athlon64 overclock record. all owners please post

**Verdict** · 07-15-2004, 06:44 PM

core goes up 740 with 1.6v but i have 10 minutes time drive tests, then AGP slot gets water and i have to stop tests

i drive tests C02

**spellsfromhell** · 07-15-2004, 08:45 PM

Originally posted by Mariachi
That's a really new chip... Congrats. Temps?

about 50-53c full load and 40-45c idle with fans at 75%, 8kda3+ doesnt read cpu temps below 0, so i dno..

**s e t h** · 07-15-2004, 11:08 PM

thermalright slk 948u 20' ambient

ada3700aep5ar
caabc0417tpmw
9556722d40053

anyone know who has the fastest air super-pi

**=[PULSAR]=** · 07-15-2004, 11:15 PM

Give me a couple weeks and I'll beat your Super PI with a aircooled 3000+

Noise isnt a factor is it, I'll put the machine in a wind tunnel.

Hopefully I'll get a nice newcastle core and hit like 2.65ghz (9x295) and run full 1:1 DDR590

**s e t h** · 07-15-2004, 11:25 PM

=[PULSAR]= is your kv8pro a revision 1.1 and if so does vdimm work after 2.8v

**=[PULSAR]=** · 07-15-2004, 11:31 PM

Yep 1.1 with a working lock, but why lock the AGP/PCI when its helps 3D performance. Well in bios you can only set it to 2.8v but once you get a OS installed get the first version of uGuru and you can raise it to 3.2v, so the first time you boot just set the vdimm to 3.2v and reboot to bios and you will have a couple wierd characters where vdimm should be but under voltage monitoring it shows 3.2v. Also, VTT does not go any higher than 1.4v so you dont have to worry about burning the mem controller on your cpu.

**s e t h** · 07-15-2004, 11:42 PM

if vtt stays at 1.4 that will create instability using vdimm from 2.9-3.2. i know cause i had a kv8-max3 with the vtt issue and vdimm above 2.8 was useless. u sure vtt stays below 1.4? i was hoping that they'd fixed it with rev 1.1

oh well just have to mod then

**=[PULSAR]=** · 07-15-2004, 11:58 PM

Well the vtt stays at a constant 1.45v, but I havent found any instabilities about it. At one time I was running OCZ PC3200 @ DDR470 w/3.2v and it worked fine for me.

**s e t h** · 07-16-2004, 12:03 AM

hmmm. i'm def going to test one. thanks for the info

**Mariachi** · 07-16-2004, 05:52 AM

Verdict,

Damn good clocks man...

Kickass chip you got there... full stepping please?

can you test 1m sPi please?

**k|ngp|n** · 07-18-2004, 06:57 AM

A64 retail 3700+
caabc 0411mpmw

Here is a super pi with mushkinlv2 at 3.15v and vapo ls.

**Mariachi** · 07-18-2004, 07:14 AM

Nice clocks king, But put on that baby phasechage and add some voltages... You can reache 3ghz pretty easily.

**k|ngp|n** · 07-18-2004, 07:21 AM

Nice clocks king, But put on that baby phasechage and add some voltages... You can reache 3ghz pretty easily.

I Plan on it .... I'm just playin on air till chilly gets my cascade done. I'm hoping for alot more than 3ghz :P

**Mariachi** · 07-18-2004, 01:09 PM

I think 3.1Ghz + is completely possible with a good 3700+. That would rock, since my CPU maxes out at 3005Mhz, but i'm working on more.

BTW, are you planning some 1:1 action? Maybe you should consiber EB3700

**k|ngp|n** · 07-18-2004, 01:45 PM

I am running it 1:1 in those benches. This one bh-5 stick will go 280-285 1:1 @ 5-2-2-2 but it needs over 3.5v.

The 3700eb looks good to tho.

**Mariachi** · 07-18-2004, 03:42 PM

Kickass mem you got there.

BTW Your PSU is modded?

**Spider** · 07-18-2004, 07:50 PM

Originally posted by =[PULSAR]=
Yep 1.1 with a working lock, but why lock the AGP/PCI when its helps 3D performance. Well in bios you can only set it to 2.8v but once you get a OS installed get the first version of uGuru and you can raise it to 3.2v, so the first time you boot just set the vdimm to 3.2v and reboot to bios and you will have a couple wierd characters where vdimm should be but under voltage monitoring it shows 3.2v. Also, VTT does not go any higher than 1.4v so you dont have to worry about burning the mem controller on your cpu.

does that uguru vdimm trick work with the new epox 250 boards?

**aoc007** · 07-18-2004, 09:01 PM

uguru is on ABit mobos only...

**nutcase** · 07-19-2004, 07:36 AM

This is the Best I can do with this Motherboard

Gigabyte K8NS pro with Vcore and Direct 3.3V Rail Vdimm Mod
AMD64 3200+ (CAAAC 0354)
OCZ PC3200 Plat LE (BH-6) at 2-2-2-7 1:1 and 3.6V Vdimm
OCZ Powerstream 420W PSU
Cooled with stock Prometia Mach 1

The OCZ Powerstream with the Direct 3.3V Mod allows me to adjust Vdimm Voltage to 3.85V

But, This F2 Bios needs a Lot of work.. Multipliers still don't work

**kakaroto** · 07-20-2004, 03:55 AM

My new 3400+ Newcastle arrived

Mobo: EPoX 8KDAJ (5-14 bios, full modded)
Cooling: STOCK BOXED COOLER
temps: 43C idle / 58C stressed.

Hows this baby gonna do under Mach 1, soon more PC results

just a first run ...

**Noldor** · 07-22-2004, 04:51 AM

Was that the max stable OC you could do with the stock hsf? My 3400NC is coming tomorrow hopfully

**kakaroto** · 07-22-2004, 06:37 AM

Originally posted by Noldor
Was that the max stable OC you could do with the stock hsf? My 3400NC is coming tomorrow hopfully

yes, the aluminium boxed cooler is crap

60C stressed.

**Noldor** · 07-22-2004, 06:41 AM

Well, having a A64 at 2.6GHz is still great, and will be great for gaming for a long time too. As soon as i get money for a X800-XT i can start thinking about better cooling. But first things first

**kakaroto** · 07-22-2004, 09:06 AM

Originally posted by Noldor

Well, having a A64 at 2.6GHz is still great, and will be great for gaming for a long time too. As soon as i get money for a X800-XT i can start thinking about better cooling. But first things first

yes i could run 3dmark01, but not many times. its get to hot...
My max was 1.72v...