** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

**Jor3lBR** · 03-07-2009, 02:11 PM

Originally Posted by radaja

here are my new g.skill 2x2GB.just a quick test for vdimm needed.

yes radaja, I forgot to tell ya the less multi or frequency you give to the cpu the less vdimm you will need to run stable.

**radaja** · 03-07-2009, 04:26 PM

oh ok i thought is was cause i was using the 4:5 divider.cause i still cannot get my 9650 or any cpu ive owned to run stable with 500fsb and thier original multiplier.its the hardest thing for me.it was the same thing with my e8400 / e8500 and now my 9650.with the 9650 i can get it to prime at 9x500 but it fails after one or two minutes no matter what i do.the only thing i havent been able to try is upping the vcore above 1.42 while under load.

**PortCitySlim** · 03-07-2009, 10:37 PM

Guys, I always assumed that the yellow dimms were the best to use, but has anyone tried the red slots. I think I might see if I can resolve my issue with the 2.4B strap not booting over 434FSB by switching slots or booting with one stick and then adding another.

**coop** · 03-08-2009, 12:41 AM

frakin' A

**DOM.** · 03-08-2009, 12:54 AM

settings coop ?

i can only get 600 on with auto setting

**fatguy1992** · 03-08-2009, 01:45 AM

coop

Very nice

Could u please post your full BIOS settings?

Thanks

**PortCitySlim** · 03-08-2009, 02:36 AM

Originally Posted by PortCitySlim

Guys, I always assumed that the yellow dimms were the best to use, but has anyone tried the red slots. I think I might see if I can resolve my issue with the 2.4B strap not booting over 434FSB by switching slots or booting with one stick and then adding another.

WOW, I decided to do some wire management on my case tonight and while I was in it I did change from the yellow slots to the red slots. Guess what!? I can now boot into windows using the 2.4B strap and 1.34MCH at 470+FSB. On the other board I used if you used the 2/4 DIMM you lost a bit of memory performance, I haven't tested to see if my RAM performance went down any yet.

**DOM.** · 03-08-2009, 02:42 AM

http://valid.canardpc.com/show_oc.php?id=522756

thanks coop im still working on mine but got to go to sleep

Code:

******Motherboard Intelligent Tweaker (M.I.T.)******
 
Robust Graphics Booster.......................[Auto]
CPU Clock Ratio...............................[7]
Fine CPU Clock Ratio..........................[+0.0]
CPU Frequency 4.2GHz..........................[600x7]
 
******Clock Chip Control******
 
CPU Host Clock Control........................[Enabled]
CPU Host Frequency (Mhz)......................[600]
PCI Express Frequency (Mhz)...................[100]
C.I.A 2.......................................[Disabled] 
 
******Advanced Clock Control******

CPU Clock Drive...............................[800mv]
PCI Express Clock Drive.......................[800mv]
CPU Clock Skew................................[50ps]
MCH Clock Skew................................[50ps]
 
******Motherboard Voltage Control******
 
Load-Line Calibration.........................[Enabled]
CPU Vcore.....................................[1.4v]
CPU Termination...............................[1.34]
CPU PLL.......................................[1.63]
CPU Reference.................................[0.903]
 
MCH Core......................................[1.44]
MCH Reference.................................[0.788]
MCH/DRAM Refernce.............................[normal]
ICH I/O.......................................[normal]
ICH Core......................................[normal]

DRAM Voltage..................................[2.2] 
DRAM Termination..............................[normal]
Channel A Ref.................................[normal]
Channel B Ref.................................[normal]

**TheGanG** · 03-08-2009, 03:23 AM

Hi people!

I got my EP45T-UD3P / DDR3; my first Gigabyte board, but i can't change anything at BIOS, it tries afew times and posts default, even can't change loadline calibration except CPU Eist/C1E/Thermal Monitor... at Advanced BIOS Features. I use ET & SetFSB as OC tools on windows without any issues...

Edit: Recently got F6A BIOS with @BIOS update tool...

