Foxconn BloodRage Shared BIOS Settings

[NODO-GT]

CPU & Batch (Core i7 920 D0 3844A934)
RAM Model (OCZ 3x1GB 1600MHz CL7)
Bios Ver: Quantum BIOS (G25)

CPU Features
PPM : Enabled
EIST : Enabled
CxE : Disabled
Execute Disable Bit : Enabled
Virtualization : Enabled
Hyper Threading : On
Active Processor Cores : All
Memory Settings
Memory Controller Settings
IMC Configuration : Enabled
Channel Congifuration : INDEPENDENT
Channel Interleaving : 6 WAY
Rank Interleaving : 4 WAY
Memory Timings
Extreme Memory Profile XMP : Disabled
DRAM Timing Control : Manual
tCL (CAS Latency) : 6
tRCG (RAS to CAS Delay) : 6
tRP (RAS Precharge) : 6
tRAS (Precharge Delay) : 16
CR (Command Rate) : 92
All Voltage Settings
CPU Voltages
CPU Core Voltage : + 130MV
CPU Target Core Voltage : 1.1** Wrong Reading, actual 1.41
CPU Vdroop Compensation : Enabled
CPU VTT (UnCore) Voltage : + 220MV
1.8 PPL Voltage Setting : 1.897
CPU Clock Amplitude Ctrl : 800
Memory Voltages
DRAM Voltage : 1.81 (because of VTT)
DIMM1 Vref CA (Addresses) : x0.500
DIMM1 Vref DQ (Data) : x0.500
DIMM2 Vref CA (Addresses) : x0.500
DIMM2 Vref DQ (Data) : x0.500
DIMM3 Vref CA (Addresses) : x0.500
DIMM3 Vref DQ (Data) : x0.500
Chipset Voltages
X58 IOH Core Voltage : 1.30
X58 IOH VCCA 1.1V : 1.26
X58 IOH VCCA 1.5V : 1.6
ICH10 SB Voltage : 1.506 Default
OC Gear
CPU Turbo : Always On
System Turbo : Enabled
Clock Speed Control Center
CPU Bclock (FSB) : 211
QPI Link Fast Mode : Enabled
QPI Multiplier : 18x
QPI Target Speed : 3798
CPU Core Multiplier : 20
CPU Core Target Speed : 4220 (21x211=4431)
CPU Uncore Multiplier : 12x
CPU Uncore Target Speed : 2532
Memory Bus Multiplier : 6x
Memory Bus Target Speed : 1266
CPU Clock Skew : 500ps
IOH Clock Skew : 300ps

Stable for 1024M Wprime & 32M SuperPI. WaterCooled.

any suggestions? should i try P08 bios? cant go higher than 215 :|

[mal1954]

hi nodo, from what people tell me on the forums g25 is very good for o/c the board, but for 24/7 bios po6 is supposed to be the best bios out so far, so it depends what you want the system for i use mine for a good alround speed for 24/7, at 4 ghz and memory at 1600 the maximum voltage doesnt go much over 1.225 which is the intel recommended max for the Do cpu....(not 1.36 as the co-c1 versions are...hope this helps

[Mescalamba]

I think that those CPU/IOH clock skews are little bit worth nothing.. only help I noticed was at very high FSB (220). Maybe try it without them..

G25 is good.. I had very good results with P06/07 .. running P08 now, not exactly totaly happy from that.. P08 is definetly not better for OCing. But it fixes some bug.. so good if someone experience some bugs..

vCore voltage.. if Im correct, max "safe" from Intel is 1,55V. D0 or C0, doesn't matter.. its just better revision.. CPU is still 45nm, so theres no reason to change voltage..

BTW. I think your tRFC is 92, not Command rate. (you can try higher for higher FSB, but not sure it helps..) and changing PCi-E clock to 103 might help a little bit..

IOH VCCA 1.1V survives 1.3V .. I tried 1.34V and its still working.. helps a little bit in high FSB.

I see you have VTT only +220mV .. well for BCLK 220 I needed I think +400mV.

If you have chipset on water, it should survive up to 1.7V VTT. Not recommanded on air.. So higher VTT is one way to get more BCLK. Plus you can try adding some QPI PPL voltage (up to 2V).

Yea and definately change CPU amplitude to max .. 1.000 V.

[NODO-GT]

Mescalamba & mal1954
thank for your reply.

i want higher VTT but then i need very high voltage on memory, minimal difference is 0.35, but i found that 0.48 difference between memory and VTT makes system much stable. i sometimes system failed to boot with higher VTT and same DRAM voltage (difference 0.40), when i increased Dram voltage it booted and was quite stable... I'll increase CPU amplitude, PLL, IOH 1.1v to 1.3 (i have chipset on stock active cooling...). i'll try to find a way to increase VTT and make system stable.
and yes Command Rate was 1 and tRFC 92
so for Overclocking (not 24/7 setup), G25 is best bios, thats what i wanted to know.

[Mescalamba]

I kinda ignore that low limit.. cause.. I understand why its bad to have bigger than 0,5V difference between VTT and vDimm.. but not sure why having some lower limit? I tried VTT same as vDimm.. and my system is still ok.

VTT is currently on 1.35V
vDIMM at 1.6V

Everything fine.. if it die.. well, it wasn't fine..

[NODO-GT]

didn't post with higher VTT than 220-240, tried different DRAM voltage's....
PCI @ 102MHz
CPU amplitude @ 1.000 V
IOH VCCA 1.1V @ 1.3V
PLL @ 2.0v
with this settings couldn't post at BCLK higher than 213
lowering VTT helped posting up to 218MHz, but didn't boot to windows (lost stability)
somethings wrong with VTT... :|

[Mellowyellow]

I just wanted to say hello, I am ordering My Bloodrage tonight. So i will be on here a bit. Any ram this board doesn't like that anyone know of?

[mal1954]

the only ram that i have heard people talk about having problems with so far is ocz 2000 the cheaper stuff, brilliant ram is dominator gt and 2000 kingston hyperx both with xmp thats the stuff best to go for if you have the bucks...p.s by the way if you are going to pick up your board today check it out first for bent pins, lots of these are around and its the only thing they will not replace the board for...user error...
(by the way your girlfriend looks nice)lol

[Mescalamba]

I just wanted to say hello, I am ordering My Bloodrage tonight. So i will be on here a bit. Any ram this board doesn't like that anyone know of?

Stay away from Elpida Hyper chips and you'll be fine. Kinda hard today.. Bloodrage is fine with almost everything, but for OCing some D9JNM based will be best I guess.. (Crucial "Value" 1333 CL9 ones.. for example )

[MrFixit]

I am also saying hello, new to the Forum. Passion about Bloodrage is awesome here, I fell in love with the thing as soon as I saw it.
Looking to learn from you expert guys how to get this unit OC'd. My first OC was an E8500 on ASUS P5Q, but that was a cake walk compared to what I see here!
I am looking forward to benefiting from the P06 templates here (THANKS)


Thanks to UTNorris for my first P06 OC settings. Not quite at 200 yet, but I'm hoping.

G25 worked well to get the XMP profile on high speed RAM, but I had to find the sweet spot. My CL8 2000Mhz Mushkin goes to CL7@1905MHz 8-)

Here it is:

CPU & Batch core i7 920 2.66 D0
RAM Model DDR3 2000 (PC3 16000) 8-8-7-24 Model 998707 Running@1905Mhz 7-7-7-20 1.65v
Bios Ver: Quantum BIOS G25

