving : 6 way
    Rank Interleaving : 4 way
    Memory Timings >>>>>>>>>>>>>>>>>
    Extreme Memory Profile XMP : Disabled
    Memory Profile Select :
    DRAM Timing Control : Manual
    tCL (CAS Latency) : 9
    tRCG (RAS to CAS Delay) : 9
    tRP (RAS Precharge) : 9
    tRAS (Precharge Delay) : 24
    CR (Command Rate) : 2T
    tRFC (Refresh Cycle Time) : Auto(86)
    tWR (Write Recovery Time) : Auto(8)
    tWTR (Write to Read Delay) : Auto(14)
    tRRD (RAS to RAS Delay) : Auto(4)
    tRTP (Read to Precharge) : Auto(4)
    B2B CAS Delay: Auto
    All Voltage Settings >>>>>>>>>>>>>>
    CPU Voltages
    CPU Core Voltage : +50mV
    CPU Target Core Voltage : 1.335V
    CPU Vdroop Compensation : Disabled
    CPU VTT (UnCore) Voltage : +200mV
    1.8 PLL Voltage Setting : 1.617V
    CPU Clock Amplitude Ctrl : 0.7V
    Memory Voltages
    DRAM Voltage : 1.65V
    DIMM1 Vref CA (Addresses) : 0.5
    DIMM1 Vref DQ (Data) : 0.5
    DIMM2 Vref CA (Addresses) : 0.5
    DIMM2 Vref DQ (Data) : 0.5
    DIMM3 Vref CA (Addresses) : 0.5
    DIMM3 Vref DQ (Data) : 0.5
    Chipset Voltages
    X58 IOH Core Voltage : 1.3V
    X58 IOH VCCA 1.1V : 1.16V
    X58 IOH VCCA 1.5V : 1.518V
    ICH10 SB Voltage : 1.518V
    OC Gear : Skipping this part >>>>>>>>>
    CPU Turbo : Enabled
    System Turbo : Enabled
    Clock Speed Control Center
    CPU Bclock (FSB) : 205
    QPI Link Fast Mode : Enabled
    QPI Multiplier : x18
    QPI Target Speed : 3695MHz
    CPU Core Multiplier : x20
    CPU Core Target Speed : 4106(4309 w/ turbo)
    CPU Uncore Multiplier : x16
    CPU Uncore Target Speed : 3288MHz
    Memory Bus Multiplier : x8
    Memory Bus Target Speed : 1644MHz
    PCI Express Bus Clock: 101MHz
    CPU Clock Skew : 0
    IOH Clock Skew : 0
    Last edited by ElDuderino; 12-16-2010 at 01:15 PM. Reason: added BIOS template

  7. #132
    Registered User
    Join Date
    Dec 2010
    Location
    Ukraine, Donbass
    Posts
    12
    CPU (950 D0)
    RAM Model KHX2333C9D3T1K3\3GX
    Bios Ver: G44
    My resalt...

  8. #133
    Registered User
    Join Date
    Oct 2009
    Location
    Sofia, Bulgaria
    Posts
    19
    CPU i7 920
    RAM Mushkin Redline 12800 6-8-6-24
    Bios Ver: G42

    Cooling Custom build SS

    CPU Features
    PPM ...............................: Enabled
    EIST ..............................: Disable
    CxE................................: Disable
    Execute Disable Bit ...............: Disabled
    Virtualization.....................: Disabled
    CPU Write Bach Cache........: Enabled
    Hyper Threading ...................: Disable
    Active Processor Cores ............: All
    Current Feedback Override.......: Enable
    CPU QPI Latency ..............: Auto
    IOH QPI Latency ...............: Auto
    CPU QPI Drive Strength .......: Auto
    IOH QPI Drive Strength .......: Auto

    Memory Settings
    Memory Controller Settings
    IMC Configuration .................: Enabled
    Channel Congifuration .............: Independent
    Channel Interleaving ..............: 6 way
    Rank Interleaving .................: 4 way

    Memory Timings
    Extreme Memory Profile XMP ........: Disabled
    Memory Profile Select .............:
    DRAM Timing Control ...............: Manual
    tCL (CAS Latency) .................: 6T
    tRCG (RAS to CAS Delay) ...........: 8T
    tRP (RAS Precharge) ...............: 6T
    tRAS (Precharge Delay) ............: 20T
    CR (Command Rate) .................: 1T
    tRFC (Refresh Cycle Time) .........: 72T
    tWR (Write Recovery Time) .........: Auto
    tWTR (Write to Read Delay) ........: Auto
    tRRD (RAS to RAS Delay) ...........: Auto
    tRTP (Read to Precharge) ..........: Auto

    All Voltage Settings

    CPU Voltages
    CPU Core Voltage ..................: +160mV
    CPU Target Core Voltage ...........: 1.32125V (VID =1.16125)
    CPU Vdroop Compensation ...........: disabled
    CPU VTT (UnCore) Voltage ..........: +40mV
    1.8 PPL Voltage Setting ...........: 1.617V
    CPU Clock Amplitude Ctrl ..........: 0.700V

    Memory Voltages
    DRAM Voltage ......................: 1.5V
    DIMM1 Vref CA (Addresses) .........: x 0.500
    DIMM1 Vref DQ (Data) ..............: x 0.500
    DIMM2 Vref CA (Addresses) .........: x 0.500
    DIMM2 Vref DQ (Data) ..............: x 0.500
    DIMM3 Vref CA (Addresses) .........: x 0.500
    DIMM3 Vref DQ (Data) ..............: x 0.500