**xbiusx** · 03-08-2009, 04:14 AM

Hey guys, i need advices, i`m very stressed with my settings... Some days ago i was using 800x5 very stable but no matter what i do i wasn`t able to rise the fsb to 505. And i decided to reduce the fsb and rise the multi, ok. And now i`m on 490x8.5 very stable as well. So my problem is no matter what i do i can get blend stable at any FSB over 491, ORTHOS fails and the computer restart after few minutes... Is there some limit for clock because i realize that i can`t go over 4.2ghz on blend test, even on lower FSB and high multi like 467x9. Well, i hope someone can figure out what is my problem. I had tested the whole thing with 3 sets of different memory (OCZ, Mushikin, Crucial Ballistix).

Code:

******Gigabyte EP45 UD3P******

E8500 490 X 8.5 4165MHz 

Robust Graphics Booster.........................[ Auto     ] 
CPU Clock Ratio.................................[ 8        ] 
Fine CPU Clock Ratio............................[ 0.5        ] 
CPU Frequency 4.0GHz...........................[ 500 x 8.5  ]

******Clock Chip Control******

CPU Host Clock Control..........................[ Enabled  ] 
CPU Host Frequency (Mhz)........................[ 490      ] 
PCI Express Frequency (Mhz).....................[ 104      ] Best so far (Tested 99-104)
C.I.A 2 ..................................................[Disabled] 

******Advanced Clock Control******

CPU Clock Drive.................................[ 700mv   ] Tested 800mv
PCI Express Clock Drive.........................[ 900mv   ] 
CPU Clock Skew..................................[ 0ps      ] Tested 0-50ps
MCH Clock Skew..................................[ 0ps     ] Tested 0-150ps

******DRAM Performance Control******

Performance Enhance [Standard] 
Extreme Memory Profile (XMP)....................[ Disabled ] 
(G) MCH Frequency Latch.........................[ 400MHz   ] 
System Memory Multipler.........................[ 2.00D    ] 
Memory Frequency 1066...........................[ 980     ] 
DRAM Timing Selectable..........................[ Manual   ] 

CAS Latency Time................................[ 5        ] 
tRCD............................................[ 5        ] 
tRP.............................................[ 5        ] 
tRAS............................................[ 15       ] 

******Advanced Timing Control******

tRRD............................................[ 4    ] Auto
tWTR............................................[ 4     ] Auto
tWR.............................................[ 8    ] Auto
tRFC............................................[ 68       ] Auto
tRTP............................................[ 4     ] Auto
Command Rate (cmd)..............................[ 2T     ] 

******Channel A Timing Settings******     

Static tRead Value        [ 11 ] ................[ 9        ] 
tRD Phase0 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto     ] 

tRD 2rd (Differnt Rank)   [ 6 ] ................[ Auto     ]
tWR 2wr (Differnt Rank)   [ 6 ] ................[ Auto     ] 
tWR 2rd (Differnt Rank)   [ 5 ] ................[ Auto     ] 
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto     ] 

Dimm 1 Clock Skew Control.......................[ Auto     ] 
Dimm 2 Clock Skew Control.......................[ Auto     ] 
DDR Write Training..............................[ Auto     ] 

******Channel A Driving Settings****** 

Drive Strength Profile..........................[ Auto     ] 
Data Driving Pull Up Level......................[ Auto     ] 
cmd Driving Pull Up Level.......................[ Auto     ] 
ctrl Driving Pull Up Level......................[ Auto     ]
clk Driving Pull Up Level.......................[ Auto     ]

Data Driving Pull Down Level....................[ Auto     ] 
cmd Driving Pull Down Level.....................[ Auto     ] 
ctrl Driving Pull Down Level....................[ Auto     ] 
clk Driving Pull Down Level.....................[ Auto     ]

******Channel B Timing Settings******     

Static tRead Value        [ 11 ] ................[ 9        ] 
tRD Phase0 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto     ] 

tRD 2rd (Differnt Rank)   [ 6 ] ................[ Auto     ]
tWR 2wr (Differnt Rank)   [ 6 ] ................[ Auto     ] 
tWR 2rd (Differnt Rank)   [ 5 ] ................[ Auto     ] 
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto     ] 

Dimm 1 Clock Skew Control.......................[ Auto     ] 
Dimm 2 Clock Skew Control.......................[ Auto     ] 
DDR Write Training..............................[ Auto     ] 

******Channel B Driving Settings****** 

Drive Strength Profile..........................[ Auto     ] 
Data Driving Pull Up Level......................[ Auto     ] 
cmd Driving Pull Up Level.......................[ Auto     ] 
ctrl Driving Pull Up Level......................[ Auto     ]
clk Driving Pull Up Level.......................[ Auto     ]

Data Driving Pull Down Level....................[ Auto     ] 
cmd Driving Pull Down Level.....................[ Auto     ] 
ctrl Driving Pull Down Level....................[ Auto     ] 
clk Driving Pull Down Level.....................[ Auto     ]

******Motherboard Voltage Control******

Load-Line Calibration [Enabled] 
CPU Vcore         [ 1.25 ]...................[ 1.39375  ] 
CPU Termination   [ 1.20    ]...................[ 1.30     ]
CPU PLL           [ 1.50    ]...................[ 1.59   ]
CPU Reference     [ 0.760   ]...................[ 0.878   ] ET6 Show 0.815

MCH Core          [1.1      ]...................[ 1.46    ]  
MCH Reference     [0.760    ]...................[ 0.743   ] ET6 Show 0.68
MCH/DRAM Refernce [0.900    ]...................[ Normal   ] 
ICH I/O           [1.500    ]...................[ 1.570   ] 
ICH Core          [1.100    ]...................[ 1.200   ] 

DRAM Voltage      [1.800    ]...................[ 2.100    ] Tested 2.1-2.2
DRAM Termination  [0.900    ]...................[ Auto   ] 
Channel A Ref     [0.900    ]...................[ Auto   ] 
Channel B Ref     [0.900    ]...................[ Auto   ]  

******Advanced BIOS Features******

CPU Multithreading..............................[ Disabled ] 
Limit CPUID Max to 3............................[ Disabled ] 
No-Execute memory Protect.......................[ Disabled ]  
CPU Enhance Halt (CIE)..........................[ Disabled ]  
C2/C2E State Support............................[ Disabled ]  
C4/C4E State Support............................[ Disabled ] 
CPU Thermal Monitor.............................[ Disabled ] 
CPU EIST Function...............................[ Disabled ] 
Virtualization Technology.......................[ Enabled ]

**simoorta** · 03-08-2009, 04:21 AM

Originally Posted by simone18

i dont think so. some people here in italy have ud3r rev1.1 and they aren't able to go over 450fsb. ram only in 1:1. it hasn't same performance of rev1.0
obviously, not all rev1.1 are so bad

Are you talking about me simo??:asd:

Yes guys, my 1.1 doesn't go over 430fsb in 5:6, also witch several voltages. And all is correctly setted.
In 1:1 goes over 430fsb, but it stops at 465fsb + or -.

But I want 600fsb, not 465. :asd:
But I don't understand why the mobo goes as I've explained.

**xavisimao** · 03-08-2009, 04:47 AM

@fatguy
can you post your BIOS setting at stock speed, 3.0ghz overclocked and 3.6ghz overclocked? we do have similar processor, motherboard and rams

specs:
intel Q6600
Gigabyte EP45-UD3R rev 1.1
Corsair dominator 2x1gb 1066mhz

**firas** · 03-08-2009, 06:35 AM

1.920 vdimm with 0.960 worked
even lowered the vcore from 1.25 to 1.225 and ran p95 small ftt before i go to work (still at work)

Code:

******Motherboard Intelligent Tweaker (M.I.T.)******
 
Robust Graphics Booster.........................[ Auto     ]
CPU Clock Ratio.................................[ 8        ]
Fine CPU Clock Ratio............................[ + 0.5    ]
CPU Frequency 3.6GHz............................[ 425 x 8.5  ]
 