CPU Features
PPM : Enable
EIST : Enable
CxE : Disable
Execute Disable Bit : Enable
Virtualization : Disable
Hyper Threading :Enable
Active Processor Cores :2 - I'm still on XP :-(
Memory Settings
Memory Controller Settings
IMC Configuration :Enable
Channel Congifuration :Independent
Channel Interleaving : 6 way
Rank Interleaving : 4 way
Memory Timings
Extreme Memory Profile XMP : ENABLE
Memory Profile Select : Auto
DRAM Timing Control : By sPD
tCL (CAS Latency) : Auto
tRCG (RAS to CAS Delay) : Auto
tRP (RAS Precharge) :Auto
tRAS (Precharge Delay) :Auto
CR (Command Rate) :Auto
tRFC (Refresh Cycle Time) :Auto
tWR (Write Recovery Time) :Auto
tWTR (Write to Read Delay) :Auto
tRRD (RAS to RAS Delay) : Auto
tRTP (Read to Precharge) : Auto
All Voltage Settings
CPU Voltages
CPU Core Voltage : +80mV (will I need more here when 4 cores on? hmmm)
CPU Target Core Voltage : 1.02375-? 1.376 Actual
CPU Vdroop Compensation : Enable
CPU VTT (UnCore) Voltage : +160mV (Bare Minimum for post here)
1.8 PPL Voltage Setting : 1.800v
CPU Clock Amplitude Ctrl : 0.800v
Memory Voltages
DRAM Voltage : 1.65v
DIMM1 Vref CA (Addresses) : 0.500
DIMM1 Vref DQ (Data) : 0.500
DIMM2 Vref CA (Addresses) : 0.500
DIMM2 Vref DQ (Data) : 0.500
DIMM3 Vref CA (Addresses) : 0.500
DIMM3 Vref DQ (Data) : 0.500
Chipset Voltages
X58 IOH Core Voltage : 1.26v
X58 IOH VCCA 1.1V : 1.125v
X58 IOH VCCA 1.5V : 1.5v
ICH10 SB Voltage :
OC Gear :
CPU Turbo : Enable
System Turbo : Enabled
Clock Speed Control Center
CPU Bclock (FSB) :190Mhz
QPI Link Fast Mode :enable
QPI Multiplier : x18
QPI Target Speed : 3425 (6.8 GT/s)
CPU Core Multiplier :x20
CPU Core Target Speed : 3806MHz
CPU Uncore Multiplier : x20
CPU Uncore Target Speed :3810MHz
Memory Bus Multiplier : x10
Memory Bus Target Speed :1905MHz
CPU Clock Skew : OPS
IOH Clock Skew : OPS

[mal1954]

hi Mescalamba, i have been looking into your thoughts on vtt v cpu voltage, and have found out when i set my board up to factory defaults
there seems to be little difference in cpu v vtt volts wise, the readings i am getting from cpu-z and other software is running the cpu at 2.67
cpu core volts (idle)0.93 under load 1.22
north bridge = 1.09
and the cpu vtt 1.17 (under Load 1.25)and vdimm 1.60 constant......so by going by the manufacturers settings this should answer a few questions....(hopefully)

[Death_Dealer83]

CPU & Batch (3849A866)
RAM Model (Mushkin 998708 2000mhz)
Bios Ver: Quantum BIOS P06 and G25

CPU Features
PPM : Enabled
EIST : Enabled
CxE : Disabled
Execute Disable Bit : Disabled
Virtualization : Disabled
Hyper Threading : Diabled
Active Processor Cores : ALL
Memory Settings
Memory Controller Settings
IMC Configuration :Enabled
Channel Congifuration :Independent
Channel Interleaving :6
Rank Interleaving :4
Memory Timings
Extreme Memory Profile XMP : Disabled
Memory Profile Select :auto
DRAM Timing Control :Manual
tCL (CAS Latency) :6
tRCG (RAS to CAS Delay) :6
tRP (RAS Precharge) :5
tRAS (Precharge Delay) :auto
CR (Command Rate) :1T
tRFC (Refresh Cycle Time) :auto
tWR (Write Recovery Time) : auto
tWTR (Write to Read Delay) : auto
tRRD (RAS to RAS Delay) : auto
tRTP (Read to Precharge) : auto
All Voltage Settings
CPU Voltages
CPU Core Voltage :+30mV
CPU Target Core Voltage :1.26750
CPU Vdroop Compensation :Enabled
CPU VTT (UnCore) Voltage :+80
1.8 PPL Voltage Setting :1.800
CPU Clock Amplitude Ctrl :.800
Memory Voltages
DRAM Voltage :1..65
DIMM1 Vref CA (Addresses) :.500
DIMM1 Vref DQ (Data) :.500
DIMM2 Vref CA (Addresses) :.500
DIMM2 Vref DQ (Data) :.500
DIMM3 Vref CA (Addresses) :.500
DIMM3 Vref DQ (Data) :.500
Chipset Voltages
X58 IOH Core Voltage :1.10
X58 IOH VCCA 1.1V :1.108
X58 IOH VCCA 1.5V :1.506
ICH10 SB Voltage :1.506
OC Gear : Skipping this part
CPU Turbo : Always On
System Turbo : Enabled
Clock Speed Control Center
CPU Bclock (FSB) : 200
QPI Link Fast Mode :
QPI Multiplier : x18
QPI Target Speed : 3605(7.2GT/s)
CPU Core Multiplier : x18
CPU Core Target Speed :3605
CPU Uncore Multiplier : 18
CPU Uncore Target Speed : 3609
Memory Bus Multiplier : 8
Memory Bus Target Speed : 1604
CPU Clock Skew : Ops
IOH Clock Skew :Ops

[MrFixit]

Nice DeathDealer, glad to see XMP working for someone else....Yay Mushkin!

[rioja]

are all these bios settings really stable for prime, linpack etc?

[YMAA]

Extreme Memory Profile XMP : D

Pretty sure he's running it disabled - just forgot the space between the : and the D.

[Death_Dealer83]

are all these bios settings really stable for prime, linpack etc?

Sorry that is not XMP enabled. no worky, but manual set the setting and yea...
As far as stable I run Linx and Prime95 on all four cores and it works.
Just got the HT working too will have to post those settings soon... but need just a little more vcore and had to get vtt to +200mv.

I will run all test, OCCT, PRIME95, for 2hrs. I really dont run past that cause I get no errors but remember I am actively cooling this sucker too.. Coolit Boreas setting under a Heatkiller..
G

[Death_Dealer83]

CPU & Batch (3849A866)
RAM Model (Mushkin 998708 2000mhz 8-8-7-24-1T)
Bios Ver: Quantum BIOS (G25)

CPU Features
PPM : Enabled
EIST : Enabled
CxE : Disabled
Execute Disable Bit : Enabled
Virtualization : Disabled
Hyper Threading : Enabled
Active Processor Cores : All
Current Feedback Override: Enabled (added this one for HT otherwise Multi Drops)
Memory Settings
Memory Controller Settings
IMC Configuration : Enabled
Channel Congifuration :Independent
Channel Interleaving :6
Rank Interleaving :4
Memory Timings
Extreme Memory Profile XMP : Disabled
Memory Profile Select :auto
DRAM Timing Control :Manual
tCL (CAS Latency) :6
tRCG (RAS to CAS Delay) :6
tRP (RAS Precharge) :5
tRAS (Precharge Delay) :auto
CR (Command Rate) :1T
tRFC (Refresh Cycle Time) :Auto
tWR (Write Recovery Time) : Auto
tWTR (Write to Read Delay) : Auto
tRRD (RAS to RAS Delay) : Auto
tRTP (Read to Precharge) : Auto
All Voltage Settings
CPU Voltages
CPU Core Voltage : +40mV 1.27750 Cpuz reports 1.26, and jumps to 1.328v under load CPUZ-1.51, Hottest core 74C. coolant @ 32-33 C
CPU Target Core Voltage : 1.27750
CPU Vdroop Compensation : Enabled
CPU VTT (UnCore) Voltage : +200mV
1.8 PPL Voltage Setting : 1.856
CPU Clock Amplitude Ctrl : .800
Memory Voltages
DRAM Voltage :1.65
DIMM1 Vref CA (Addresses) :.500
DIMM1 Vref DQ (Data) : :.500
DIMM2 Vref CA (Addresses) : :.500
DIMM2 Vref DQ (Data) : :.500
DIMM3 Vref CA (Addresses) : :.500
DIMM3 Vref DQ (Data) : :.500
Chipset Voltages
X58 IOH Core Voltage :1.10
X58 IOH VCCA 1.1V :1.108
X58 IOH VCCA 1.5V :1.506
ICH10 SB Voltage :1.506
OC Gear : Skipping this part
CPU Turbo : Always on
System Turbo : Enabled
Clock Speed Control Center
CPU Bclock (FSB) : 200
QPI Link Fast Mode : Enabled
QPI Multiplier : X18
QPI Target Speed : 3605
CPU Core Multiplier : X18
CPU Core Target Speed : 3605
CPU Uncore Multiplier : X18
CPU Uncore Target Speed : 3609
Memory Bus Multiplier : X8
Memory Bus Target Speed : 1604
PCI Express Bus Clock : 100
CPU Clock Skew : Ops
IOH Clock Skew : Ops


Oh and if I enable the AutoShut down. The readings go crazy... All voltages go to 4.06 not acutally go there but reports as such, and does not happen all the time random but only happens if I set it....
Crazy Chit...

[mk-ultra]

here's my settings for 220x18 ~ nearly 4ghz

nothing crazy just a low voltage overclock and 15 pass linpack stable(can also do 221x18) with those setttings, memory was kinda out of the way at 1323, but with 6-6-6-14 timings, it pushes more than decent bandwidth



CPU & Batch (w3520 / 3845A935)
RAM Model (6GB G.Skill PI Black (F3-12800CL8T-6GBPI-B))
Bios Ver: Quantum BIOS (G25)

CPU Features
PPM : Disabled
EIST : Disabled
CxE : Disabled
Execute Disable Bit : Disabled
Virtualization : Disabled
Hyper Threading : Enabled
Active Processor Cores : All
Memory Settings
Memory Controller Settings
IMC Configuration : Enabled
Channel Congifuration : Independant
Channel Interleaving : 6 way
Rank Interleaving : 4 way
Memory Timings
Extreme Memory Profile XMP : Disabled
Memory Profile Select : Auto
DRAM Timing Control : By SPD
tCL (CAS Latency) :
tRCG (RAS to CAS Delay) :
tRP (RAS Precharge) :
tRAS (Precharge Delay) :
CR (Command Rate) :
tRFC (Refresh Cycle Time) :
tWR (Write Recovery Time) :
tWTR (Write to Read Delay) :
tRRD (RAS to RAS Delay) :
tRTP (Read to Precharge) :
All Voltage Settings
CPU Voltages
CPU Core Voltage : + 120mv
CPU Target Core Voltage : 1.245 (CPUZ-IDLE=1.232)(CPUZ-LOAD=1.248)(DMM-IDLE=1.240)(DMM-LOAD=1.256)
CPU Vdroop Compensation : Disabled
CPU VTT (UnCore) Voltage : +160 (DMM=1.323)
1.8 PPL Voltage Setting : 1.688 (DMM=1.666)
CPU Clock Amplitude Ctrl : .800mv
Memory Voltages
DRAM Voltage : 1.64 (DMM-1.65)
DIMM1 Vref CA (Addresses) : .500
DIMM1 Vref DQ (Data) : .500
DIMM2 Vref CA (Addresses) : .500
DIMM2 Vref DQ (Data) : .500
DIMM3 Vref CA (Addresses) : .500
DIMM3 Vref DQ (Data) : .500
Chipset Voltages
X58 IOH Core Voltage : 1.26 (DMM=1.277)
X58 IOH VCCA 1.1V : 1.125 (DMM=1.110)
X58 IOH VCCA 1.5V : 1.506 (DMM=1.463)
ICH10 SB Voltage : 1.506
OC Gear : Skipping this part
CPU Turbo : Disabled
System Turbo : Enabled
Clock Speed Control Center
CPU Bclock (FSB) : 220
QPI Link Fast Mode : Enabled
QPI Multiplier : x18
QPI Target Speed : 3965mhz
CPU Core Multiplier : x18
CPU Core Target Speed : 3965mhz
CPU Uncore Multiplier : x18
CPU Uncore Target Speed : 3970mhz
Memory Bus Multiplier : x6
Memory Bus Target Speed : 1323mhz

[mal1954]

Nice one MK-ULTRA, like the very low voltages, would be interseting to see what you can do with bios P06 at 4 ghz the best i have seen voltage on cpu under max load 1.41, and the memoty running at 1600..
well done

[josk1]

hi guys,
got my new D0 (batch 3851A286) and finished my cosmos s rig so I finally could test a bit more today... I used the chart a friend gave me of his stabilised tweaks, and here it is



I actually managed to boot mine until 212 bclk, and went up to 217 in Vista with Aegis... finally went under 9sec @ super pi 1M

I'm using P06 bios. Will try P07, and maybe G25 too.
I'll let you know

[Mescalamba]

IOH survives up to 1.3V (tested) .. and it kinda helps with higher BCLK..

217.. nice without mod, rlly.. tough, why those hyper-high CPU voltages? I made 225 with stock vCore?

[josk1]

225 on a C0 with stock Vcore???
you must have a champion !

really, I still have a lotta tweaking ahead, but these are my first results for now. I'll try lowering the Vcore then

[mal1954]

Hi guys, and well done josk1 on your 4.7 clock brilliant, has anybody got a good stable setting for the do 920 with nice low voltages. for 4.2ghz....4.3ghz...i mean something nice and stable that wont kill the system over a longer period...would be interseting to see.....regards

[josk1]

look at my "200 bclk" line... not much volts added, but stable on a 24/7 scale !!!

ps: 4.573, not 4.7... I wish I went that high! 'will try 4.6 though

[mal1954]

thanks josk1 will give it a try ....regards