Compression fittings what fits what

**SNiiPE_DoGG** · 12-31-2008, 10:42 AM

Attached is the First version of the XtremeSystems Compression fittings Chart!

I will add to it on a weekly basis and update the root file here

Please post new findings on this thread and they will be added

V1 was by our member zlojack and I have now taken over maintenance of it, thankyou for your contribution man

**PsYcHoNo0b727** · 12-31-2008, 10:59 AM

Danger Den Tieton GPU block works with 7/16ID 5/8OD BitsPower compression fittings, on the copper side only and not using the back plate (only using RAMSinks).

Also, D-Tek FuZion V2 works with the 7/16ID 5/8OD fittings as long as you use 45degree rotary fittings.

**skinnee** · 12-31-2008, 12:12 PM

OCZ Hydroflow, all compression fittings in the chart above fit.

**SNiiPE_DoGG** · 12-31-2008, 12:15 PM

k guys, it will be a few hours before I can recreate the spreadsheet

I will format it in a more XS themed manner

**SNiiPE_DoGG** · 12-31-2008, 12:52 PM

can someone hook me up with a 400x120pixel wide koolance logo for the chart? thanks

**Eddie3dfx** · 12-31-2008, 12:58 PM

Why bring up the past...

**SNiiPE_DoGG** · 12-31-2008, 01:09 PM

Originally Posted by Eddie3dfx

no offense, but if zlojack created the chart and doesn't want it posted in a certain area, then why would you go against his wishes?

Might as well grab the sidewinders chart and post it on xs as well.

I dont care what he wishes, he has no copyright on a compatibility chart and all XS users have a right to data that was compiled from our posts

**zlojack** · 12-31-2008, 01:13 PM

Originally Posted by SNiiPE_DoGG

I dont care what he wishes, he has no copyright on a compatibility chart and all XS users have a right to data that was compiled from our posts

Then compile it yourself, or at least ask me...

That was pretty low.

**Waterlogged** · 12-31-2008, 01:16 PM

Originally Posted by zlojack

Then compile it yourself, or at least ask me...

That was pretty low.

No lower than yanking it.

**zlojack** · 12-31-2008, 01:20 PM

Originally Posted by Waterlogged

No lower than yanking it.

Do you even know why I yanked it?

Have you asked me?

Both you and Sniipe_Dogg are making some assumptions about me without even asking.

All Sniipe had to do was shoot me a PM and ask what had happened. Instead, he decided to steal my work. Great!

I know that most of the information was put up there by the community and that all I did was compile it. I also had everything hosted with Bobly and was looking for a different place to host it.

But whatever...

**zlojack** · 12-31-2008, 01:24 PM

That was a complete lack of respect by you Sniipe_Dogg. I've never been anything but courteous with you. All you needed to do was PM me and we could have sorted this in no time if you wanted to recreate the stuff here.

Bad move...bro. Bad move.

**Waterlogged** · 12-31-2008, 01:26 PM

I've been told by a little birdy

They are removing all "information" from various sites and only posting it on "his" site. They are looking to market it to vendors and manufacturers for exclusive deals on parts and testing.

If this is not the case, please, do inform us.

**fox3** · 12-31-2008, 01:28 PM

BP 3/8 (5/8) will not work on the AquagrattiX for HD 4870 X2.

Posted for the benifit of XS community ...

**zlojack** · 12-31-2008, 01:32 PM

Originally Posted by Waterlogged

I've been told by a little birdy

If this is not the case, please, do inform us.

I don't know anything about that.

I know that I had the info hosted with someone else, so I took it down.

If Sniipe wanted to rehost it and put it back up, all he needed to do was PM me.

I thought that he and I at least were at that level.

**Waterlogged** · 12-31-2008, 01:42 PM

Originally Posted by zlojack

I don't know anything about that.

I know that I had the info hosted with someone else, so I took it down.

If Sniipe wanted to rehost it and put it back up, all he needed to do was PM me.

I thought that he and I at least were at that level.

Wait, you mean to tell me that you deleted the entire topic because you needed to re-host an image?

**bentleya** · 12-31-2008, 01:42 PM

guys stop fighting, SNiiPE_DoGG had the right to do it, as we the XS guys gave you what to put down

right SNiiPE_DoGG, with The BP and TFC the same measument fittings have the same measuments so whatever you have done on the BP do on the TFC and so on

understand?

**Movieman** · 12-31-2008, 01:42 PM

Originally Posted by zlojack

Do you even know why I yanked it?

Have you asked me?

Both you and Sniipe_Dogg are making some assumptions about me without even asking.

All Sniipe had to do was shoot me a PM and ask what had happened. Instead, he decided to steal my work. Great!

I know that most of the information was put up there by the community and that all I did was compile it. I also had everything hosted with Bobly and was looking for a different place to host it.

But whatever...

Ok, I'll ask. Why did you pull it from XS?

edit: Just read, ok, if rehosting was the issue then snipedog did you a favor and saved you the time.
My thanks for taking the time to make this chart.

**zlojack** · 12-31-2008, 01:49 PM

No worries.

As I said...I have no problem with the information being made available since it came from the users themselves and I just collected it. My issue is just the way Sniipe went about it and the continued sideswiping in which you'll notice I haven't taken part. (At least MM had the decency to edit the snide remarks from the first post). I've now PMd Sniipe about this so I'll leave off with the continued commenting in the thread. Happy watercooling people and

for the chart

And yes, Waterlogged, I deleted the post, not realizing that it would kill the whole thread (I thought only mods could do that). It was not my finest moment.

**SNiiPE_DoGG** · 12-31-2008, 01:50 PM

I am creating a new spreadsheet now, it will be maintained by me and this is all a moot issue

**Movieman** · 12-31-2008, 01:55 PM

After reading all it is quite possible that all of this was a misunderstanding of what was happenning and I'd suggest to all that we look at it that way and move on.
Happy New Year to all of you.
Dave

**Eddie3dfx** · 12-31-2008, 01:57 PM

Happy New Year FTW!!!

Actually on a serious note, will feser ever make 7/16 compression fittings?

**bentleya** · 12-31-2008, 02:09 PM

Originally Posted by Eddie3dfx

Happy New Year FTW!!!

Actually on a serious note, will feser ever make 7/16 compression fittings?

haha, yerp >http://www.feser-one.com/site/produc...roducts_id=317

**Spankyfart** · 12-31-2008, 02:10 PM

Happy new year.

Please don't ban me

**Waterlogged** · 12-31-2008, 02:13 PM

Originally Posted by bentleya

haha, yerp >http://www.feser-one.com/site/produc...roducts_id=317

He meant 7/16" I.D.

**bentleya** · 12-31-2008, 02:22 PM

i knew that i was just testing, that you all clicked my link

and the answer is yes haha

but TFC will have lots of new stuff next year, so i would guess there would be some unless they are not allowed to make them

Thread: Compression fittings what fits what

Thread Tools

Search Thread

Rate This Thread

Display

Compression fittings what fits what

Bookmarks

Bookmarks

Posting Permissions