******Clock Chip Control******
 
CPU Host Clock Control..........................[ Enabled  ]
CPU Host Frequency (Mhz)........................[ 425      ]
PCI Express Frequency (Mhz).....................[ 100      ]
C.I.A 2 [Disabled] 
 
******Advanced Clock Control******

CPU Clock Drive.................................[ 800mv]
PCI Express Clock Drive.........................[ 900mv]
CPU Clock Skew..................................[ 0ps]
MCH Clock Skew..................................[ 0ps]
 
******DRAM Performance Control******
 
Performance Enhance.............................[Standard]
Extreme Memory Profile (XMP)....................[ Auto   ]
(G) MCH Frequency Latch.........................[ 333    ]
System Memory Multiplier........................[ 2.40B  ]
Memory Frequency   ..............1066.............1020
DRAM Timing Selectable..........................[ Manual ]
 
CAS Latency Time...............[ 5    ].........[ 5     ]
tRCD...........................[ 5    ].........[ 5     ]
tRP............................[ 5    ].........[ 5     ]
tRAS...........................[ 15   ].........[ 15    ]
 
******Advanced Timing Control******
 
tRRD...........................[ 4   ]..........[ Auto     ]
tWTR...........................[ 4   ]..........[ Auto     ]
tWR............................[ 6   ]..........[ Auto     ]
tRFC...........................[ 72   ].........[ 54       ]
tRTP...........................[ 4   ]..........[ Auto     ]
Command Rate (cmd).............[ 0   ]..........[ 2        ]
 
******Channel A Timing Settings******     
 
Static tRead Value        [ 8 ] ................[ 8        ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto     ]
 
tRD 2rd (Differnt Rank)   [ 8 ] ................[ Auto     ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ Auto     ]
tWR 2rd (Differnt Rank)   [ 7 ] ................[ Auto     ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto     ]
 
Dimm 1 Clock Skew Control.......................[ Auto     ]
Dimm 2 Clock Skew Control.......................[ Auto     ]
DDR Write Training..............................[ Auto     ]
 
******Channel A Driving Settings****** 
 
Drive Strength Profile..........................[ Auto     ]
Data Driving Pull Up Level......................[ Auto     ]
cmd Driving Pull Up Level.......................[ Auto     ]
ctrl Driving Pull Up Level......................[ Auto     ]
clk Driving Pull Up Level.......................[ Auto     ]
 
Data Driving Pull Down Level....................[ Auto     ]
cmd Driving Pull Down Level.....................[ Auto     ]
ctrl Driving Pull Down Level....................[ Auto     ]
clk Driving Pull Down Level.....................[ Auto     ]
 
******Channel B Timing Settings******     
 
Static tRead Value        [ 8 ] ................[ 8        ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto     ]
 
tRD 2rd (Differnt Rank)   [ 8 ] ................[ Auto     ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ Auto     ]
tWR 2rd (Differnt Rank)   [ 7 ] ................[ Auto     ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto     ]
 
Dimm 1 Clock Skew Control.......................[ Auto     ]
Dimm 2 Clock Skew Control.......................[ Auto     ]
DDR Write Training..............................[ Auto     ]
 
******Channel B Driving Settings****** 
 
Drive Strength Profile..........................[ Auto     ]
Data Driving Pull Up Level......................[ Auto     ]
cmd Driving Pull Up Level.......................[ Auto     ]
ctrl Driving Pull Up Level......................[ Auto     ]
clk Driving Pull Up Level.......................[ Auto     ]
 
Data Driving Pull Down Level....................[ Auto     ]
cmd Driving Pull Down Level.....................[ Auto     ]
ctrl Driving Pull Down Level....................[ Auto     ]
clk Driving Pull Down Level.....................[ Auto     ]
 
******Motherboard Voltage Control******
 
Load-Line Calibration...........................[ Enabled  ]
CPU Vcore         [ 1.25    ]...................[ 1.2250V  ]
CPU Termination   [ 1.20    ]...................[ 1.20     ]
CPU PLL           [ 1.50    ]...................[ 1.50     ]
CPU Reference     [ 0.760   ]...................[ Auto     ]
 
MCH Core          [ 1.100   ]...................[ 1.240   ]
MCH Reference     [ 0.760   ]...................[ 0.800   ]
MCH/DRAM Refernce [ 0.900   ]...................[ 0.960   ]
ICH I/O           [ 1.500   ]...................[ 1.500   ]
ICH Core          [ 1.100   ]...................[ 1.100   ]

DRAM Voltage      [1.8]...................[1.920] 
DRAM Termination  [0.9]...................[0.960]
Channel A Ref     [0.9]...................[0.960]
Channel B Ref     [0.9]...................[0.960]

*****************Advanced BIOS Features********* 


Limit CPUID Max to 3 ................. [disable] 
No-Execute memory Protect ............ [disable]
CPU Enhance Halt (CIE) ............... [disable] 
C2/C2E State Support ................. [disable] 
C4/C4E State Support ................. [disable] 
CPU Thermal Monitor................... [disable] 
CPU EIST Function..................... [disable]
Virtualization Technology ............ [disable]

**Hoss331** · 03-08-2009, 06:48 AM

Originally Posted by PortCitySlim

WOW, I decided to do some wire management on my case tonight and while I was in it I did change from the yellow slots to the red slots. Guess what!? I can now boot into windows using the 2.4B strap and 1.34MCH at 470+FSB. On the other board I used if you used the 2/4 DIMM you lost a bit of memory performance, I haven't tested to see if my RAM performance went down any yet.

I gave this a try this morning and it seemed to help my problem but not fix it. In the yellow slots I can boot up to 1.36mch, in the red slots I can boot up to 1.4mch and everest scores seem to be unchanged. Tonight ill try my 8500s in the red slots and see what happens.

**pierrandre** · 03-08-2009, 09:41 AM

I'm wondering if I can use DDR3 sticks on my EP45-UD3P... someplace I read that I can, somewhere else I read that I can't..
I also read that DDR2 and DDR3 sticks have a different notch to avoid trouble
Can you provide me some information about the sticks I could buy.. I've got two 2 gig noname sticks (working with a Q9550 at 471 FSB @ 1,9vdimm - 5-5-5-15 PL9) but I need 8 gig of ram.. and I want to increase my FSB..
I have selected this kit of DDR3 http://www.ocztechnology.com/product...800_reaper_hpc and I wonder if it's a good choise for my board (GA-EP45-UD3P, but I'm already in the right thread)...

If it's not can you give me some advice on a good DDR2 Kit (I'll buy it here : http://www.rueducommerce.fr/Composan...ttes-Memoires/ ) and I'm totaly LOST !!!
thank you

**PortCitySlim** · 03-08-2009, 11:11 AM

Originally Posted by Hoss331

I gave this a try this morning and it seemed to help my problem but not fix it. In the yellow slots I can boot up to 1.36mch, in the red slots I can boot up to 1.4mch and everest scores seem to be unchanged. Tonight ill try my 8500s in the red slots and see what happens.

Man, after I did that I sat there in my chair laughing at myself for not trying it before. One thing I have always seen people do when they are having RAM issues is try the other slots and if that don't work try booting with one stick. Like you said it helps but does not completely fix the problem. I am just glad I do not have to use ET6 anymore, I really did not like that program.

**fatguy1992** · 03-08-2009, 11:37 AM

Originally Posted by pierrandre

I'm wondering if I can use DDR3 sticks on my EP45-UD3P... someplace I read that I can, somewhere else I read that I can't..
I also read that DDR2 and DDR3 sticks have a different notch to avoid trouble
Can you provide me some information about the sticks I could buy.. I've got two 2 gig noname sticks (working with a Q9550 at 471 FSB @ 1,9vdimm - 5-5-5-15 PL9) but I need 8 gig of ram.. and I want to increase my FSB..
I have selected this kit of DDR3 http://www.ocztechnology.com/product...800_reaper_hpc and I wonder if it's a good choise for my board (GA-EP45-UD3P, but I'm already in the right thread)...

If it's not can you give me some advice on a good DDR2 Kit (I'll buy it here : http://www.rueducommerce.fr/Composan...ttes-Memoires/ ) and I'm totaly LOST !!!
thank you

You CAN NOT run DDR3 RAM on the EP45-UD3P, you need the EP45T-UD3P.

**~~Zucker2k~~** · 03-08-2009, 11:47 AM

What's the best bios for the UD3P V. 1.1? Running latest f9a, but still open for suggestions. I have mixed first impressions, but I'll leave those for later. Still, I'm having some stretches of fun with this board.

Richard.

**Homeless2** · 03-08-2009, 12:40 PM

So far with the F9A bios i've noticed two things. First being that one of my fans runs at 100% for the first 3 seconds of boot compared to none. Second is that raid initialization is pretty much instant now

**radaja** · 03-08-2009, 03:43 PM

the board they sent me back had F6 so i flashed it back to F5 cause i use a usb wireless keyboard and mouse and bio's past F5 have these two usb settings disabled by default and its a pain to have to use a wired keyboard after a clear cmos or set to optimized defaults to have to go in and enabled them.i havent tried the F9 ones yet.

**Jor3lBR** · 03-08-2009, 03:55 PM

Originally Posted by Zucker2k

What's the best bios for the UD3P V. 1.1? Running latest f9a, but still open for suggestions. I have mixed first impressions, but I'll leave those for later. Still, I'm having some stretches of fun with this board.

Richard.

I've tried every BIOS but the new F9a and they all seam fine for Quads. I currently use F8.

Originally Posted by radaja

the board they sent me back had F6 so i flashed it back to F5 cause i use a usb wireless keyboard and mouse and bio's past F5 have these two usb settings disabled by default and its a pain to have to use a wired keyboard after a clear cmos or set to optimized defaults to have to go in and enabled them.i havent tried the F9 ones yet.

Radaja that is strange I clear cmos and I can get into BIOS screen with USB keyboard normally and then change these settings, you only lose USB Keyboard when you get passed RAID init screen.

**~~Zucker2k~~** · 03-08-2009, 04:28 PM

@ Radaja: I can confirm both F6 and F9A work with my USB kb.

Well, F9A doesn't seem bad at all. I'm new to this board so I have no point of reference. This board is quirky to say the least; coming from the rampage formula in my sig. I thought I could throw stuff at it like I did on that board, well, I had a good lesson and paid closer attention and learned some few things. Ambients a huge problem for me now. It's about 75f in the computer room and grows to 80f+ when priming. I have decided to go slowly till I can improve the temps here. In any case, how about this for my daily summer clocks?

Gigabyte GA-EP45UD3P
Intel C2Q Q9650 @ 8x500 FSB
4x 2GB G.Skill F2-7200CL4D Pi-Black @ DDR2 1000 5-5-5-15 (turbo mode enabled)
Windows Vista x64 SP2 (Full Install from previous board)

Next -> 8.5 x 500

Cheers, Richard.

Edit: vdroop is huge, 0.046v. This board needs no mods right?

**radaja** · 03-08-2009, 04:37 PM

that is strange.my wireless usb keyboard just will not work until i go into the bios using my wired keyboard and go to the integrated periphial page and manually enable both keyboard and mouse.

**andressergio** · 03-08-2009, 05:51 PM

Today i started loving this mobo....

I left the MF2 days, today i swapped mobos and re built my system with the UD3P and the new Q9650 vid 1,1875, this is my first SPI 1M

Cheers
Sergio

**Jor3lBR** · 03-08-2009, 06:18 PM

Originally Posted by andressergio

Today i started loving this mobo....

I left the MF2 days, today i swapped mobos and re built my system with the UD3P and the new Q9650 vid 1,1875, this is my first SPI 1M
Cheers
Sergio

Well done Sergio!

I'm glad I brought you to the DarK SidE

Thread: Official Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

Thread Tools

Search Thread

Rate This Thread

Display

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

Thread: ** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

Thread Tools

Search Thread

Rate This Thread

Display

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

Thread: Official Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P