    Chipset Voltages
    X58 IOH Core Voltage .............: 1.18V
    X58 IOH VCCA 1.1V ................: 1.177V
    X58 IOH VCCA 1.5V ................: 1.518V
    ICH10 SB Voltage .................: 1.518V


    CPU Turbo .........................: Enabled
    System Turbo ......................: Enabled

    Clock Speed Control Center
    CPU Bclock (FSB) ................: 231MHz
    QPI Link Fast Mode ..............: Enabled
    QPI Multiplier ..................: Auto
    QPI Target Speed ................: 4168MHz (8.3GT/s)
    CPU Core Multiplier .............: x20
    CPU Core Target Speed ...........: 4620MHz
    CPU Uncore Multiplier ...........: x12
    CPU Uncore Target Speed .........: 2772MHz
    Memory Bus Multiplier ...........: x6
    Memory Bus Target Speed .........: 1386MHZ
    PCI Express Bus Clock............: 108MHz



    With 234 BCLK system freeze in 7-8 Linx`s loop without BSOD and error code. I`ll try again soon.
    Last edited by lkozarov; 01-03-2011 at 06:44 AM.
    AsrockZ87E4/i7 4770K/2x8GB@2.4GHz/HD4850/2xSamsung 840Pro-RAID0/SS X-850
    i7 3770K/i73930K/i52500K/i7920/i7950/XeonW3570/C2DE8600

  9. #134
    Registered User
    Join Date
    Dec 2010
    Posts
    13
    Right, here are my settings for 4.3GHz (hyperthreading off)

    CPU; Intel Core i7 920 D0
    Mobp; Foxconn Bloodrage GTI
    RAM; 6GB (3 x 2GB) OCZ Gold DDR 3 (8-8-8-24)
    Bios Ver: G42
    Cooling; Titan Fenrir TTC N85 modded with 2x120mm fans
    Case; Coolermaster CM 690 Dominator Pure Black & loads of 120mm fans!

    CPU Features

    PPM ...............................: Enabled
    EIST ..............................: Disabled
    CxE................................: Disabled
    Execute Disable Bit ...............: Enabled
    Virtualization.....................: Enabled
    CPU Write Bach Cache........: Enabled
    Hyper Threading ...................: Disabled
    Active Processor Cores ............: All
    Current Feedback Override.......: Enabled
    CPU QPI Latency ..............: Auto
    IOH QPI Latency ...............: Auto
    CPU QPI Drive Strength .......: Auto
    IOH QPI Drive Strength .......: Auto

    Memory Settings
    Memory Controller Settings
    IMC Configuration .................: Enabled
    Channel Congifuration .............: Independent
    Channel Interleaving ..............: 6 way
    Rank Interleaving .................: 4 way

    Memory Timings
    Extreme Memory Profile XMP ........: Disabled
    DRAM Timing Control ...............: Manual
    Current Timings 8-8-8-24-1-59-8-14-4-4

    tCL (CAS Latency) .................: 8T
    tRCG (RAS to CAS Delay) ...........: 8T
    tRP (RAS Precharge) ...............: 8T
    tRAS (Precharge Delay) ............: 24T
    CR (Command Rate) .................: Auto
    tRFC (Refresh Cycle Time) .........: Auto
    tWR (Write Recovery Time) .........: Auto
    tWTR (Write to Read Delay) ........: Auto
    tRRD (RAS to RAS Delay) ...........: Auto
    tRTP (Read to Precharge) ..........: Auto

    All Voltage Settings

    CPU Voltages
    CPU Core Voltage ..................: +20mV
    CPU Target Core Voltage ...........: 1.24500
    CPU Vdroop Compensation ...........: Disabled
    CPU VTT (UnCore) Voltage ..........: +80mV
    1.8 PPL Voltage Setting ...........: 1.617V
    CPU Clock Amplitude Ctrl ..........: 0.700V

    Memory Voltages
    DRAM Voltage ......................: 1.64V
    DIMM1 Vref CA (Addresses) .........: x 0.500
    DIMM1 Vref DQ (Data) ..............: x 0.500
    DIMM2 Vref CA (Addresses) .........: x 0.500
    DIMM2 Vref DQ (Data) ..............: x 0.500
    DIMM3 Vref CA (Addresses) .........: x 0.500
    DIMM3 Vref DQ (Data) ..............: x 0.500

    Chipset Voltages
    X58 IOH Core Voltage .............: 1.16V
    X58 IOH VCCA 1.1V ................: 1.108V
    X58 IOH VCCA 1.5V ................: 1.506V
    ICH10 SB Voltage .................: 1.506V


    CPU Turbo .........................: Always On
    System Turbo ......................: Enabled

    Clock Speed Control Center
    CPU Bclock (FSB) ................: 205MHz
    QPI Link Fast Mode ..............: Enabled
    QPI Multiplier ..................: Auto
    QPI Target Speed ................: 3695MHz (7.4GT/s)
    CPU Core Multiplier .............: x19
    CPU Core Target Speed ...........: 3901MHz
    CPU Uncore Multiplier ...........: xAuto
    CPU Uncore Target Speed .........: 3288MHz
    Memory Bus Multiplier ...........: Auto
    Memory Bus Target Speed .........: 1644MHZ
    PCI Express Bus Clock............: 102MHz

    i7 920 @4.2GHz HT | Bloodrage GTI X58 G42 | 6GB OCZ Gold 1600MHz
    Asus GTX 470 800/1600/1760 | Corsair HX750W | Coolermaster CM690

Page 6 of 6 FirstFirst ... 3456

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •